Commit Graph

61 Commits

Author SHA1 Message Date
Matthew N. Dodd
e3bbbec2ca Announce ethernet MAC addresss in ether_ifattach(). 2004-03-14 07:12:25 +00:00
Maxime Henrion
aa0444ecdb Stop setting ifp->if_output to ether_output() since ether_ifattach()
does it for us already.
2004-03-11 14:04:59 +00:00
David E. O'Brien
a55a017f42 Don't use caddr_t in mchash(). Also use C99 spellings over BSD ones.
Requested by:	bde,imp
2003-12-08 07:54:15 +00:00
Sam Leffler
5120abbfb4 Drop the driver lock around calls to if_input to avoid a LOR when
the packets are immediately returned for sending (e.g.  when bridging
or packet forwarding).  There are more efficient ways to do this
but for now use the least intrusive approach.

Reviewed by:	imp, rwatson
2003-11-14 19:00:32 +00:00
David E. O'Brien
aa8255025a Try to create some sort of consistency in how the routings to find the
multicast hash are written.  There are still two distinct algorithms used,
and there actually isn't any reason each driver should have its own copy
of this function as they could all share one copy of it (if it grew an
additional argument).
2003-11-13 20:55:53 +00:00
Brooks Davis
9bf40ede4a Replace the if_name and if_unit members of struct ifnet with new members
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.

This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.

Approved By:	re (in principle)
Reviewed By:	njl, imp
Tested On:	i386, amd64, sparc64
Obtained From:	NetBSD (if_xname)
2003-10-31 18:32:15 +00:00
Warner Losh
19b7ffd1b8 Prefer new location of pci include files (which have only been in the
tree for two or more years now), except in a few places where there's
code to be compatible with older versions of FreeBSD.
2003-08-22 07:20:27 +00:00
Warner Losh
b84e866a18 Due to extreme bogusness in the pci bus layer, these drivers were
forced to do slightly bogus power state manipulation.  However, this
is one of those features that is preventing further progress, so mark
them as BURN_BIRDGES like I did for the drivers in sys/dev/...

This, like the other change, are a no-op unless you have BURN_BRIDGES
in your kernel.
2003-07-03 21:39:53 +00:00
Poul-Henning Kamp
9c96882e80 Remove unused variables.
Found by:       FlexeLint
2003-05-31 19:58:45 +00:00
Warner Losh
214073e5e4 Use newly minted device_is_attached rather than device_is_alive to see
if attach succeeded.  device_is_alive just tells us that probe
succeeded.  Since we were using it to do things like detach net
interfaces, this caused problems when there were errors in the attach
routine.

Symptoms of problem reported by: martin blapp
2003-04-21 18:34:04 +00:00
Nate Lawson
693f4477b1 Revise attach/detach resource cleanup
- Unconditionally call *_stop() if device is in the tree. This is to
  prevent callouts from happening after the device is gone. Checks for
  bus_child_present() should be added in the future to keep from touching
  potentially non-existent hardware in *_detach().  Found by iedowse@.
- Always check for and free miibus children, even if the device is not in
  the tree since some failure cases could have gotten here.
- Call ether_ifdetach() in the irq setup failure case
- ti(4), xl(4): move ifmedia_init() calls to the beginning of attach so
  that ifmedia_removeall() can be unconditionally called on detach. There
  is no way to detect whether ifmedia has been initialized without using
  a separate variable (as tl(4) does).
- Add comments to indicate assumptions of code path
2003-04-17 20:32:06 +00:00
Matthew N. Dodd
533294b956 - Don't call pci_enable_io() in drivers (unless needed for resume).
- Don't test memory/port status and emit an error message; the PCI
  bus code will do this now.
2003-04-16 03:16:57 +00:00
Matthew N. Dodd
f246e4a17f - Express hard dependencies on bus (pci, isa, pccard) and
network layer (ether).
- Don't abuse module names to facilitate ifconfig module loading;
  such abuse isn't really needed.  (And if we do need type information
  associated with a module then we should make it explicit and not
  use hacks.)
2003-04-15 06:37:30 +00:00
David E. O'Brien
8368cf8f75 Use __FBSDID rather than rcsid[]. 2003-04-03 21:36:33 +00:00
John Baldwin
59f47d29b7 Add missing ()'s so that these drivers all compile again.
Noticed by:	jake
Tested on:	i386 (compile)
2003-03-31 20:22:00 +00:00
Nate Lawson
54f1f1d1e6 Clean up locking and resource management for pci/if_*
- Remove locking of the softc in the attach method, instead depending on
  bus_setup_intr being at the end of attach (delaying interrupt enable until
  after ether_ifattach is called)
- Call *_detach directly in the error case of attach, depending on checking
  in detach to only free resources that were allocated.  This puts all
  resource freeing in one place, avoiding thinkos that lead to memory leaks.
- Add bus_child_present check to calls to *_stop in the detach method to
  be sure hw is present before touching its registers.
- Remove bzero softc calls since device_t should do this for us.
- dc: move interrupt allocation back where it was before.  It was unnecessary
  to move it.  This reverts part of 1.88
- rl: move irq allocation before ether_ifattach.  Problems might have been
  caused by allocating the irq after enabling interrupts on the card.
- rl: call rl_stop before ether_ifdetach
- sf: call sf_stop before ether_ifdetach
- sis: add missed free of sis_tag
- sis: check errors from tag creation
- sis: move dmamem_alloc and dmamap_load to happen at same time as tag creation
- sk: remove duplicate initialization of sk_dev
- ste: add missed bus_generic_detach
- ti: call ti_stop before ether_ifdetach
- ti: add missed error setting in ti_rdata alloc failure
- vr: add missed error setting in I/O, memory mapping cases
- xl: add missed error setting in I/O, memory mapping cases
- xl: remove multi-level goto on attach failure
- xl: move dmamem_alloc and dmamap_load to happen at same time as tag creation
- Calls to free(9) are unconditional because it is valid to call free with a
  null pointer.

