built without support for miibus PHYs. Most ed cards don't need
miibus support, so it's useful to be able to avoid the bloat of
all the mii devices for small fixed-purpose kernels.
appear in /dev. Interface hardware ioctls (not protocol or routing) can
be performed on the descriptor. The SIOCGIFCONF ioctl may be performed
on the special /dev/network node.
ethernet controllers. This adds support for the 3Com 3c996-T, the
SysKonnect SK-9D21 and SK-9D41, and the built-in gigE NICs on
Dell PowerEdge 2550 servers. The latter configuration hauls ass:
preliminary measurements show TCP speeds of over 900Mbps using
only normal size frames.
TCP/IP checksum offload, jumbo frames and VLAN tag insertion/stripping
are supported, as well as interrupt moderation.
Still need to fix autonegotiation support for 1000baseSX NICs, but
beyond that, driver is pretty solid.
- SC_CUT_SPACES2TABS - when copying text into the cut buffer convert leading
spaces into the tabs;
- SC_CUT_SEPCHARS="XYZ" - treat supplied characters as possible words
separators when the driver searches for words boundaries when doing cut
operation.
Also unify cut code a bit to decrease amount of duplicated code. This fixes
line cut mode, so that it is no longer pads line with useless spaces.
Approved by: ru
the size of the kernel virtual address space relatively painlessly.
Userland will adapt via the exported kernbase symbol. Increasing
this causes the user part of address space to reduce.
amdpm(4) and smb(4).
This device can be used with userland programs such as sysutils/lmmon
to retrieve sensor information from the motherboard.
PR: kern/23989
Obtained from: Matthew C. Forman <mcf@dmu.ac.uk>
Based on: alpm(4)
to locore to process the @fptr relocations in the dynamic executable.
* Don't initialise the timer until *after* we install the timecounter to
avoid a race between timecounter initialisation and hardclock.
* Tidy up bootinfo somewhat including adding sanity checks for when the
kernel is loaded without a recognisable bootinfo.
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
* Switch to proc0's stack and backing store before calling ia64_init
so that we don't rely on the loader's stack at all.
* Change kernel entry point name from locorestart to __start.
the cwd is looked up inside the kernel. The native getcwd() in libc
handles this in userland if __getcwd() fails.
Obtained from: NetBSD via OpenBSD
Tested by: Chris Casey <chriss@phys.ksu.edu>, Markus Holmberg <markush@acc.umu.se>
Reviewed by: Darrell Anderson <anderson@cs.duke.edu>
PR: kern/24315
level implementation stuff out of machine/globaldata.h to avoid exposing
UPAGES to lots more places. The end result is that we can double
the kernel stack size with 'options UPAGES=4' etc.
This is mainly being done for the benefit of a MFC to RELENG_4 at some
point. -current doesn't really need this so much since each interrupt
runs on its own kstack.
then one can restart from a panic by resetting the panicstr variable to
NULL. This commit conditionalizes the previously committed functionality
on this variable. It also removes the __dead2 attribute from the panic()
function so that when one continues from a panic() the behavior will
be predictable.
information. The default limits only effect machines with > 1GB of ram
and can be overriden with two new kernel conf variables VM_SWZONE_SIZE_MAX
and VM_BCACHE_SIZE_MAX, or with loader variables kern.maxswzone and
kern.maxbcache. This has the effect of leaving more KVM available for
sizing NMBCLUSTERS and 'maxusers' and should avoid tripups where a sysad
adds memory to a machine and then sees the kernel panic on boot due to
running out of KVM.
Also change the default swap-meta auto-sizing calculation to allocate half
of what it was previously allocating. The prior defaults were way too high.
Note that we cannot afford to run out of swap-meta structures so we still
stay somewhat conservative here.
"./foo.ko". Use "/full/path/foo.ko" instead so that when the path is
reported as being an absolute path to the "shared library", at least
it's not really a relative path.
Obtained from: LOMAC/FreeBSD project
just before the memory hole to 4 megs. Special case building exception.s
like locore.s, it needs to at the beginning so the branches out from the
trap table don't overflow.
commented out in the entire life of the 2.x+ branch and given the amount
of gcc-specific code we have and the warning checks that gcc does I'm not
sure that it is going to get us much for some time.
debugging support as well. Debugging module support is handled
identically to kernel debugging support, right down to poor
choice of make variable names.
