Use the special LUNLEN_SINGLE_LEVEL constant for
post Rev A4 hardware for single byte luns. Without
this change, Rev B hardware would place the single
byte of lun data in byte 0 of the lun structure when
it should be in byte 1. Since there are few if any
devices on the market that support multiple luns in
target mode, the corrupted lun field (which was only
corrupted for non-zero luns) wasn't hurting us.
Approved by: re (rwatson)
aic79xx.h:
aic79xx.reg:
Return the SCB_TAG field to 16byte alignment.
It seems that on some PCI systems, SCBs are not
transferred correctly to the controller with
the previous placement of the SCB_TAG field.
Approved by: re (rwatson)
865. The APSIZE register has a variable-sized field of enabled bits.
To figure out how many bits a specific host bridge supports, write the
maximum width and see how many bits are set in the hardware. We then
use this mask for setting and getting the aperture size. Prior to this,
the agp(4) driver would treat an aperture size of 256 MB as 128 MB and
would not allocate enough physical memory for the GART as a result.
MFC after: 3 days
Sponsored by: The Weather Channel
Approved by: re (rwatson)
BUS_DMASYNC_ definitions remain as before. The does not change the ABI,
and reverts the API to be a bit more compatible and flexible. This has
survived a full 'make universe'.
Approved by: re (bmah)
aic79xx.c:
In ahd_handle_ign_wide_residue():
o Use SCB_XFERLEN_ODD SCB field to determine transfer
"oddness" rather than the DATA_COUNT_ODD logic.
SCB_XFERLEN_ODD is toggled on every ignore wide
residue message so that multiple ignore wide residue
messages for the same transaction are properly supported.
o If the sg list has been exausted, the sequencer
doesn't bother to update the residual data count
since it is known to be zero. Perform the zeroing
manually before calculating the remaining data count.
o Use multibyte in/out macros instead of shifting/masking
by hand.
aic79xx_inline.h:
In ahd_setup_scb_common(), setup the SCB_XFERLEN_ODD field.
aic79xx.reg:
Use the SCB_TASK_ATTRIBUTE field as a bit field in the
non-packetized case. We currently only define one bit,
SCB_XFERLEN_ODD.
Remove the ODD_SEG bit field that was used to carry the odd
transfer length information through the SG cache. This
is obviated by SCB_XFERLEN_ODD field.
Remove the DATA_COUNT_ODD scratch ram byte that was used
dynamicaly compute data transfer oddness. This is obviated
by SCB_XFERLEN_ODD field.
aic79xx.seq:
Remove all updates to the DATA_COUNT_ODD scratch ram field.
Remove all uses of ODD_SEG. These two save quite a few
sequencer instructions.
Use SCB_XFERLEN_ODD to validate the end of transfer
ignore wide residue message case.
aic7xxx.c:
In ahc_handle_ign_wide_residue():
o Use SCB_XFERLEN_ODD SCB field to determine transfer
"oddness" rather than the DATA_COUNT_ODD logic.
SCB_XFERLEN_ODD is toggled on every ignore wide
residue message so that multiple ignore wide residue
messages for the same transaction are properly supported.
o If the sg list has been exausted, the sequencer
doesn't bother to update the residual data count
since it is known to be zero. Perform the zeroing
manually before calculating the remaining data count.
o Ensure that SG_LIST_NULL is cleared in the
residual sg pointer for "mid-transfer" ignore
wide residue cases.
o Use multibyte in/out macros instead of shifting/masking
by hand.
aic7xxx.h:
Modify the SCB_GET_LUN() macro to mask the lun hardware
SCB field with LID. This leaves two bits in the LUN
field that can be used for other purposes.
aic7xxx.reg:
Change LID to be 0x3F. This is the maximum supported
lun size for non-packetized SCSI. Map the top bit
of the lun to SCB_XFERLEN_ODD. The host must set
this bit whenever a transfer is an odd length.
Remove the ODD_SEG bit field that was used to carry the odd
transfer length information through the SG cache. This
is obviated by SCB_XFERLEN_ODD field.
Remove the DATA_COUNT_ODD scratch ram byte that was used
dynamicaly compute data transfer oddness. This is obviated
by SCB_XFERLEN_ODD field.
aic7xxx.seq:
Be more careful in our handling of the SCB_LUN field. It
must be masked with LID if only lun information is desired.
