The previous calculation used an approximation which was only valid in
cases where the means being compared were similar; this resulted in very
odd claims being made, e.g. that 0 +/- 0 is a difference of -100% +/- 1%
from 100 +/- 1.
The new calculation scales sample standard deviations by the means, and
yields approximately correct percentage difference bounds providing that
the reference population is bounded away from zero. (In the case where
the values being compared are not sufficiently bounded away from zero,
the distribution of ratios becomes much harder to calculate, and is not
likely to be useful anyway.)
Note that when ministat is used for its intended purpose of determining
whether two samples are statistically different, this change is unlikely
to have any noticeable effect; in such cases the means will be similar
enough that the correction applied here will be minimal.
In r297602, which included a __FreeBSD_version bump to 1100105, we changed
sed 'i' and 'a' from discarding whitespaces to conform with what GNU and
sysvish sed do.
There are arguments in favor of keeping the old behavior but the new
behavior is also useful for migration purposes. It seems important to at
least consider the case of developers depending on the previous behavior,
so add a CFLAG to enable the old behaviour.
PR: 213474
MFC after: 5 days
Compiler-rt and LLVM's libunwind provide a suitable replacement for
libgcc.a, libgcc_eh.a, and libgcc_s.so.
Remove the now-unused LLVM_LIBUNWIND block from gnu/lib/libgcc.
PR: 213480 [exp-run]
Reviewed by: brooks, ed
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8189
is not going to recover until the system is reset. Treat it as a special
case and don't allow it to fall through to quasi-success.
Reviewed by: ken, imp
Obtained from: Netflix
MFC after: 3 days
the components are reset). Therefore retries are pointless. This is very
visible in SATL systems, for example an LSI SAS controller and a SATA HDD/SSD.
Reviewed by: ken
Obtained from: Netflix
MFC after: 3 days
Bay Trail has three banks of GPIOs exposed to userland as /dev/gpiocN,
where N is 1, 2, and 3. Pins in each bank are pre-named to match names
on boards schematics: GPIO_S0_SCnn, GPIO_S0_NCnn, and GPIO_S5_nn.
Controller supports edge-triggered and level-triggered interrupts but
current version of the driver does not have interrupts support
Requests which cannot be satisfied by allocators at boot time often
have unrealizable parameters. Waiting for the pagedaemon' start would
hang the boot if done in the thread0 context and just never succeed if
executed from another thread. In fact, for very early stages, sleep
attempt panics with obscure diagnostic about the scheduler state, and
explicit panic in vm_wait() makes the investigation much shorter by
cut off the examination of the thread and scheduler.
Theoretically, some subsystem might grab a resource to exhaustion, and
free it later in the boot process. If this unlikely scenario does
appear for real, the way to diagnose the trouble can be revisited.
Reported by: emaste
Reviewed by: markj
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D8421
The audio controller in the H3 is more or less the same as A10/A20 except
some registers are shuffled around. The mixer interface, however, is
completely different between SoCs. Separate a10_mixer_class and
h3_mixer_class implementations are now made available. This will also make
adding support for other SoCs easier in the future.
Reviewed by: andrew, ganbold
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D8425
they shouldn't be.
I used this during driver bring-up to find that the Linux driver holds a
whole lot of locks whilst doing their equivalent of busdma operations.
If this works out well, it should be added to the other architecture busdma
implementations to aid in similar debugging.
Tested:
* bounce buffer and dmar busdma, Lenovo X230 laptop, all the internal
hardware
* ath(4) too
Discussed with: jhb
This is a long time coming. The general pieces have been floating around
in a local repo since circa 2012 when I dropped the net80211 support
into the tree.
This allows the per-chain RSSI and NF to show up in 'ifconfig wlanX list sta'.
I haven't yet implemented the EVM hookups so that'll show up; that'll come
later.
Thanks to Susie Hellings <susie@susie.id.au> who did the original work
on this a looong time ago for a company we both worked at.
Now that the changes to the dirname(3) function had some time to settle,
let's go ahead and use the same approach for replacing basename(3) by a
simple implementation that modifies the input string, thereby making it
thread-safe and guaranteed to succeed.
Unlike dirname(3), this function already had a thread-safe variant
basename_r(3). This function had its own set of problems, like having an
upper bound on the pathname length. Keep this function around for
compatibility, but remove most references from the man page. Make the
man page more similar to that of dirname(3).
As the basename_r(3) function is only provided by FreeBSD (and Bionic),
depending on its use is even more implementation defined than assuming
that basename(3) is thread-safe.
Reviewed by: emaste
Differential Revision: https://reviews.freebsd.org/D8382
be accessed by root. It uses unsigned ints instead of size_t
to preserve the ABI.
PR: 207627
Submitted by: ryan@ryanday.net (with slight tweaks)
MFC after: 1 month
illumos/illumos-gate@620f322510620f322510https://www.illumos.org/issues/6051
Currently lzc_receive() requires that its snapname argument is a snapshot name
(contains '@').
zfs receive allows to specify just a dataset name and would try to deduce the
snapshot name from the stream.
I propose to allow lzc_receive() to do the same.
That seems to be quite easy to implement, it requires only a small amount of
logic, it does not require any additional system calls or any additional data
from the stream.
The benefit is that the new behavior would allow to keep the snapshot names the
same between the sender and receiver at zero cost, without a need to pass the
names out of band.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Author: Andriy Gapon <avg@icyb.net.ua>
MFC after: 2 weeks
This change reverts most of r281985.
The method did not map to anything defined by SMBus protocol and could
not be implemented for SMBus controllers.
This change is obviously not backwards compatible, but I have good
reasons to believe that there have never been any users of SMB_TRANS.
Discussed with: grembo, jhb
MFC after: 6 weeks
To enable event sourcing from atkbd kern.evdev.rcpt_mask value
should have bit 3 set.
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D8381
The device doesn't accurately update the CHANCMP address with the device state
when the device is suspended or halted. So, read the CHANSTS register to check
for those states.
We still need to read the CHANCMP address for the last completed descriptor.
Sponsored by: Dell EMC Isilon