Tunables are now derived at boot time from maxusers. ie: change maxusers
via a tunable and all the derivative settings change. You can change
the other tunables individually as well. Even hz etc is tunable.
blown over by the Hurricane and had a house dropped on you by the Tornado.
Now it's time to have your parade rained on by... the Typhoon!
This commit adds driver support for 3Com 3cR990 10/100 ethernet
adapters based on the Typhoon I and Typhoon II chipsets. This is actually
a port of the OpenBSD driver with many hacks by me.
No Virginia, there isn't any support for the hardware crypto yet. However
there is support for TCP/IP checksum offload and VLANs.
Special thanks go to Jason Wright, Aaron Campbell and Theo de Raadt for
squeezing enough info out of 3Com to get this written, and for doing
most of the hard work.
Manual page is included. Compiled as a module and included in GENERIC.
directory does not exist, instead of creating/overwriting a file
with the name of the (expected) directory. Yes, this deviates a bit
from nearly all other install targets in the tree, but let's face it,
removing a modules directory is not all that uncommon a mistake,
and finding a file with the contents of the last module installed
is a baaad surprise at boot time..
PR: 26317
Submitted by: "T. William Wells" <bill@twwells.com> (the PR)
Gregory Bond <gnb@itga.com.au> (the actual patch)
Reviewed by: silence on -arch and -audit for the last 10 days
MFC after: 2 weeks
o Much cleanly separate NetBSD(XS) / FreeBSD(CAM) codes.
o Improve tagged queing support (full QTAG).
o Improve quirk support.
o Improve parity error retry.
o Impliment wide negotheation.
o Cmd link support.
o Add copyright of CAM part.
o Change for CAM_NEW_TRAN_CODE.
o Work around for buggy KME UJDCD450.
o stg: add disconnet condition.
o nsp: use suspend I/O.
and more. I thank Honda-san.
conf/options.pc98: add CT_USE_RELOCATE_OFFSET and CT_BUS_WEIGHT
dev/{ct,ncv,nsp,stg}/*_{pccard,isa}.c: add splcam() before calling
attach/detach functions.
Tested by: bsd-nomads
Obtained from: NetBSD/pc98
- All sources are built in a single object, reducing namespace pollution.
- Kill the ready queue, and handle a busy response to mly_start in callers
rather than deferring the command.
- Improve our interaction with CAM:
- Don't advertise physical channels as SCSI busses by default.
- use the SIM queue freeze capability rather than queueing CDBs internally.
- force bus reprobe at module load time.
- Clean up more resources in mly_free.
- Tidy up debugging levels.
- Tidy up handling of events (mostly just code cleanliness).
- Use explanatory macros for operations on bus/target/channel numbers.
we are required to do if we let user processes use the extra 128 bit
registers etc.
This is the base part of the diff I got from:
http://www.issei.org/issei/FreeBSD/sse.html
I believe this is by: Mr. SUZUKI Issei <issei@issei.org>
SMP support apparently by: Takekazu KATO <kato@chino.it.okayama-u.ac.jp>
Test code by: NAKAMURA Kazushi <kaz@kobe1995.net>, see
http://kobe1995.net/~kaz/FreeBSD/SSE.en.html
I have fixed a couple of style(9) deviations. I have some followup
commits to fix a couple of non-style things.
directories. When enabled via "options UFS_DIRHASH", in-core hash
arrays are maintained for large directories. These allow all
directory operations to take place quickly instead of requiring
long linear searches. For now anyway, dirhash is not enabled by
default.
The in-core hash arrays have a memory requirement that is approximately
half the size of the size of the on-disk directory file. A number
of new sysctl variables allow control over which directories get
hashed and over the maximum amount of memory that dirhash will use:
vfs.ufs.dirhash_minsize
The minimum on-disk directory size for which hashing should be
used. The default is 2560 (2.5k).
vfs.ufs.dirhash_maxmem
The system-wide maximum total memory to be used by dirhash data
structures. The default is 2097152 (2MB).
