The need for !! over (bool) pre-dates gcc 4.2, so go with the patch
as-submitted because the kernel tends to prefer that.
Suggested by: emaste@
Sponsored by: Netflix
Currently, mmc_fdt_gpio_get_{present,readonly} return all time true.
true ^ 100b = true
false ^ 100b = true
since that's done after promotion to integers. Use !! to convert
the bit to a bool before xor.
Reviewed by: imp@ (converted to (bool) to !! for portability)
Pull Request: https://github.com/freebsd/freebsd-src/pull/461
Update mmc_switch_status to ignore a few CRC errrors when asking for the
card status after setting the new rate with CMD6. Since the card may
take a little while to make the switch, it's possible we'll get a
communications error if we sent the command at the wrong time. Several
low end laptops needs this workaround as they have a window that seems
longer than other systems. This is known to fix at least the Acer Aspire
A114-32-P7E5.
Reviewed by: imp@, manu@
Differential Revision: https://reviews.freebsd.org/D24740
This allow us to powerup/down the card and enabling/disabling the
regulators if any.
Sponsored by: Diablotin Systems
Differential Revision: https://reviews.freebsd.org/D30292
This helper can be used to enable/disable the regulator and starting
the power sequence of sd/sdio/eMMC cards.
Sponsored by: Diablotin Systems
Differential Revision: https://reviews.freebsd.org/D30291
If a sd/emmc node have a pwrseq property parse it and get the corresponding
driver.
This can later be used to powerup/powerdown the SDIO card or eMMC.
Sponsored by: Diablotin Systems
Differential Revision: https://reviews.freebsd.org/D30289
This driver is used to power up sdio card or eMMC.
It handle the reset-gpio, clocks and needed delays for powerup/powerdown.
Sponsored by: Diablotin Systems
Differential Revision: https://reviews.freebsd.org/D30288
A lot more generic cam related things are done in mmc_sim so this simplify
the driver a lot.
Differential Revision: https://reviews.freebsd.org/D27487
Reviewed by: kibab
- limit maximum segment size to 2048 bytes. Although dwmmc supports a buffer
fragment with a maximum length of 4095 bytes, use the nearest lower power
of two as the maximum fragment size. Otherwise, busdma create excessive
buffer fragments.
- fix off by one error in computation of the maximum data transfer length.
- in addition, reserve two DMA descriptors that can be used by busdma
bouncing. The beginning or end of the buffer can be misaligned.
- Don’t ignore errors passed to bus_dmamap_load() callback function.
- In theory, a DMA engine may be running at time when next dma descriptor is
constructed. Create a full DMA descriptor before OWN bit is set.
MFC after: 2 weeks
Remove two debugging printfs, even if hidden under boot -v.
They seemed to be of debug nature and always spit onto the
console when running camcontrol devlist -v.
Reviewed by: manu
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D25962
If the fdt node doesn't have a cd-gpios properties or if the node is set
as non-removable we do not init the card detection timeout task as it is
useless so don't schedule it too.
MFC after: 1 month
X-MFC-With: r359924
the dts to find the supported speeds and the regulators.
Not all DTS have every settings properly defined so host controller
will still have to add some caps themselves.
It also add a mmc_fdt_gpio_setup function which will read the cd-gpios
property and register it as the CD pin.
If the pin support interrupts one will be registered and the cd_helper
function will be called.
If the pin doesn't support interrupts the internal taskqueue will poll
for change and call the same cd_helper function.
mmc_fdt_gpio_setup will also parse the wp-gpio property and MMC drivers
can know the write-protect pin value by calling the
mmc_fdt_gpio_get_readonly function.
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D23267
Each segment can be up to 4096 bytes in chain structure according to the
RK3399 TRM Part 2.
Set the buffers in full ring where the last one point to the first one.
Correctly reports the MMC_IVAR_MAX_DATA.
Use CACHE_LINE_SIZE for bus_dma alignment.
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D23894
The IVAR_MAX_DATA is supposed to have the number of descriptor X the mmc
block size and desc_count contain all this information + 1.
Reported by: phk
MFC after: 1 week
r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked).
