the NIC drivers as well as the PHY drivers to take advantage of the
mii_attach() introduced in r213878 to get rid of certain hacks. For
the most part these were:
- Artificially limiting miibus_{read,write}reg methods to certain PHY
addresses; we now let mii_attach() only probe the PHY at the desired
address(es) instead.
- PHY drivers setting MIIF_* flags based on the NIC driver they hang
off from, partly even based on grabbing and using the softc of the
parent; we now pass these flags down from the NIC to the PHY drivers
via mii_attach(). This got us rid of all such hacks except those of
brgphy() in combination with bce(4) and bge(4), which is way beyond
what can be expressed with simple flags.
While at it, I took the opportunity to change the NIC drivers to pass
up the error returned by mii_attach() (previously by mii_phy_probe())
and unify the error message used in this case where and as appropriate
as mii_attach() actually can fail for a number of reasons, not just
because of no PHY(s) being present at the expected address(es).
Reviewed by: jhb, yongari
The following systems are affected:
- MPC8555CDS
- MPC8572DS
This overhaul covers the following major changes:
- All integrated peripherals drivers for Freescale MPC85XX SoC, which are
currently in the FreeBSD source tree are reworked and adjusted so they
derive config data out of the device tree blob (instead of hard coded /
tabelarized values).
- This includes: LBC, PCI / PCI-Express, I2C, DS1553, OpenPIC, TSEC, SEC,
QUICC, UART, CFI.
- Thanks to the common FDT infrastrucutre (fdtbus, simplebus) we retire
ocpbus(4) driver, which was based on hard-coded config data.
Note that world for these platforms has to be built WITH_FDT.
Reviewed by: imp
Sponsored by: The FreeBSD Foundation
IF_ADDR_UNLOCK() across network device drivers when accessing the
per-interface multicast address list, if_multiaddrs. This will
allow us to change the locking strategy without affecting our driver
programming interface or binary interface.
For two wireless drivers, remove unnecessary locking, since they
don't actually access the multicast address list.
Approved by: re (kib)
MFC after: 6 weeks
CPU for too long period than necessary. Additively, interfaces are kept
polled (in the tick) even if no more packets are available.
In order to avoid such situations a new generic mechanism can be
implemented in proactive way, keeping track of the time spent on any
packet and fragmenting the time for any tick, stopping the processing
as soon as possible.
In order to implement such mechanism, the polling handler needs to
change, returning the number of packets processed.
While the intended logic is not part of this patch, the polling KPI is
broken by this commit, adding an int return value and the new flag
IFCAP_POLLING_NOCOUNT (which will signal that the return value is
meaningless for the installed handler and checking should be skipped).
Bump __FreeBSD_version in order to signal such situation.
Reviewed by: emaste
Sponsored by: Sandvine Incorporated
Prior to this fix, IEVENT register was always cleared before calling
tsec_error_intr_locked(), which prevented error recovery actions from
happening with polling enabled (and could lead to serious problems, including
controller hang).
Submitted by: Marcin Ligenza marcinl ! pacomp dot com dot pl
- interrupt coalescing
- polling
- jumbo frames
- multicast
- VLAN tagging
The enhanced version of the chip (eTSEC) can also take advantage of:
- TCP/IP checksum calculation h/w offloading
Obtained from: Freescale, Semihalf
Split the driver into the core functionality part (sys/dev/tsec/if_tsec.c) and
the bus attachment (sys/dev/tsec/if_tsec_ocp.c).
This lets better integrate and maintain the driver in other environments with
different attachment abstractions (there is at least one other FreeBSD port --
MPC83xx -- which uses this TSEC driver, but with different local bus model
i.e. some OF derivative). While there, clean up and fix minor cosmetics.
Obtained from: Semihalf
might be currently programmed into the registers.
Underlying firmware (U-Boot) would typically program MAC address into the
first unit only, and others are left uninitialized. It is now possible to
retrieve and program MAC address for all units properly, provided they were
passed on in the bootinfo metadata.
Reviewed by: imp, marcel
Approved by: cognet (mentor)
TSEC is the MAC engine offering 10, 100 or 1000 Mbps speed and is found on
different Freescale parts (MPC83xx, MPC85xx). Depending on the silicon version
there are up to four TSEC units integrated on the chip.
This driver also works with the enhanced version of the controller (eTSEC),
which is backwards compatible, but doesn't take advantage of its additional
features (various off-loading mechanisms) at the moment.
Approved by: cognet (mentor)
Obtained from: Semihalf
MFp4: e500