The current amount of memory being used by dirhash is visible
through the read-only sysctl variable vfs.ufs.dirhash_maxmem.
Finally, some extra sanity checks that are enabled by default, but
which may have an impact on performance, can be disabled by setting
vfs.ufs.dirhash_docheck to 0.
Discussed on: -fs, -hackers
Also removed some spl's and added some VM mutexes, but they are not actually
used yet, so this commit does not really make any operational changes
to the system.
vm_page.c relates to vm_page_t manipulation, including high level deactivation,
activation, etc... vm_pageq.c relates to finding free pages and aquiring
exclusive access to a page queue (exclusivity part not yet implemented).
And the world still builds... :-)
- Move the lance_probe function to if_lnc.c.
- Support C-NET(98)S again.
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata) and nyan
No response from: Paul Richards
1. Add SA_IO_TIMEOUT as an option (4 minutes default) to cover reads,
writes, wfm, test unit ready.
2. Add internal SCSIOP_TIMEOUT (e.g., for mode sense) at 1 minute. This
should not require an option, but is cleaner to parameterize.
MFC after: 1 week
removed and a minimal number of changes to make it compile in the new
location.
# I have a fully converted on a disk that may be crashed. If it is
# crashed, I'll redo the work.
introduce a modified allocation mechanism for mbufs and mbuf clusters; one
which can scale under SMP and which offers the possibility of resource
reclamation to be implemented in the future. Notable advantages:
o Reduce contention for SMP by offering per-CPU pools and locks.
o Better use of data cache due to per-CPU pools.
o Much less code cache pollution due to excessively large allocation macros.
o Framework for `grouping' objects from same page together so as to be able
to possibly free wired-down pages back to the system if they are no longer
needed by the network stacks.
Additional things changed with this addition:
- Moved some mbuf specific declarations and initializations from
sys/conf/param.c into mbuf-specific code where they belong.
- m_getclr() has been renamed to m_get_clrd() because the old name is really
confusing. m_getclr() HAS been preserved though and is defined to the new
name. No tree sweep has been done "to change the interface," as the old
name will continue to be supported and is not depracated. The change was
merely done because m_getclr() sounds too much like "m_get a cluster."
- TEMPORARILY disabled mbtypes statistics displaying in netstat(1) and
systat(1) (see TODO below).
- Fixed systat(1) to display number of "free mbufs" based on new per-CPU
stat structures.
- Fixed netstat(1) to display new per-CPU stats based on sysctl-exported
per-CPU stat structures. All infos are fetched via sysctl.
TODO (in order of priority):
- Re-enable mbtypes statistics in both netstat(1) and systat(1) after
introducing an SMP friendly way to collect the mbtypes stats under the
already introduced per-CPU locks (i.e. hopefully don't use atomic() - it
seems too costly for a mere stat update, especially when other locks are
already present).
- Optionally have systat(1) display not only "total free mbufs" but also
"total free mbufs per CPU pool."
- Fix minor length-fetching issues in netstat(1) related to recently
re-enabled option to read mbuf stats from a core file.
- Move reference counters at least for mbuf clusters into an unused portion
of the cluster itself, to save space and need to allocate a counter.
- Look into introducing resource freeing possibly from a kproc.
Reviewed by (in parts): jlemon, jake, silby, terry
Tested by: jlemon (Intel & Alpha), mjacob (Intel & Alpha)
Preliminary performance measurements: jlemon (and me, obviously)
URL: http://people.freebsd.org/~bmilekic/mb_alloc/
Replace the a.out emulation of 'struct linker_set' with something
a little more flexible. <sys/linker_set.h> now provides macros for
accessing elements and completely hides the implementation.
The linker_set.h macros have been on the back burner in various
forms since 1998 and has ideas and code from Mike Smith (SET_FOREACH()),
John Polstra (ELF clue) and myself (cleaned up API and the conversion
of the rest of the kernel to use it).
The macros declare a strongly typed set. They return elements with the
type that you declare the set with, rather than a generic void *.
For ELF, we use the magic ld symbols (__start_<setname> and
__stop_<setname>). Thanks to Richard Henderson <rth@redhat.com> for the
trick about how to force ld to provide them for kld's.
