- Make the USB hardware skip PTDs which are not allocated.
- Peek host memory twice. Sometimes the PTD status is incorrectly
returned as zero.
- Ensure the host channel is always freed when software TD
is completing.
- Add correct configuration of interrupt polarity and type.
- Set CERR to 2 for asynchronous traffic to avoid having to
reactivate the PTD when a NAK token is received.
- Fix detection of STALL PID.
Sponsored by: DARPA, AFRL
physical addresses.
- Nuke the unused softc of emujoy(4).
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
MFC after: 3 days
Sponsored by: Bally Wulff Games & Entertainment GmbH
- Based on actual usage and on what Linux does, dummy_page.addr should
contain the physical bus address of the dummy page rather than its
virtual one. As a side-effect, correcting this bug fixes compilation
with PAE support enabled by getting rid of an inappropriate cast.
- Also based on actual usage of dummy_page.addr, theoretically Radeon
devices could do a maximum of 44-bit DMA. In reality, though, it is
more likely that they only support 32-bit DMA, at least that is what
radeon_gart_table_ram_alloc() sets up for, too. However, passing ~0
to drm_pci_alloc() as maxaddr parameter translates to 64-bit DMA on
amd64/64-bit machines. Thus, use BUS_SPACE_MAXSIZE_32BIT instead,
which the existing 32-bit DMA limits within the drm2 code spelled as
0xFFFFFFFF should also be changed to.
Reviewed by: dumbbell
MFC after: 1 week
Sponsored by: Bally Wulff Games & Entertainment GmbH
- Switch from timeout() to callout_*() for per-request timers.
- Use device_find_child() in the identify routine.
- Use device_printf() instead of passing device_get_nameunit() to
printf().
- Expand the SBP_LOCK coverage simplifying the locking.
- Uninline STAILQ_FOREACH_SAFE().
Tested by: sbruno
Netmap gets its own hardware-assisted virtual interface and won't take
over or disrupt the "normal" interface in any way. You can use both
simultaneously.
For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface
(note the 'n' prefix) in the hardware to accompany each cxl<N>
interface. These two ifnet's per port share the same wire but really
are separate interfaces in the hardware and software. Each gets its own
L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You
should run netmap on the 'n' interfaces only, that's what they are for.
With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port
of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now.
Single port receive is at 33Mpps but this is very much a work in
progress. I expect it to be closer to 40Mpps once done. In any case
the current effort can already saturate multiple 10G ports of a T5 card
at the smallest legal packet size. T4 gear is totally untested.
trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43🆎cd:ef
881.952141 main [1621] interface is ncxl0
881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0
881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0
881.962540 main [1804] mapped 334980KB at 0x801dff000
Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus.
10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43🆎cd:ef)
881.962562 main [1882] Sending 512 packets every 0.000000000 s
881.962563 main [1884] Wait 2 secs for phy reset
884.088516 main [1886] Ready...
884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1
884.088607 sender_body [996] start
884.093246 sender_body [1064] drop copy
885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec)
886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec)
887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec)
888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec)
889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec)
890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec)
891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec)
892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec)
893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec)
894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec)
895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec)
896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec)
...
Relnotes: Yes
Sponsored by: Chelsio Communications.
uart2: <Intel AMT - PM965/GM965 KT Controller> port 0x1830-0x1837
mem 0xfe024000-0xfe024fff irq 17 at device 3.3 on pci0
uart2: console (115200,n,8,1)
Tested as tty and serial console. Seems "fine"
- Put "_LE_" into the register access macros to indicate little endian
byte order is expected by the hardware.
- Avoid using the bounce buffer when not strictly needed. Try to move
data directly using bus-space functions first.
- Ensure we preserve the reserved bits in the power down mode
register. Else the hardware goes into a non-recoverable state.
- Always use 32-bit access when writing or reading registers or FIFOs,
because the hardware is 32-bit oriented and don't really understand 8-
and 16-bit access.
- Correct writes to the memory address register. There is no need to
shift the register offset.
- Correct interval for interrupt endpoints.
- Optimise 90ns internal memory buffer read delay.
- Rename PDT into PTD, which is how the datasheet writes it.
- Add missing programming for activating host controller PTDs.
Sponsored by: DARPA, AFRL
Idle priority is not even time-share, so if system is busy in any way,
those events may never be executed. Since in some cases system waits
for events processed by that thread, that may cause deadlocks.
"fatal firmware error" happens. Previously it was neccessary to reset
it manually, using "/etc/rc.d/netif restart".
Approved by: adrian@
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
"fatal firmware error" happens. Previously it was neccessary to reset
it manually, using "/etc/rc.d/netif restart".
Approved by: adrian@
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
direction isochronous transfers.
- Remove setting of fields which does not belong to the respective
TRBs. These fields are currently set as zero and this is more a
cosmetic change.
MFC after: 3 days
Submitted by: Horse Ma <HMa@wyse.com>
- Make sure TX/RX lists don't leak and are only allocated once.
- Fix off-by one transfer index computation.
- Give firmware loading more time.
MFC after: 3 days
be a race when using a single active queue for all transmit types.
- Last argument of usb_pause_mtx() is ticks and not milliseconds.
- Remove unused watchdog.
- Remove some unused fields from the RSU softc structure.
- Workaround usbd_transfer_start() recursion from inside of completion
callback.
MFC after: 3 days
- Need to set the pre-fetch memory address when reading the host memory.
- We currently assume that no endianness conversion is needed.
Sponsored by: DARPA, AFRL
ismt(4) supports the SMBus Message Transport controller found on Intel
C2000 series (Avoton) and S1200 series (Briarwood) Atom SoCs.
Sponsored by: Intel
Intel 40G Ethernet Controller XL710 Family. This is
the core driver, a VF driver called i40evf, will be
following soon. Questions or comments to myself or
my co-developer Eric Joyner. Cheers!
- Implement support for interrupt filters in the DWC OTG driver, to
reduce the amount of CPU task switching when only feeding the FIFOs.
- Add common spinlock to the USB bus structure.
MFC after: 2 weeks
platform code, it is expected these will be merged in the future when the
ARM code is more complete.
Until more boards can be tested only use this with the Raspberry Pi and
rrename the functions on the other SoCs.
Reviewed by: ian@
it doesn't leak through when the command structure is reused for a user
command without a data buffer.
PR: amd64/189668
Tested by: Pete Long <pete@nrth.org>
MFC after: 1 week
