return -1000 and -10000 to establish a pecking order and we don't want
catch-all or match-all drivers to attach instead of them.
With this change poto(4) can be compiled into the kernel (or preloaded
from the loader), without impact.
(easily) without having to go to other drivers to change the
magical return values. This wouldn't be so bad if there were
proper defines for these constants.
In particular dev/acpica/acpi_pcib_pci.c returns -1000 as the
probe priority and it's expected that this driver gets to
attach over the common PCI bus drivers.
The "depends_on module" pragma can be used to declare a dependency on a
DTrace module, which for kernel probes corresponds to a KLD. Such
dependencies cannot be checked if the KLD is compiled into the kernel.
Therefore, allow a module dependency to be satisfied if either a kernel
module or a KLD with the specified name is loaded.
Differential Revision: https://reviews.freebsd.org/D2653
Reviewed by: gnn, rpaulo
Reported by: gnn
Without creating a LAW entry, any access to the NAND hangs the CPU.
The original intent was to add a quirk to map all of the RouterBoard's LBC
address space in one shot, which would fix it for both NAND and the CF, and
that's probably still in the cards. However, for now, this makes NAND usable
without a separate hack.
Things left before the RouterBoard can run standalone:
* Add partitions to the NAND (not specified by the FDT, which we currently
require).
* Create a YAFFS partition for the kernel. The Mikrotik boot loader requires a
4MB partition at the beginning of NAND, with a file called 'kernel' in the
root.
- MNTK_SUSPENDABLE is set in mnt_kern_flag, not mnt_flag.
- The lower layer of a unionfs mount is read-only, so the mount should
be suspendable iff the upper layer is suspendable.
- Remove a couple of superfluous comments.
Differential Revision: https://reviews.freebsd.org/D2714
Reviewed by: kib, mjg
Create a special resource (= device special file) for management
of tags and maps, as well as for mapping memory into the address
space. DMA resources are managed using the PROTO_IOC_BUSDMA ioctl.
Part 1 implements tag creation, derivation and destruction.
BUS_PROBE_HOOVER is. Drivers like proto(4), when compiled into the
kernel or preloaded, will render your system useless by virtue of
attaching to your PCI busses.
Return BUS_PROBE_GENERIC instead. It's just the next priority up
from BUS_PROBE_HOOVER. No other meaning has been give to its use.
While BUS_PROBE_DEFAULT seems like a better candidate, it's hard
not to think that there must be some reason why these drivers
return -10000 in the first place.
Differential Revision: D2705
code update, with supporting changes in the CORE. Changes for the extended
media types, VF driver has virtual channel protocol changes, and some
register use corrections. This software change should be coordinated with
Firmware updates to your hardware, contact your support channels for that.
MFC after: 1 week
after decoding the instruction matches the one provided by hardware.
Prior to r283293 'vie->num_valid' used to contain the actual length of
the instruction whereas now it contains the maximum instruction length
possible. This introduced a bug when calculating a RIP-relative base address.
Fix this by using 'vie->num_processed' rather than 'vie->num_valid' as the
length of the emulated instruction.
Reported and tested by: tychon
MFC after: 1 week
interpreter list to avoid the problem of holding a non-sleep lock during
a page fault as reported by witness. In addition, it consistently uses
memset()/memcpy() instead of bzero()/bcopy() except in the case where
bcopy() is required (i.e. overlapping copy).
Differential Revision: https://reviews.freebsd.org/D2123
Submitted by: sson
MFC after: 2 weeks
Relnotes: Yes
A hole block pointer can be encountered at any level and the hole
can cover multiple data blocks, but we are reading the data blocks
one by one, so we care only about the current one.
PR: 199804
Reported by: Toomas Soome <tsoome@me.com>
Submitted by: Toomas Soome <tsoome@me.com> (earlier version)
Tested by: Toomas Soome <tsoome@me.com>
MFC after: 11 days
This is done if the installation mode is not requested or auto-detected.
This is useful when a kernel has to be loaded from multiple disks.
For example from a RAID-Z pool or a ZFS pool with multiple top level
vdevs.
Differential Revision: https://reviews.freebsd.org/D2723
Reviewed by: neel
MFC after: 8 days
The intel 7260 driver under development requires this - the scans come
in as normal frames but with the frequency provided. The correct method
is to have the driver provide flags (so we can determine if it's 11b
or 11g); this will have to do in the meantime.
Without this, the channel found is 11b, and no ERP (ie "11g") bits
are negotiated with the AP.
This allows the 7260 in 2ghz mode to operate in 11bg, rather than
just 11b.
Tested:
* intel 7260 driver, 11bg channels