For a.out, we use the old linker_set struct.
NOTE: the item lists are no longer null terminated. This is why
the code impact is high in certain areas.
The runtime linker has a new method to find the linker set
boundaries depending on which backend format is in use.
linker sets are still module/kld unfriendly and should never be used
for anything that may be modular one day.
Reviewed by: eivind
- Replace some very poorly thought out API hacks that should have been
fixed a long while ago.
- Provide some much more flexible search functions (resource_find_*())
- Use strings for storage instead of an outgrowth of the rather
inconvenient temporary ioconf table from config(). We already had a
fallback to using strings before malloc/vm was running anyway.
This work was based on kame-20010528-freebsd43-snap.tgz and some
critical problem after the snap was out were fixed.
There are many many changes since last KAME merge.
TODO:
- The definitions of SADB_* in sys/net/pfkeyv2.h are still different
from RFC2407/IANA assignment because of binary compatibility
issue. It should be fixed under 5-CURRENT.
- ip6po_m member of struct ip6_pktopts is no longer used. But, it
is still there because of binary compatibility issue. It should
be removed under 5-CURRENT.
Reviewed by: itojun
Obtained from: KAME
MFC after: 3 weeks
is usually (always?) used in expressions like (KTR_COMPILE & KTR_FOO).
Defining it as KTR_INTR|KTR_PROC gave the wrong value in approximately
8497 places according to error output for compiling LINT.
memory I/O space. Otherwise, our resource allocation system might
mistakenly assign pccard, plug and play devices or other things
addresses that conflict with ROMs.
I cleaned up his code a little from the submited driver: style(9)
issues, commentary on why something that looks incorrect really is
correct. Also noted that while a checksum field is defined for the
ROMs, enough common hardware neglects it to make it not worthwhile
checking.
Submitted by: Nikolai Saoukh <nms@otdel-1.org>
PR: 22078
This closes a minor information leak which allows a remote observer to
determine the rate at which the machine is generating packets, since the
default behaviour is to increment a counter for each packet sent.
Reviewed by: -net
Obtained from: OpenBSD
gigabit ethernet controller chip. This device is used on some
fiber optic gigE cards from SMC, D-Link and Addtron. Jumbograms and
TCP/IP checksum offload on receive are supported. Hardware VLAN
filtering is not, because it doesn't play well with our existing
VLAN code. Also add manual page.
There is a 4.x version of this driver available at
http://www.freebsd.org/~wpaul/Level1/4.x if anyone feels adventurous
and wants to test it. I still need to do performance testing and
tuning with this device.
(For my next trick, I will make the 3Com 3cR990 sit up and beg.)
Add a CAPI (hardware independent) driver i4bcapi(4) and hardware driver
iavc (4) to support active CAPI-based BRI and PRI cards (currently AVM
B1 and T1 cards) to isdn4bsd.
systems were repo-copied from sys/miscfs to sys/fs.
- Renamed the following file systems and their modules:
fdesc -> fdescfs, portal -> portalfs, union -> unionfs.
- Renamed corresponding kernel options:
FDESC -> FDESCFS, PORTAL -> PORTALFS, UNION -> UNIONFS.
- Install header files for the above file systems.
- Removed bogus -I${.CURDIR}/../../sys CFLAGS from userland
Makefiles.
soon attach directly to pcic rather than the kludge pci-pcic device we
have now.
In some ways, this is similar to the work PAO3 did to try to support
cardbus bridges. In some ways different. This and future commits
will be taking from the spirit of many of those changes. pcicvar.h is
completely different from the pcicvar.h that appeared in PAO3, but
similar in concept.
If for some reason DEVFS is undesired, the "NODEVFS" option is
needed now.
Pending any significant issues, DEVFS will be made mandatory in
-current on july 1st so that we can start reaping the full
benefits of having it.
of the pcic class of devices. Go ahead and move it to the "usual"
place. I say "usual" in quotes since it isn't exactly right (not in
dev/blah), but it is closer than before.
and DP83821 gigabit ethernet MAC chips and the NatSemi DP83861 10/100/1000
copper PHY. There are a whole bunch of very low cost cards available with
this chipset selling for $150USD or less. This includes the SMC9462TX,
D-Link DGE-500T, Asante GigaNIX 1000TA and 1000TPC, and a couple cards
from Addtron.