Reviewed by:	imp, mdodd
2003-03-31 17:29:43 +00:00
Warner Losh
a163d034fa Back out M_* changes, per decision of the TRB.
Approved by: trb
2003-02-19 05:47:46 +00:00
Alfred Perlstein
44956c9863 Remove M_TRYWAIT/M_WAITOK/M_WAIT. Callers should use 0.
Merge M_NOWAIT/M_DONTWAIT into a single flag M_NOWAIT.
2003-01-21 08:56:16 +00:00
Martin Blapp
e808cf6260 When reading PHY regs over the i2c bus, the turnaround ACK bit
is read one clock edge too late. This bit is driven low by
slave (as any other input data bits from slave) when the clock
is LOW. The current code did read the bit after the clock was
driven high again.

Reviewed by:	luoqi
MFC after:	2 weeks
2003-01-10 08:09:58 +00:00
Poul-Henning Kamp
828463d085 Change the chip description from "DFE-550TX" to "DL10050".
The DL10050 chip is used on the 550TX and 580TX cards, probably
others as well.
2002-12-23 21:50:47 +00:00
Sam Leffler
9ef8b52020 o track either_ifattach/ether_ifdetach API changes
o use if_input for input packet processing
o don't strip the Ethernet header for input packets
o use BPF_* macros bpf tapping
o call ether_ioctl to handle default ioctl case
o track vlan changes

Reviewed by:	many
Approved by:	re
2002-11-14 23:49:09 +00:00
Alfred Perlstein
29f194457c Fix instances of macros with improperly parenthasized arguments.
Verified by: md5
2002-11-09 12:55:07 +00:00
Doug Ambrisko
724b7a2be2 Clarify comment to "Code borrowed from if_fxp.c" to deal with running
out of fragments.

Suggested by:	jhb
2002-09-18 21:32:48 +00:00
Doug Ambrisko
877b0861ca Only probe one PHY on the D-Link 580 version of the card (ie rev 0x12).
The 550 version is location at address 1 but since it works right we
let the code find whatever PHY it can.

Fix a fragment issue on TX.  If the number of frags are more then the
driver has allocated then bring all the frags together into one packet
and send it out.  Code derived from the fxp driver.

Tested and found by:	Francois Tigeot <francois.tigeot@nic.fr>
			Hellmuth Michaelis <hm@kts.org>

MFC after:	1 week
2002-09-11 21:26:22 +00:00
Bernd Walter
82026026e0 add missing \n to printf
Approved by:	gallatin (mentor)
2002-09-09 17:39:48 +00:00
Alfred Perlstein
e3d2833a26 style:
put return values on a line by themselves.
 fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
Doug Ambrisko
740f8a4472 Don't read the PCI config space during mii operations. Instead save whether
or not we have to limit the PHY detection in the softc structure.  Then
just check the flag.

Suggested by:	jdp
Reviewed by:	jdp
MFC after:	3 days
2002-08-19 16:54:26 +00:00
Doug Ambrisko
74495bcdab Revert change to detect multiply PHYs in mii code. There might be cases
when this is needed.  Work around bogus second PHY in the DFE-580 card
via a change in the if_ste.c driver.