Use it in preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Mark all obvious cases as MPSAFE. All entries that haven't been marked
as MPSAFE before are by default marked as NEEDGIANT
Approved by: kib (mentor, blanket)
Commented by: kib, gallatin, melifaro
Differential Revision: https://reviews.freebsd.org/D23718
BIO_READ and BIO_WRITE, we've handled this expanded syntax poorly in
drivers when the driver doesn't support a particular command. Do a
sweep and fix that.
Reported by: imp
Instead of first detaching the children(s) and then delete them,
use the device_delete_children function that does all of that.
MFC after: 1 month
Suggested by: ian
The driver used to always add the mmc device as it's child even
it no card was detected. Add a function that will detect if the
card is present or not and that will attach/detach the mmc device.
The function is either call on attach (as we won't have the interrupt
fired) or from two taskqueues. The first taskqueue will directly call
the function when the sdcard was present and is now removed and the other
one will delay a bit the attach when we didn't had a card and now have one.
This is mostly based on comments from the sdhci driver where it describe
a situation when the CD pin is detected before the others pins are connected.
MFC after: 1 month
This method will disable the regulators, clocks and assert the reset of
the module. It will also detach it's children (the mmc device) and release
it's resources.
While here enable the regulators on attach as we need them to power up
the sdcard or emmc.
MFC after: 1 month
o Remove All Rights Reserved from my notices
o imp@FreeBSD.org everywhere
o regularize punctiation, eliminate date ranges
o Make sure that it's clear that I don't claim All Rights reserved by listing
All Rights Reserved on same line as other copyright holders (but not
me). Other such holders are also listed last where it's clear.
Ignore only ENOENT (no DTS properties found) and ENODEV (driver not
present) non-zero return values from ext_resources.
Reviewed by: manu
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D22043
(resets, regulators, clocks) are not available.
Rely on a system initialization done by a bootloader in that cases.
This fixes operation on Terasic DE10-Pro (an Intel Stratix 10
development kit).
Sponsored by: DARPA, AFRL
If the bootloader enabled DMA we need to fully reset the DMA controller
otherwise we might have some stale data in it that provoke weird
behavior.
MFC after: 1 week
All MMCBR bridges have to implement all the MMCBR variables. This
implements them for everybody that currently doesn't.
A common routine for this should be written.
otherwise we panic.
dwmmc don't handle VCCQ (voltage for the IO line of the SD/eMMC) or
TIMING.
Add the needed accessor in the {read,write}_ivar functions.
Reviewed by: imp (previous version)
This allows replacing "sys/eventfilter.h" includes with "sys/_eventfilter.h"
in other header files (e.g., sys/{bus,conf,cpu}.h) and reduces header
pollution substantially.
EVENTHANDLER_DECLARE and EVENTHANDLER_LIST_DECLAREs were moved out of .c
files into appropriate headers (e.g., sys/proc.h, powernv/opal.h).
As a side effect of reduced header pollution, many .c files and headers no
longer contain needed definitions. The remainder of the patch addresses
adding appropriate includes to fix those files.
LOCK_DEBUG and LOCK_FILE_LINE_ARG are moved to sys/_lock.h, as required by
sys/mutex.h since r326106 (but silently protected by header pollution prior
to this change).
No functional change (intended). Of course, any out of tree modules that
relied on header pollution for sys/eventhandler.h, sys/lock.h, or
sys/mutex.h inclusion need to be fixed. __FreeBSD_version has been bumped.
SDIO command CMD53 (IO_RW_EXTENDED) allows data transfers using blocks of 1-2048 bytes,
with a maximum of 511 blocks per request.
Extend mmc_data structure to properly describe such requests,
and initialize the new fields in kernel and userland consumers.
No actual driver changes happen yet, these will follow in the separate changes.
Reviewed by: bz
Approved by: imp (mentor)
Differential Revision: https://reviews.freebsd.org/D19779
This is the common denominator for rockchip compatible from RK3288 to RK3399.
The other compatible are generally present in the DTS but the controllers
are the same.
MFC after: 1 week
transfer mode only (lost with r321385). [1]
- Similarly, don't try to set the power class on MMC devices that comply
to version 4.0 of the system specification but are operated in default/
legacy transfer or 1-bit bus mode as no power class is specified for
these cases. Trying to set a power class nevertheless resulted in an -
albeit harmless - error message.
PR: 231713 [1]