This chip supports TCP/IP checksum offload, VLAN tagging/insertion.
2048-bit multicast filter, jumbograms and has 8K TX and 32K RX FIFOs.
I have not done serious performance testing with this driver. I know
it works, and I want it under CVS control so I can keep tabs on it.
Note that there's no serious mutex stuff in here yet either: I need
to talk more with jhb to figure out the right way to do this. That
said, I don't think there will be any problems.
This driver should also work on the alpha. It's not turned on in
GENERIC.
This driver supports PCI Xr-based and ISA Xem Digiboard cards.
dgm will go away soon if there are no problems reported. For now,
configuring dgm into your kernel warns that you should be using
digi. This driver is probably close to supporting Xi, Xe and Xeve
cards, but I wouldn't expect them to work properly (hardware
donations welcome).
The digi_* pseudo-drivers are not drivers themselves but contain
the BIOS and FEP/OS binaries for various digiboard cards and are
auto-loaded and auto-unloaded by the digi driver at initialisation
time. They *may* be configured into the kernel, but waste a lot
of space if they are. They're intended to be left as modules.
The digictl program is (mainly) used to re-initialise cards that
have external port modules attached such as the PC/Xem.
been made machine independent and various other adjustments have been made
to support Alpha SMP.
- It splits the per-process portions of hardclock() and statclock() off
into hardclock_process() and statclock_process() respectively. hardclock()
and statclock() call the *_process() functions for the current process so
that UP systems will run as before. For SMP systems, it is simply necessary
to ensure that all other processors execute the *_process() functions when the
main clock functions are triggered on one CPU by an interrupt. For the alpha
4100, clock interrupts are delievered in a staggered broadcast fashion, so
we simply call hardclock/statclock on the boot CPU and call the *_process()
functions on the secondaries. For x86, we call statclock and hardclock as
usual and then call forward_hardclock/statclock in the MD code to send an IPI
to cause the AP's to execute forwared_hardclock/statclock which then call the
*_process() functions.
- forward_signal() and forward_roundrobin() have been reworked to be MI and to
involve less hackery. Now the cpu doing the forward sets any flags, etc. and
sends a very simple IPI_AST to the other cpu(s). AST IPIs now just basically
return so that they can execute ast() and don't bother with setting the
astpending or needresched flags themselves. This also removes the loop in
forward_signal() as sched_lock closes the race condition that the loop worked
around.
- need_resched(), resched_wanted() and clear_resched() have been changed to take
a process to act on rather than assuming curproc so that they can be used to
implement forward_roundrobin() as described above.
- Various other SMP variables have been moved to a MI subr_smp.c and a new
header sys/smp.h declares MI SMP variables and API's. The IPI API's from
machine/ipl.h have moved to machine/smp.h which is included by sys/smp.h.
- The globaldata_register() and globaldata_find() functions as well as the
SLIST of globaldata structures has become MI and moved into subr_smp.c.
Also, the globaldata list is only available if SMP support is compiled in.
Reviewed by: jake, peter
Looked over by: eivind
We are way too inconsistent with our setting of the "schg" flag, and in
our default install, it doesn't really offer any additional security.
Reviewed by: arch@
interfaces and functionality intended for use during correctness and
regression testing. Features enabled by "options REGRESSION" may
in and of themselves introduce security or correctness problems if
used improperly, and so are not intended for use in production
systems, only in testing environments.
Obtained from: TrustedBSD Project
Parag Patel did all of the grunt work, so he gets the credit.
Register definitions and actions inferred from a Linux driver,
so Intel also gets some 'credit'.
the main benefit this gives for now is that via686 audio devices on
motherboards with ac97 codecs that do not support vra will be able to use
sample rates other than 48khz.
Add simple "xlat" converter which performs 8to8 table based conversion.
Unicode converter will be added in the near future.
