a PCB from a trapframe for purposes of unwinding the stack. The PCB
is used as the thread context and all but the thread that entered the
debugger has a valid PCB.
This function can also be used to create a context for the threads
running on the CPUs that have been stopped when the debugger got
entered. This however is not done at the time of this commit.
in which multiple (presumably different) debugger backends can be
configured and which provides basic services to those backends.
Besides providing services to backends, it also serves as the single
point of contact for any and all code that wants to make use of the
debugger functions, such as entering the debugger or handling of the
alternate break sequence. For this purpose, the frontend has been
made non-optional.
All debugger requests are forwarded or handed over to the current
backend, if applicable. Selection of the current backend is done by
the debug.kdb.current sysctl. A list of configured backends can be
obtained with the debug.kdb.available sysctl. One can enter the
debugger by writing to the debug.kdb.enter sysctl.
backend improves over the old GDB support in the following ways:
o Unified implementation with minimal MD code.
o A simple interface for devices to register themselves as debug
ports, ala consoles.
o Compression by using run-length encoding.
o Implements GDB threading support.
bootp -> BOOTP
bootp.nfsroot -> BOOTP_NFSROOT
bootp.nfsv3 -> BOOTP_NFSV3
bootp.compat -> BOOTP_COMPAT
bootp.wired_to -> BOOTP_WIRED_TO
- i.e. back out the previous commit. It's already possible to
pxeboot(8) with a GENERIC kernel.
Pointed out by: dwmalone
BOOTP -> bootp
BOOTP_NFSROOT -> bootp.nfsroot
BOOTP_NFSV3 -> bootp.nfsv3
BOOTP_COMPAT -> bootp.compat
BOOTP_WIRED_TO -> bootp.wired_to
This lets you PXE boot with a GENERIC kernel by putting this sort of thing
in loader.conf:
bootp="YES"
bootp.nfsroot="YES"
bootp.nfsv3="YES"
bootp.wired_to="bge1"
or even setting the variables manually from the OK prompt.
than as one-off hacks in various other parts of the kernel:
- Add a function maybe_preempt() that is called from sched_add() to
determine if a thread about to be added to a run queue should be
preempted to directly. If it is not safe to preempt or if the new
thread does not have a high enough priority, then the function returns
false and sched_add() adds the thread to the run queue. If the thread
should be preempted to but the current thread is in a nested critical
section, then the flag TDF_OWEPREEMPT is set and the thread is added
to the run queue. Otherwise, mi_switch() is called immediately and the
thread is never added to the run queue since it is switch to directly.
When exiting an outermost critical section, if TDF_OWEPREEMPT is set,
then clear it and call mi_switch() to perform the deferred preemption.
- Remove explicit preemption from ithread_schedule() as calling
setrunqueue() now does all the correct work. This also removes the
do_switch argument from ithread_schedule().
- Do not use the manual preemption code in mtx_unlock if the architecture
supports native preemption.
- Don't call mi_switch() in a loop during shutdown to give ithreads a
chance to run if the architecture supports native preemption since
the ithreads will just preempt DELAY().
- Don't call mi_switch() from the page zeroing idle thread for
architectures that support native preemption as it is unnecessary.
- Native preemption is enabled on the same archs that supported ithread
preemption, namely alpha, i386, and amd64.
This change should largely be a NOP for the default case as committed
except that we will do fewer context switches in a few cases and will
avoid the run queues completely when preempting.
Approved by: scottl (with his re@ hat)
wasn't actually clean, it was saving the xmm registers as left over by the
bios. fninit() doesn't clear those.
In fpudna(), instead of doing a fninit() and forgetting to load the initial
mxcsr, do a full fxrstor(&fpu_cleanstate). Otherwise we hand over whatever
random values are left in the xmm registers by the last user.
I'm not certain of whether this is excessive paranoia or not, but there was
an outright bug in neglecting to set the mxcsr value that caused awk to
SIGFPE in some case. Especially for Tim Robbins. :-)
i386 probably should do something about the mxcsr setings too.
Found by: tjr
devclass will be present even if the driver was disabled by a hint. Using
device_get_softc() provides the right info even if it's overkill.
Explained by: jhb
Otherwise, the setting of the PG_M bit by one processor could be lost if
another processor is simultaneously changing the PG_W bit.
Reviewed by: tegge@
present and thus that the PnPBIOS probe should be skipped instead of
having ACPI zero out the PnPBIOStable pointer.
- Make the PnPBIOStable pointer static to i386/i386/bios.c now that that is
the only place it is used.
pmap_extract() already does it.
In pmap_enter(), opa has already been masked so don't do it again.
Wrap a long line (recent transgression).
Use trunc_page() in pmap_mapdev() instead of anding with PG_FRAME, since
that is what we really meant.
Submitted by: alc (first item)
- export the rest of the cpu features (and amd's features).
- turn on EFER_NXE, depending on the NX amd feature bit
- reorg the identcpu stuff a bit in order to stop treating the
amd features as second class features (since it is now a primary feature
bit set) and make it easier to export.