Remove all updates to the DATA_COUNT_ODD scratch ram field.
Remove all uses of ODD_SEG. These two save quite a few
sequencer instructions.
Use SCB_XFERLEN_ODD to validate the end of transfer
ignore wide residue message case.
aic7xxx_inline.h:
In ahc_queue_scb(), setup the SCB_XFERLEN_ODD field.
Approved by: RE
FAILDIS in the SEQCTL register, not the HCNTRL register.
aic7xxx.c:
Remeber SEQCTL settings in the "seqctl" field of our
softc. seqctl defaults to just having FASTMODE set,
but the bus attachments can override this.
aic7xxx.h:
Add the seqctl softc field.
aic7xxx_pci.c:
Update the seqctl softc field and manually update SEQCTL
when to many PCI errors occur
Approved by: RE
to be more efficient by having the sequencer copy the
single byte of valid lun data into the long lun field.
aic79xx.c:
Memset our hardware SCB to 0 so that untouched
fields don't confuse diagnostic output. With the
old method for handling the Rev A bug, if the long
lun field was not 0, this could result in bogus
lun information being sent to drives.
Use the same SCB transfer size for all chip types
now that the long lun is not DMA'ed to the chip.
aic79xx.seq:
Add code to copy lun information for Rev.A hardware.
aic79xx_inline.h:
Remove host update of the long_lun field on every
packetized command.
Sort IDs based on chip type.
Remove IROC IDs. We'll switch to using the IROC masks
if/when we want to start attaching to IROC controllers.
Approved by: RE
structure, which is new to the 82550 and 82551, is used to transmit
a packet. This appears to fix the packet truncation problem that was
observed when using 82550-based fxp cards to transmit ICMP or fragmented
UDP packets of certain lengths which only had one to three bytes in the
second and final mbuf of the packet. This matches a note in the "Intel
8255x 10/100 Mbps Ethernet Controller Family Open Source Software Developer
Manual", which says that the hardware parse bit should be set when sending
these types of packets.
There have also been unconfirmed reports of similar problems when
transmitting TCP packets, which should not be affected by the above
mentioned change because the hardware parse bit was already being set
if the stack requested hardware checksumming of the packet. If the
problem remains, the use of the IPCB structure can be disabled to
cause the driver to fall back to using the older 82559 interface with
82550-based cards by setting
hint.fxp.UNIT_NUMBER.ipcbxmit_disable
to a non-zero value at boot time, or using kenv to set this variable
before using kldload to load the fxp driver.
Approved by: re (jhb)
set on realtek cards, but they work without it (and don't work with
it). The standard seems to imply that this is just a hint anyway, so
this should be harmless. It doesn't appear to be set on any other
cardbus cards that I have (or have seen).
This should make the rl based CardBus cards work again. I've been
running it for about a month now.
Approved by: re@ (jhb)
buffer space instead of a u_int32_t. Otherwise the upper 32 bits of
the address space get truncated and syscons blows up.
Approved by: re (safe, low risk amd64 fixes)
of the struct plex, which tore apart the mutex linked lists when the
plex table was expanded. Now we maintain a pool of mutexes (currently
32) to be shared by all plexes. This is still a lot better than the
splhigh() method used in other architectures.
expand_table: Add parameters file and line if we're debugging.
Approved by: re (jhb)
of the struct plex, which tore apart the mutex linked lists when the
plex table was expanded. Now we maintain a pool of mutexes (currently
32) to be shared by all plexes. This is still a lot better than the
splhigh() method used in other architectures.
Add and clarify comments.
Approved by: re (jhb)
of the struct plex, which tore apart the mutex linked lists when the
plex table was expanded. Now we maintain a pool of mutexes (currently
32) to be shared by all plexes. This is still a lot better than the
splhigh() method used in other architectures.
Approved by: re (jhb)
of the struct plex, which tore apart the mutex linked lists when the
plex table was expanded. Now we maintain a pool of mutexes (currently
32) to be shared by all plexes. This is still a lot better than the
splhigh() method used in other architectures.
update_volume_config: Remove redundant diskconfig parameter.
expand_table: Add parameters file and line if we're debugging.