Reviewed by: silence on arch@
Files placement reviewed by: bde
Obtained from: smbfs
- Introduce lock classes and lock objects. Each lock class specifies a
name and set of flags (or properties) shared by all locks of a given
type. Currently there are three lock classes: spin mutexes, sleep
mutexes, and sx locks. A lock object specifies properties of an
additional lock along with a lock name and all of the extra stuff needed
to make witness work with a given lock. This abstract lock stuff is
defined in sys/lock.h. The lockmgr constants, types, and prototypes have
been moved to sys/lockmgr.h. For temporary backwards compatability,
sys/lock.h includes sys/lockmgr.h.
- Replace proc->p_spinlocks with a per-CPU list, PCPU(spinlocks), of spin
locks held. By making this per-cpu, we do not have to jump through
magic hoops to deal with sched_lock changing ownership during context
switches.
- Replace proc->p_heldmtx, formerly a list of held sleep mutexes, with
proc->p_sleeplocks, which is a list of held sleep locks including sleep
mutexes and sx locks.
- Add helper macros for logging lock events via the KTR_LOCK KTR logging
level so that the log messages are consistent.
- Add some new flags that can be passed to mtx_init():
- MTX_NOWITNESS - specifies that this lock should be ignored by witness.
This is used for the mutex that blocks a sx lock for example.
- MTX_QUIET - this is not new, but you can pass this to mtx_init() now
and no events will be logged for this lock, so that one doesn't have
to change all the individual mtx_lock/unlock() operations.
- All lock objects maintain an initialized flag. Use this flag to export
a mtx_initialized() macro that can be safely called from drivers. Also,
we on longer walk the all_mtx list if MUTEX_DEBUG is defined as witness
performs the corresponding checks using the initialized flag.
- The lock order reversal messages have been improved to output slightly
more accurate file and line numbers.
Some of the major changes include:
- The SCSI error handling portion of cam_periph_error() has
been broken out into a number of subfunctions to better
modularize the code that handles the hierarchy of SCSI errors.
As a result, the code is now much easier to read.
- String handling and error printing has been significantly
revamped. We now use sbufs to do string formatting instead
of using printfs (for the kernel) and snprintf/strncat (for
userland) as before.
There is a new catchall error printing routine,
cam_error_print() and its string-based counterpart,
cam_error_string() that allow the kernel and userland
applications to pass in a CCB and have errors printed out
properly, whether or not they're SCSI errors. Among other
things, this helped eliminate a fair amount of duplicate code
in camcontrol.
We now print out more information than before, including
the CAM status and SCSI status and the error recovery action
taken to remedy the problem.
- sbufs are now available in userland, via libsbuf. This
change was necessary since most of the error printing code
is shared between libcam and the kernel.
- A new transfer settings interface is included in this checkin.
This code is #ifdef'ed out, and is primarily intended to aid
discussion with HBA driver authors on the final form the
interface should take. There is example code in the ahc(4)
driver that implements the HBA driver side of the new
interface. The new transfer settings code won't be enabled
until we're ready to switch all HBA drivers over to the new
interface.
src/Makefile.inc1,
lib/Makefile: Add libsbuf. It must be built before libcam,
since libcam uses sbuf routines.
libcam/Makefile: libcam now depends on libsbuf.
libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the
sbuf sources from sys/kern.
bsd.libnames.mk: Add LIBSBUF.
camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically
linked, we can't depend on the dynamic linker
to pull in libsbuf.
camcontrol.c: Use cam_error_print() instead of checking for
CAM_SCSI_STATUS_ERROR on every failed CCB.
sbuf.9: Change the prototypes for sbuf_cat() and
sbuf_cpy() so that the source string is now a
const char *. This is more in line wth the
standard system string functions, and helps
eliminate warnings when dealing with a const
source buffer.
Fix a typo.
cam.c: Add description strings for the various CAM
error status values, as well as routines to
look up those strings.
Add new cam_error_string() and
cam_error_print() routines for userland and
the kernel.
cam.h: Add a new CAM flag, CAM_RETRY_SELTO.
Add enumerated types for the various options
available with cam_error_print() and
cam_error_string().
cam_ccb.h: Add new transfer negotiation structures/types.
Change inq_len in the ccb_getdev structure to
be "reserved". This field has never been
filled in, and will be removed when we next
bump the CAM version.
cam_debug.h: Fix typo.
cam_periph.c: Modularize cam_periph_error(). The SCSI error
handling part of cam_periph_error() is now
in camperiphscsistatuserror() and
camperiphscsisenseerror().
