reduces the size of the pv_entry structure a small but significant amount.
This is implemented a little differently because it isn't so cheap to get
the physical address of the page tabke page on amd64.. instead of it
being directly accessible from the top level page directory, it is now
two additional tree levels down. However.. In almost all cases, we
recently had the physical address if the page table page a short while
before we needed it, but it slipped through our fingers. This patch
saves it for when we do need it. Also, for the one case where we do not
have the ptp paddr, we are always running in curproc context and so we
can do a vtopte-like trick. I've implemented vtopde() for this purpose.
There is still a CYA entry in pmap_unuse_pt() that needs to be removed. I
think it can be removed now but I forgot to test with it gone.
1. Add global varible _libkse_debug, debugger uses the varible to identify
libpthread. when the varible is written to non-zero by debugger, libpthread
will take some special action at context switch time, it will check
TMDF_DOTRUNUSER flags, if a thread has the flags set by debugger, it won't
be scheduled, when a thread leaves KSE critical region, thread checks
the flag, if it was set, the thread relinquish CPU.
2. Add pq_first_debug to select a thread allowd to run by debugger.
3. Some names prefixed with _thr are renamed to _thread prefix.
which is allowed to run by debugger.
sched_add() rather than just doing it in sched_wakeup(). The old
ithread preemption code used to set NEEDRESCHED unconditionally if it
didn't preempt which masked this bug in SCHED_4BSD.
Noticed by: jake
Reported by: kensmith, marcel
Add a MOD_QUIESCE event for modules. This should return error (EBUSY)
of the module is in use.
MOD_UNLOAD should now only fail if it is impossible (as opposed to
inconvenient) to unload the module. Valid reasons are memory references
into the module which cannot be tracked down and eliminated.
When kldunloading, we abandon if MOD_UNLOAD fails, and if -force is
not given, MOD_QUIESCE failing will also prevent the unload.
For backwards compatibility, we treat EOPNOTSUPP from MOD_QUIESCE as
success.
Document that modules should return EOPNOTSUPP for unknown events.
needed so that sysresource objects are created first to reserve all regions,
then other devices can allocate from them. Otherwise, acpi_timer (the only
ACPI device with an identify routine), would allocate its resources from
the nexus, causing the later sysresource reserve to fail.
Debugging by: Taku YAMAMOTO, Andrea Campi
1. Add tm_lwpid into kse_thr_mailbox to indicate which kernel
thread current user thread is running on. Add tm_dflags into
kse_thr_mailbox, the flags is written by debugger, it tells
UTS and kernel what should be done when the process is being
debugged, current, there two flags TMDF_SSTEP and TMDF_DONOTRUNUSER.
TMDF_SSTEP is used to tell kernel to turn on single stepping,
or turn off if it is not set.
TMDF_DONOTRUNUSER is used to tell kernel to schedule upcall
whenever possible, to UTS, it means do not run the user thread
until debugger clears it, this behaviour is necessary because
gdb wants to resume only one thread when the thread's pc is
at a breakpoint, and thread needs to go forward, in order to
avoid other threads sneak pass the breakpoints, it needs to remove
breakpoint, only wants one thread to go. Also, add km_lwp to
kse_mailbox, the lwp id is copied to kse_thr_mailbox at context
switch time when process is not being debugged, so when process
is attached, debugger can map kernel thread to user thread.
2. Add p_xthread to proc strcuture and td_xsig to thread structure.
p_xthread is used by a thread when it wants to report event
to debugger, every thread can set the pointer, especially, when
it is used in ptracestop, it is the last thread reporting event
will win the race. Every thread has a td_xsig to exchange signal
with debugger, thread uses TDF_XSIG flag to indicate it is reporting
signal to debugger, if the flag is not cleared, thread will keep
retrying until it is cleared by debugger, p_xthread may be
used by debugger to indicate CURRENT thread. The p_xstat is still
in proc structure to keep wait() to work, in future, we may
just use td_xsig.
3. Add TDF_DBSUSPEND flag, the flag is used by debugger to suspend
a thread. When process stops, debugger can set the flag for
thread, thread will check the flag in thread_suspend_check,
enters a loop, unless it is cleared by debugger, process is
detached or process is existing. The flag is also checked in
ptracestop, so debugger can temporarily suspend a thread even
if the thread wants to exchange signal.
4. Current, in ptrace, we always resume all threads, but if a thread
has already a TDF_DBSUSPEND flag set by debugger, it won't run.
Encouraged by: marcel, julian, deischen
