o Properly use rman(9) to manage resources. This eliminates the
need to puc-specific hacks to rman. It also allows devinfo(8)
to be used to find out the specific assignment of resources to
serial/parallel ports.
o Compress the PCI device "database" by optimizing for the common
case and to use a procedural interface to handle the exceptions.
The procedural interface also generalizes the need to setup the
hardware (program chipsets, program clock frequencies).
o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by
default and non-serdev devices are handled by the bus.
o Use the serdev I/F to collect interrupt status and to handle
interrupts across ports in priority order.
o Sync the PCI device configuration to include devices found in
NetBSD and not yet merged to FreeBSD.
o Add support for Quatech 2, 4 and 8 port UARTs.
o Add support for a couple dozen Timedia serial cards as found
in Linux.
This driver was generously developed and donated by Highpoint.
It is enabled for i386 only at the moment. I will enable it for amd64
shortly.
Obtained from: HighPoint Technologies, Inc.
o Add the scc(4) manpage to the build.
o Update the uart(4) manpage to account for scc(4).
o Update the uart(4) module build to include support for scc(4).
controllers typically have multiple channels and support a number
of serial communications protocols. The scc(4) driver is itself
an umbrella driver that delegates the control over each channel
and mode to a subordinate driver (like uart(4)).
The scc(4) driver supports the Siemens SAB 82532 and the Zilog
Z8530 and replaces puc(4) for these devices.
is derived from the phrase 'MegaRAID Firmware Interface' used by LSI. This
driver provides a block interface to logical disks on the card and a minimal
management device. It is MPSAFE, INTR_FAST, and 64-bit capable.
Thanks to Dell for providing hardware to test with and IronPort for
sponsoring the work.
Sponsored by: Dell, Ironport
MFC After: 3 days
- <netipx> headers [1]
- IPX library (libipx)
- IPX support in ifconfig(8)
- IPXrouted(8)
- new MK_NCP option
New MK_NCP build option controls:
- <netncp> and <fs/nwfs> headers
- NCP library (libncp)
- ncplist(1) and ncplogin(1)
- mount_nwfs(8)
- ncp and nwfs kernel modules
User knobs: WITHOUT_IPX, WITHOUT_IPX_SUPPORT, WITHOUT_NCP.
[1] <netsmb/netbios.h> unconditionally uses <netipx> headers
so they are still installed. This needs to be dealt with.
which is normal for own files of a device driver.
DEV_FOO should be used if an unrelated kernel file needs to know of
the `foo' driver's static presence. Obviously, module source files
should never use DEV_*.
enabled by default in NETSMB and smbfs.ko.
With the most of modern SMB providers requiring encryption by
default, there is little sense left in keeping the crypto part
of NETSMB optional at the build time.
This will also return smbfs.ko to its former properties users
are rather accustomed to.
Discussed with: freebsd-stable, re (scottl)
Not objected by: bp, tjr (silence)
MFC after: 5 days
into a separate module. Accordingly, convert the option into a device
named similarly.
Note for MFC: Perhaps the option should stay in RELENG_6 for POLA reasons.
Suggested by: scottl
Reviewed by: cokane
MFC after: 5 days
and want to have crypto support loaded as KLD. By moving zlib to separate
module and adding MODULE_DEPEND directives, it is possible to use such
configuration without complication. Otherwise, since IPSEC is linked with
zlib (just like crypto.ko) you'll get following error:
interface zlib.1 already present in the KLD 'kernel'!
Approved by: cognet (mentor)
Otherwise a kernel build would break in the coda5 module if the main
kernel conf file enabled CODA_COMPAT_5, too. Redefined symbols are
strictly disallowed by -Werror.
To overcome this issue, introduce a different symbol indicating coda5
build, CODA5_MODULE, and translate it to CODA_COMPAT_5 appropriately
in /sys/coda/coda.h.
MFC after: 3 days
inside !if defined(KERNBUILDDIR).
Utilize the fact the module will support all frames by default --
it needs no ETHER_* options unless some frames need to be disabled.
Fix the comment respectively.
Don't forget to create fake opt_ef.h if no ETHER_* are set.
MFC after: 3 days
More info regarding these nics can be found at http://www.myri.com.
Please note that the files
sys/dev/myri10ge/{mcp_gen_header.h,myri10ge_mcp.h} are internally
shared between all our drivers (solaris, macosx, windows, linux, etc).
I'd like to keep these files unchanged, so I can just import newer
versions of them when the firmware API/ABI changes. This means I'm
stuck with some of the crazy-long #define names, and possibly
non-style(9) characteristics of these files.
Many thanks to mlaier for doing firmware(9) just as I
needed it, and to scottl for his helpful review.
Reviewed by: scottl, glebius
Sponsored by: Myricom Inc.
Without CODA_COMPAT_5, it would be equivalent to the plain coda
module. Therefore just add -DCODA_COMPAT_5 to CFLAGS instead of
fiddling with opt_coda.h. This is particularly important when
the module is built along with the kernel and CODA_COMPAT_5 isn't
in the kernel conf file (and so not in opt_coda.h either).
MFC after: 3 days
nfs_diskless.c if NFS_ROOT is in effect, e.g., present
in the kernel config file. Otherwise the built module
won't load due to an undefined reference to nfs_setup_diskless.
MFC after: 3 days
to work with ipmitools. It works with other tools that have an OpenIPMI
driver interface. The port will need to get updated to used this.
I have not implemented the IPMB mode yet so ioctl's for that don't
really do much otherwise it should work like the OpenIPMI version.
The ipmi.h definitions was derived from the ipmitool header file.
The bus attachments are done for smbios and pci/smbios. Differences
in bus probe order for modules/static are delt with. ACPI attachment
should be done.
This drivers registers with the watchdod(4) interface
Work to do:
- BT interface
- IPMB mode
This has been tested on Dell PE2850, PE2650 & PE850 with i386 & amd64
kernel.
I will link this into the build on next week.
Tom Rhodes, helped me with the man page.
Sponsored by: IronPort Systems Inc.
Inspired from: ipmitool & Linux