In cam_periph_lock(), increase the reference
count on the periph while we wait for our lock
attempt to succeed so that the periph won't go
away while we're sleeping.
cam_xpt.c: Add new transfer negotiation code. (ifdefed
out)
Add a new function, xpt_path_string(). This
is a string/sbuf analog to xpt_print_path().
scsi_all.c: Revamp string handing and error printing code.
We now use sbufs for much of the string
formatting code. More of that code is shared
between userland the kernel.
scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly
useful in the first place.
Add a new error action, SS_REQSENSE. (Send a
request sense and then retry the command.)
This is useful when the controller hasn't
performed autosense for some reason.
Change the default actions around a bit.
scsi_cd.c,
scsi_da.c,
scsi_pt.c,
scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection
timeouts shouldn't be covered by a sense flag.
scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO.
Get rid of the last vestiges of a read/write
interface.
libkern/bsearch.c,
sys/libkern.h,
conf/files: Add bsearch.c, which is needed for some of the
new table lookup routines.
aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if
CAM_NEW_TRAN_CODE is defined.
sbuf.h,
subr_sbuf.c: Add the appropriate #ifdefs so sbufs can
compile and run in userland.
Change sbuf_printf() to use vsnprintf()
instead of kvprintf(), which is only available
in the kernel.
Change the source string for sbuf_cpy() and
sbuf_cat() to be a const char *.
Add __BEGIN_DECLS and __END_DECLS around
function prototypes since they're now exported
to userland.
kdump/mkioctls: Include stdio.h before cam.h since cam.h now
includes a function with a FILE * argument.
Submitted by: gibbs (mostly)
Reviewed by: jdp, marcel (libsbuf makefile changes)
Reviewed by: des (sbuf changes)
Reviewed by: ken
implementation is still experimental, and while fairly broadly tested,
is not yet intended for production use. Support for POSIX.1e ACLs on
UFS will not be MFC'd to RELENG_4.
This implementation works by providing implementations of VOP_[GS]ETACL()
for FFS, as well as modifying the appropriate access control and file
creation routines. In this implementation, ACLs are backed into extended
attributes; the base ACL (owner, group, other) permissions remain in the
inode for performance and compatibility reasons, so only the extended and
default ACLs are placed in extended attributes. The logic for ACL
evaluation is provided by the fs-independent kern/kern_acl.c.
o Introduce UFS_ACL, a compile-time configuration option that enables
support for ACLs on FFS (and potentially other UFS-based file systems).
o Introduce ufs_getacl(), ufs_setacl(), ufs_aclcheck(), which
respectively get, set, and check the ACLs on the passed vnode.
o Introduce ufs_sync_acl_from_inode(), ufs_sync_inode_from_acl() to
maintain access control information between inode permissions and
extended attribute data.
o Modify ufs_access() to load a file access ACL and invoke
vaccess_acl_posix1e() if ACLs are available on the file system
o Modify ufs_mkdir() and ufs_makeinode() to associate ACLs with newly
created directories and files, inheriting from the parent directory's
default ACL.
o Enable these new vnode operations and conditionally compiled code
paths if UFS_ACL is defined.
A few notes:
o This implementation is fairly widely tested, but still should be
considered experimental.
o Currently, ACLs are not exported via NFS, instead, the summarizing
file mode/etc from the inode is. This results in conservative
protection behavior, similar to the behavior of ACL-nonaware programs
acting locally.
o It is possible that underlying binary data formats associated with
this implementation may change. Consumers of the implementation
should expect to find their local configuration obsoleted in the
next few months, resulting in possible loss of ACL data during an
upgrade.
o The extended attributes interface and implementation is still
undergoing modification to address portable interface concerns, as
well as performance.
o Many applications do not yet correctly handle ACLs. In general,
due to the POSIX.1e ACL model, behavior of ACL-unaware applications
will be conservative with respects to file protection; some caution
is recommended.
o Instructions for configuring and maintaining ACLs on UFS will be
committed in the near future; in the mean time it is possible to
reference the README included in the last UFS ACL distribution
placed in the TrustedBSD web site:
http://www.TrustedBSD.org/downloads/
Substantial debugging, hardware, travel, or connectivity support for this
project was provided by: BSDi, Safeport Network Services, and NAI Labs.
