IPI_STOP IPIs.
- Change the i386 and amd64 MD IPI code to send an NMI if STOP_NMI is
enabled if an attempt is made to send an IPI_STOP IPI. If the kernel
option is enabled, there is also a sysctl to change the behavior at
runtime (debug.stop_cpus_with_nmi which defaults to enabled). This
includes removing stop_cpus_nmi() and making ipi_nmi_selected() a
private function for i386 and amd64.
- Fix ipi_all(), ipi_all_but_self(), and ipi_self() on i386 and amd64 to
properly handle bitmapped IPIs as well as IPI_STOP IPIs when STOP_NMI is
enabled.
- Fix ipi_nmi_handler() to execute the restart function on the first CPU
that is restarted making use of atomic_readandclear() rather than
assuming that the BSP is always included in the set of restarted CPUs.
Also, the NMI handler didn't clear the function pointer meaning that
subsequent stop and restarts could execute the function again.
- Define a new macro HAVE_STOPPEDPCBS on i386 and amd64 to control the use
of stoppedpcbs[] and always enable it for i386 and amd64 instead of
being dependent on KDB_STOP_NMI. It works fine in both the NMI and
non-NMI cases.
still works. Also, this is consistent with 'show pcpu' vs
'show allpcpu'. (And 'show allstacks' on OS X for that matter.)
- Add 'bt' as an alias for 'trace'. We already have a 'where' alias as
well, so this makes it easier for gdb-wired hands to work in ddb.
Ok'd by: rwatson (1)
Requested by: scottl (2)
MFC after: 1 day
{cos_sin}[f](x) so that x doesn't need to be reclassified in the
"kernel" functions to determine if it is tiny (it still needs to be
reclassified in the cosine case for other reasons that will go away).
This optimization is quite large for exponentially distributed x, since
x is tiny for almost half of the domain, but it is a pessimization for
uniformally distributed x since it takes a little time for all cases
but rarely applies. Arg reduction on exponentially distributed x
rarely gives a tiny x unless the reduction is null, so it is best to
only do the optimization if the initial x is tiny, which is what this
commit arranges. The imediate result is an average optimization of
1.4% relative to the previous version in a case that doesn't favour
the optimization (double cos(x) on all float x) and a large
pessimization for the relatively unimportant cases of lgamma[f][_r](x)
on tiny, negative, exponentially distributed x. The optimization should
be recovered for lgamma*() as part of fixing lgamma*()'s low-quality
arg reduction.
Fixed various wrong constants for the cutoff for "tiny". For cosine,
the cutoff is when x**2/2! == {FLT or DBL}_EPSILON/2. We round down
to an integral power of 2 (and for cos() reduce the power by another
1) because the exact cutoff doesn't matter and would take more work
to determine. For sine, the exact cutoff is larger due to the ration
of terms being x**2/3! instead of x**2/2!, but we use the same cutoff
as for cosine. We now use a cutoff of 2**-27 for double precision and
2**-12 for single precision. 2**-27 was used in all cases but was
misspelled 2**27 in comments. Wrong and sloppy cutoffs just cause
missed optimizations (provided the rounding mode is to nearest --
other modes just aren't supported).
is on AC power (i.e. not a laptop). This allows power_profile to run once
for desktop systems as well, for instance, to set C3 or CPU frequency.
MFC after: 2 weeks
promisc flag from the member interface, this is a no-op anyway since the
interface is disappearing. The driver may have already released
its resources such as miibus and this is likely to panic the kernel.
Submitted and tested by: Wojciech A. Koszek
MFC after: 2 weeks
that debug.mpsafenet be set to 0. It is still possible for dead locks to
occur while these filtering options are used due to the layering violation
inherent in their implementation.
Discussed: -current, rwatson, glebius
/etc/defaults/rc.conf will provide foo_program, too.
By specifying "command" we explicitly say that we're
going to rely on rc.subr(8) default methods, and
rc.subr(8) will take advantage of this soon.
The majority of our rc.d scripts already set "command"
if appropriate, so fix just the non-compliant handful.
from being reclaimed before it was wired. Use pmap_extract_and_hold()
instead of pmap_extract() and retain the hold on the page until it has been
wired.