Suggested by:	jdp
Reviewed by:	jdp
MFC after:	3 days
2002-08-16 23:19:16 +00:00
Doug Ambrisko
d44ef39e51 Fixes for the D-Link DFE-580 card.
This is pretty much fixes any issue I can find:
     -  Watchdog timeouts were due to starting the TX DMA engine
        before we had a packet ready for it.  So the first packet
        sent never got out only if we sent more then one packet
        at a time did the others make it out and not blow up.
        Of course reseting the chip then caused us not to transmit
        the first packet again ie. catch-22.  This required logic changes.
     -  Combine interrupts on TX packets being queued up.
     -  Don't keep running around the RX ring since we might get
        out of sync so only go around once per receive
     -  Let the RX engine recover via the poll interface which is
        similar to the TX interface.  This way the chip wakes
        up with no effort when we read enough packets.
     -  Do better hand-shaking on RX & TX packets so they don't
        start of to soon.
     -  Force a duplex setting when the link comes up after
        an ste_init or it will default to half-duplex and be
        really slow.  This only happens on subsequent ste_init.
        The first one worked.
     -  Don't call stat_update for every overflow.  We only monitor
        the collisions so the tick interval is good enough for that.
        Just read in the collision stats to minimize bus reads.
     -  Don't read the miibus every tick since it uses delays and
        delays are not good for performance.
     -  Tie link events directly to the miibus code so the port
        gets set correctly if someone changes the port settings.
     -  Reduce the extreme number of {R,T}FD's.  They would consume
        130K of kernel memory for each NIC.
     -  Set the TX_THRESH to wait for the DMA engine to complete
        before running the TX FIFO.  This hurts peak TX performance
        but under bi-directional load the DMA engine can't keep up
        with the FIFO.  Testing shows that we end up in the case
        anyways (a la dc(4) issues but worse since the RX engine hogs
	everything).
     -  When stopping the card do a reset since the reset verifies the
	card has stopped.  Otherwise on heavy RX load the RX DMA engine
	is still stuffing packets into memory.  If that happens after
	we free the DMA area memory bits get scribled in memory and
	bad things happen.

This card still has seemingly unfixable issues under heavy RX load in
which the card takes over the PCI bus.

Sponsored by:	Vernier Networks
MFC after:	1 week
2002-08-07 22:31:27 +00:00
John Baldwin
6008862bc2 Change callers of mtx_init() to pass in an appropriate lock type name. In
most cases NULL is passed, but in some cases such as network driver locks
(which use the MTX_NETWORK_LOCK macro) and UMA zone locks, a name is used.

Tested on:	i386, alpha, sparc64
2002-04-04 21:03:38 +00:00
Alfred Perlstein
e51a25f850 Remove __P. 2002-03-20 02:08:01 +00:00
Luigi Rizzo
268cc03905 Remove printf's on mbuf/cluster allocation failures. There are now
equivalent and less dangerous (rate limited) messages in
the mbuf allocation code.

MFC after: 3 days
2001-12-14 05:56:35 +00:00
Jonathan Lemon
cd62a9cb38 Do not call mii_pollstat() from within device tick routines; the status
information is updated by mii_tick().

Pointed out by: wpaul (a while back)
2001-09-29 19:28:31 +00:00
Bill Paul
645ed1a78b Fix a bug in the ste_setmulti() routine. The NIC has 4 16-bit multicast
hash registers, not 2 32-bit ones. This would prevent the multicasr filter
from being programmed correctly in some cases.
2001-08-23 18:22:55 +00:00
Bill Paul
75ff968cd5 Apply patch supplied by Jonathan Chen: use the correct arguments to
pci_enable_io(). We need to use SYS_RES_IOPORT/SYS_RES_MEMORY instead
of PCIM_CMD_PORTEN/PCIM_CMD_MEMEN.
2001-07-09 17:58:42 +00:00
Bill Paul
07f65363cd Big round of minor updates:
- Use pci_get_powerstate()/pci_set_powerstate() in all the other drivers
  that need them so we don't have to fiddle with the PCI power management
  registers directly.
- Use pci_enable_busmaster()/pci_enable_io() to turn on busmastering and
  PIO/memory mapped accesses.
- Add support to the RealTek driver for the D-Link DFE-530TX+ which has
  a RealTek 8139 with its own PCI ID. (Submitted by Jason Wright)
- Have the SiS 900/National DP83815 driver be sure to disable PME
  mode in sis_reset(). This apparently fixes a problem on some
  motherboards where the DP83815 chip fails to receive packets.
  (Submitted by Chuck McCrobie <mccrobie@cablespeed.com>)
2001-02-21 20:54:22 +00:00
Poul-Henning Kamp
6817526d14 Convert if_multiaddrs from LIST to TAILQ so that it can be traversed
backwards in the three drivers which want to do that.

