syscall arguments are collected before ptracestop() is called. As a
consequence, debugger cannot modify syscall or its arguments.
For i386, amd64 and ia32 on amd64 MD syscall(), reread syscall number
and arguments after ptracestop(), if debugger modified anything in the
process environment. Since procfs stopeven requires number of syscall
arguments in p_xstat, this cannot be solved by moving stop/trace point
before argument fetching.
Move the code to read arguments into separate function
fetch_syscall_args() to avoid code duplication. Note that ktrace point
for modified syscall is intentionally recorded twice, once with original
arguments, and second time with the arguments set by debugger.
PT_TO_SCX stop is executed after cpu_syscall_set_retval() already.
Reported by: Ali Polatel <alip exherbo org>
Briefly discussed with: jhb
MFC after: 3 weeks
. Properly allocate all IO space resources. These cards scatter their
IO addresses over a range of 0x1600 bytes, and they require an
additional address for "special interrupt handling".
. Implement the "special interrupt handling" per the GPIB-PCIIA
Technical Reference Manual; this was apparently not declared for the
clone card this driver has been originally implemented for, but it
turned out to be needed for both, an original NI brand PCII/PCIIA
card as well as the Axiom AX5488 clone.
. Add some diagnostic messages for various resource allocation etc.
failures during probe.
. Add some comments about the structure of the IO address space that
is used by these cards.
MFC after: 1 day
o Force the ebase to be 0x80000000 (the base that we're booted with may
need to be respected in the future).
o Initialize the clock early so we can initialize the console early
o use panic where we can now use it.
o Tag some code for parsing the boot records as belonging in the cavium sdk.
o remove support for booting on ancient boards...
# we make it further in bootstrapping now: interrupts being enabled in the
# uarts are now taking us out, it seems, for reasons unknown.
implementation of heartbeat interval was 2 but there was typo which
caused the heartbeat is sent approximately every 5 seconds. This
caused unintended controller reset by firmware because firmware
thought OS was crashed.
Submitted by: Floris Bos < info <> je-eigen-domein dot nl >
Tested by: Andrzej Tobola < ato <> iem dot pw dot edu dot pl >
Basically the msg ring interrupt was being re-enabled
inside a spinlock as the thread set it self up for rescheduling.
This won't work since inside the re-enable is another
spin lock.. which means on return from the reenable
the interrupts have been reenabled. Thus you would
get a clock int and end up panicing holding a spin
lock to long :-o
loopback.
- Change the meaning of "mix" OSS control. Now it controls loopback level,
according to comments in soundcard.h.
- Allow AD1981HD codecs to use playback mixer. Now driver should be able to
really use it.
- Fix bug in shared muters operation.
the Cavium version of the boot loader puts data just after &end, so
our rounding up to the next page in clearing memory overwrote their
data, which meant we'd get a lot of wrong values for parameters to the
system.
While I'm here, remove argc/argv parsing. Those values aren't passed
in via a0 and a1, so it was a guaranted panic on some boards.
larger than MAXPHYS + 1. This fixes a problem with cat(1) when it
uses a large I/O buffer.
Reported by: Fernando Apesteguía
Suggested by: jilles
Reviewed by: des
Approved by: trasz (mentor)
This avoids a bogus negative name cache entry from persisting forever
when another client creates an entry with the same name within the
same NFS server time of day clock tick. The mount option negnametimeo
can be used to override the default timeout interval on a
per-mount-point basis. Setting negnametimeo to 0 disables negative
name caching for the mount point.
I also fixed one obvious typo where args.timeo should be
args.maxgrouplist.
Submitted by: jhb (earlier version)
Reviewed by: jhb
MFC after: 2 weeks
register from the PCB.
Remove a couple of misleading comments while I am here. The comments are
misleading because they imply that interrupts will be enabled after the
status register is restored from the PCB. This is not the case because
the processor is at the exception level (SR_EXL is set).
Approved by: imp (mentor)
and deactivate_device
- Save state before attaching driver and restore it when
detaching
- Clear CLK bit after last bit of byte has been sent over
the bus providing falling edge for last byte in transfer
- Fix several places where CS0 was always assumed
- Add $FreeBSD$ to ar71xxreg.h
frames to be accepted while the driver is resetting the hardware.
This failure is generally observed when broadcast frames are received
during driver load and will generate "Unable to write CTX memory"
errors.
- Small changes to driver flags display.
convert its value. [1]
- Set default tm_nodes_max to min(pages + 3, UINT32_MAX). It's more
reasonable than the old four nodes per page (with page size 4096) because
non-empty regular files always use at least one page. This fixes possible
overflow in the calculation. [2]
- Don't allow more than tm_nodes_max nodes allocated in tmpfs_alloc_node().
PR: kern/138367
Suggested by: bde [1], Gleb Kurtsou [2]
Approved by: trasz (mentor)
stopped and debugger may modify or drop the signal. After the changes to
keep process-targeted signals on the process sigqueue, another thread
may note the old signal on the queue and act before the thread removes
changed or dropped signal from the process queue. Since process is
traced, it usually gets stopped. Or, if the same signal is delivered
while process was stopped, the thread may erronously remove it,
intending to remove the original signal.
Remove the signal from the queue before notifying the debugger. Restore
the siginfo to the head of sigqueue when signal is allowed to be
delivered to the debugee, using newly introduced KSI_HEAD ksiginfo_t
flag. This preserves required order of delivery. Always restore the
unchanged signal on the curthread sigqueue, not to the process queue,
since the thread is about to get it anyway, because sigmask cannot be
changed.
Handle failure of reinserting the siginfo into the queue by falling
back to sq_kill method, calling sigqueue_add with NULL ksi.
If debugger changed the signal to be delivered, use sigqueue_add()
with NULL ksi instead of only setting sq_signals bit.
Reported by: Gardner Bell <gbell72 rogers com>
Analyzed and first version of fix by: Tijl Coosemans <tijl coosemans org>
PR: 142757
Reviewed by: davidxu
MFC after: 2 weeks
Remove __gnu89_inline.
Now that we use C99 almost everywhere, just use C99-style in the pmap
code. Since the pmap code is the only consumer of __gnu89_inline, remove
it from cdefs.h as well. Because the flag was only introduced 17 months
ago, I don't expect any problems.
Reviewed by: alc
It was backed out, because it prevented us from building kernels using a
7.x compiler. Now that most people use 8.x, there is nothing that holds
us back. Even if people run 7.x, they should be able to build a kernel
if they run `make kernel-toolchain' or `make buildworld' first.
the parent wirless interface. If the user passed in a mac address or it was
autogenerated then flag this to avoid trashing it on update.
This will fix wlan+lagg in a post vap world.