Significant coding contributions were made by Chris Faulhaber. Additional
support was provided by Brian Feldman, Thomas Moestl, and Ilmar Habibulin.
Reviewed by: jedgar, keichii, mckusick, trustedbsd-discuss, freebsd-fs
Obtained from: TrustedBSD Project
that I removed in my last commit dealing with `make depend' bogons.
This commit has some races, but hopefully they are too short to matter.
Unfortuneatly, neither .newdep nor .olddep is removed by `make clean'.
Submitted by: bde
very specific scenarios, and now that we have had net.inet.tcp.blackhole for
quite some time there is really no reason to use it any more.
(first of three commits)
options UFS_EXTATTR and UFS_EXTATTR_AUTOSTART respectively. This change
reflects the fact that our EA support is implemented entirely at the
UFS layer (modulo FFS start/stop/autostart hooks for mount and unmount
events). This also better reflects the fact that [shortly] MFS will also
support EAs, as well as possibly IFS.
o Consumers of the EA support in FFS are reminded that as a result, they
must change kernel config files to reflect the new option names.
Obtained from: TrustedBSD Project
"options FFS_EXTATTR". When extended attribute auto-starting
is enabled, FFS will scan the .attribute directory off of the
root of each file system, as it is mounted. If .attribute
exists, EA support will be started for the file system. If
there are files in the directory, FFS will attempt to start
them as attribute backing files for attributes baring the same
name. All attributes are started before access to the file
system is permitted, so this permits race-free enabling of
attributes. For attributes backing support for security
features, such as ACLs, MAC, Capabilities, this is vital, as
it prevents the file system attributes from getting out of
sync as a result of file system operations between mount-time
and the enabling of the extended attribute. The userland
extattrctl tool will still function exactly as previously.
Files must be placed directly in .attribute, which must be
directly off of the file system root: symbolic links are
not permitted. FFS_EXTATTR will continue to be able
to function without FFS_EXTATTR_AUTOSTART for sites that do not
want/require auto-starting. If you're using the UFS_ACL code
available from www.TrustedBSD.org, using FFS_EXTATTR_AUTOSTART
is recommended.
o This support is implemented by adding an invocation of
ufs_extattr_autostart() to ffs_mountfs(). In addition,
several new supporting calls are introduced in
ufs_extattr.c:
ufs_extattr_autostart(): start EAs on the specified mount
ufs_extattr_lookup(): given a directory and filename,
return the vnode for the file.
ufs_extattr_enable_with_open(): invoke ufs_extattr_enable()
after doing the equililent of vn_open()
on the passed file.
ufs_extattr_iterate_directory(): iterate over a directory,
invoking ufs_extattr_lookup() and
ufs_extattr_enable_with_open() on each
entry.
o This feature is not widely tested, and therefore may contain
bugs, caution is advised. Several changes are in the pipeline
for this feature, including breaking out of EA namespaces into
subdirectories of .attribute (this is waiting on the updated
EA API), as well as a per-filesystem flag indicating whether
or not EAs should be auto-started. This is required because
administrators may not want .attribute auto-started on all
file systems, especially if non-administrators have write access
to the root of a file system.
Obtained from: TrustedBSD Project
rather than in silly places like "VFS Cluster debugging". People
should really be using COMPAT_LINUX instead of the linux module on
dynamic systems like -current.
Incredibally useful for debugging kernels using vmware.
Vmware com1 is diverted to one side, and gdb listens to the other side.
viola.. instant debugging sandbox on one system.
by the compiler. ie: char foo[0] comes out as 4 bytes on a.out, and
we depended on it coming out as 0 for the script version. :-(
Make double sure that genassym.o is built and nm'ed in elf mode.
(ia64 skipped since it is stuck on the linux toolchain and doesn't
understand the -elf switches)
depend on this. The linux ABI emulator tries to use it for some linux
binaries too. VM86 had a bigger cost than this and it was made default
a while ago.
Reviewed by: jhb, imp