Reviewed by:    mikeh
2001-02-06 10:12:15 +00:00
Poul-Henning Kamp
37d4006626 Another round of the <sys/queue.h> FOREACH transmogriffer.
Created with:   sed(1)
Reviewed by:    md5(1)
2001-02-04 16:08:18 +00:00
Poul-Henning Kamp
78d82c8c59 Use LIST_FOREACH() to traverse ifp->if_multiaddrs list, instead of
<sys/queue.h> implementation details.

Created with:   /usr/sbin/sed
Reviewed with:  /sbin/md5
2001-02-03 16:29:10 +00:00
Bosko Milekic
08812b3925 Implement MTX_RECURSE flag for mtx_init().
All calls to mtx_init() for mutexes that recurse must now include
the MTX_RECURSE bit in the flag argument variable. This change is in
preparation for an upcoming (further) mutex API cleanup.
The witness code will call panic() if a lock is found to recurse but
the MTX_RECURSE bit was not set during the lock's initialization.

The old MTX_RECURSE "state" bit (in mtx_lock) has been renamed to
MTX_RECURSED, which is more appropriate given its meaning.

The following locks have been made "recursive," thus far:
eventhandler, Giant, callout, sched_lock, possibly some others declared
in the architecture-specific code, all of the network card driver locks
in pci/, as well as some other locks in dev/ stuff that I've found to
be recursive.

Reviewed by: jhb
2001-01-19 01:59:14 +00:00
Bill Paul
031fc810ab Initialize/grab the mutex earlier in the attach phase, so that
bailing out to the fail: label where we release/destroy the mutex
will work without exploding.
2000-12-04 22:46:50 +00:00
Poul-Henning Kamp
db7e3af111 Remove unneeded #include <machine/clock.h> 2000-10-15 14:19:01 +00:00
Bill Paul
1e856a7b34 Use device_get_nameunit(dev) as the mutex string when calling
mtx_init() instead of hard-coded string constant. Also remember to do
the mutex changes to the ste driver, which I forgot in the first commit.
2000-10-13 18:35:49 +00:00
Archie Cobbs
21b8ebd926 Make all Ethernet drivers attach using ether_ifattach() and detach using
ether_ifdetach().

The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.

Reviewed by:	julian, freebsd-net
2000-07-13 22:54:34 +00:00
Peter Wemm
86b0a953e2 Use the correct register name. s/PCI_COMMAND_STATUS_REG/PCIR_COMMAND/ 2000-05-28 16:13:43 +00:00
Archie Cobbs
2e2de7f23f Move code to handle BPF and bridging for incoming Ethernet packets out
of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.

The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.

The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.

Reviewed by:	freebsd-net
2000-05-14 02:18:43 +00:00
Peter Wemm
95a1645553 Depend on miibus.
Note that if_aue doesn't strictly depend on usb because it uses the
method interface for calls rather than using internal symbols, and
because it's a child driver of usb and therefore will not try and do
anything unless the parent usb code is loaded at some point.  if_aue does
strictly depend on miibus as it will fail to link if it is missing.
2000-04-29 13:41:57 +00:00
Bill Paul
a2c195896a Spruce up the Sundance ST201 driver:
- Convert to using TX descritor polling similar to the xl driver (the
  ST201 is a clone of the 3c90xB chipset and offers the same transmit
  polling scheme). This should reduce TX overhad a little.

- Make sure to reset PHY when switching mode, as in the starfire driver.

- Fix instances of free() that should be contigfree().

- Remove dead code.
1999-12-07 20:14:42 +00:00
Bill Paul
98a229f65e As suggested by phk, unconditionalize BPF support in these drivers. Since
there are stubs compiled into the kernel if BPF support is not enabled,
there aren't any problems with unresolved symbols. The modules in /modules
are compiled with BPF support enabled anyway, so the most this will do is
bloat GENERIC a little.
1999-09-23 03:32:57 +00:00
Bill Paul
9e4c647c74 Tweak these for what I hope is the last time: change the DRIVER_MODULE()
declaration for the interface driver from "foo" to "if_foo" but leave the
declaration for the miibus attached to the interface driver alone. This
lets the internal module name be "if_foo" while still allowing the miibus
instances to attach to "foo."

This should allow ifconfig to autoload driver modules again without
breaking the miibus attach.
1999-09-22 06:08:11 +00:00