Approved by: re (jhb)
Submitted by: Ted Unangst <tedu@stanford.edu>
Correct some inaccurate and badly formatted comments.
config_subdisk: If our drive is down, ensure that the subdisk is
crashed. Previously it was possible for the subdisk
to be up when the drive was down.
Change the way the plex lock mutexes work. Previously they were part
of the struct plex, which tore apart the mutex linked lists when the
plex table was expanded. Now we maintain a pool of mutexes (currently
32) to be shared by all plexes. This is still a lot better than the
splhigh() method used in other architectures.
update_volume_config: Remove redundant diskconfig parameter.
Approved by: re (jhb)
Change config format slightly to save plex preferences correctly.
vinum_scandisk: reinitialise volatile pointer after function call.
This is the "deafc0de" bug.
Approved by: re (scottl)
This fixes net/pppoa port for Alcatel Speedtouch devices.
Submitted by: Jay Cornwall <jay@evilrealms.net>
Tested by: Francois Rogler <francois@rogler.org>
Approved by: re (scottl)
on if_fxp cards. When flow control is enabled, if the operating system
doesn't acknowledge the packet buffer filling, the card will begin to
generate ethernet quench packets, but appears to get into a feedback
loop of some sort, hosing local switches. This is a temporary workaround
for 5.1: the ability to configure flow control should probably be
exposed by some or another management interface on ethernet link layer
devices.
Approved by: re (bmah)
Reviewed by: mux
all of the Optio series have the same problems. It might be a better
approach eventually to add wildcard support to USB quirks.
PR: kern/50271, kern/46369
Approved by: re (rwatson)
- Fix compilation without GEM_DEBUG.
- Do not #define GEM_DEBUG by default; it adds overhead (due to bzero()ing
RX space) and is not needed any more, since the driver is quite stable
now.
- Fix watchdog timeouts when failing to load TX packets.
- Do not forcibly limit the number of descriptors used for a packet to
GEM_NTXSEGS, by passing this number to bus_dma_tag_create(). There is
no requirement for a limit any lower than the total number of
available descriptors, and the present limit caused network problems
due to mbuf chains requiring more descriptors.
GEM_NTXSEGS is still used to estimate the interrupt window size, for
which we just need an estimate.
Approved by: re (rwatson)
The submitter of PR 32118 told me that this patch also fixes autoselecting
for znyx 4 port cards (10baseT, 100baseTX did work already).
PR: 32118
Reviewed by: imp
Approved by: rwatson (re)
has already been registered with ATAPI/CAM (else there is nothing
to do). atapi_cam_reinit_bus may be called before the bus is
registered if an ATAPI command times out during the boot sequence.
PR: i386/51421
Reviewed by: roberto
Approved by: re (rwatson)
MFC after: 1 week
by using a __packed keyword for the fxp_rfa structure. The Intel
guys who designed this structure with unaligned fields deserve
to be shot.
Tested by: kris
Approved by: re@ (jhb)
bus_dma MD code for AMD64. (And a trivial ifdef update in dev/kbd because
of this). More updates are needed here to take advantage of the 64 bit
instructions.
Approved by: re (blanket amd64/*)
- Simplify and correct the bus manager election process.
- Check link_active when choosing cycle master.
- Fix location of the cmr bit.
Approved by: re (scottl)
series. This driver was generously developed and released by David
Jeffreys and Adaptec. I've updated it to work with 5.x and fixed a
few bugs.
MFC After: 1 week
ASIC revision is really the major number of the CHIPID. Also store
the chipid, asic rev and chip revision in the softc for later use.
- The write twice to send producer index workaround only applies to
the 5700_BX chips, so only do it there.
Requested by: jdp
- Do not initalize the LED's to 0x00. The default configuration
the chip comes up in should yeild proper operation of the LED's.
Confirmed by: John Cagle <john.cagle@hp.com>
Approved by: re (blanket)
ILMI daemons. Factor out common softc fields for all ATM interfaces that
need to be externally visible into an ifatm structure and make the midway
driver using this structure and fill the MIB.
Maintain sector sizes for all objects, not just for drives. Some of
this could do with improvement: in particular, we get an error if the
components of an object have different sector sizes.
Clean up some comments.
