error address on a decoding error to unlatch it and to allow
us to print a better diagnostics message. This also has the
side effect of clearing the condition, which prevents an
interrupt storm.
Revert back to the previous method of doing it for where a node can be
identified and it's an 11n node.
I'll have to do some further research into exactly what is being messed up
with the sequence number matching and I'll then revisit this.
This doesn't yet take into account HT40 packet durations as the node info
(needed to know if it's a HT20 or HT40 node) isn't available everywhere
it needs to be.
free i-nodes or blocks to handle a race where another thread might have
allocated the last i-node or block while we were waiting for the buffer.
Tested by: dougb
putting descriptors (not buffers) across a 4k page boundary can cause issues.
I've not seen it in production myself but it apparently can cause problems.
So, in preparation for addressing this workaround, (re)-expose the particular
HAL capability bit which marks whether the chipset has support for cross-4k-
boundary transactions or not.
A subsequent commit will modify the descriptor allocation to avoid allocating
descriptor entries that straddle a 4k page boundary.
disk. When multiple devices are specified, a non-supporting ioctl will
cause diskinfo(8) to stop at the point which does not seem to be necessary.
Ok'ed by: phk
MFC after: 1 month
a hard hang due to an interrupt storm or stuck interrupt pin. We
return the next IRQ that is larger than the last one returned and
in doing so give all interrupts a fair chance of being handled.
Consequently, we're able to break into the kernel debugger in such
an event.
masked-off by the firmware.
o In DELAY(). Make sure we have an inner-loop body that the compiler
cannot eliminate. While timing does not have to be perfect, the
loops must be there to have at least some notion of delay.
Obtained from: Juniper Networks
misnamed since it was introduced and should not be globally exposed
with this name. The equivalent functionality is now available using
kern_yield(curthread->td_user_pri). The function remains
undocumented.
Bump __FreeBSD_version.
- entirely eliminate some calls to uio_yeild() as being unnecessary,
such as in a sysctl handler.
- move should_yield() and maybe_yield() to kern_synch.c and move the
prototypes from sys/uio.h to sys/proc.h
- add a slightly more generic kern_yield() that can replace the
functionality of uio_yield().
- replace source uses of uio_yield() with the functional equivalent,
or in some cases do not change the thread priority when switching.
- fix a logic inversion bug in vlrureclaim(), pointed out by bde@.
- instead of using the per-cpu last switched ticks, use a per thread
variable for should_yield(). With PREEMPTION, the only reasonable
use of this is to determine if a lock has been held a long time and
relinquish it. Without PREEMPTION, this is essentially the same as
the per-cpu variable.
* The existing radio config code was for the AR5416/AR9160 and missed out
on some of the AR9280 specific stuff. Include said stuff from ath9k.
* Refactor out the gain control settings into a new function, again pilfered
from ath9k.
* Use the analog register RMW macro when touching analog registers.
Obtained from: Linux ath9k
calling thread's unique integral ID, which is similar to AIX function of
the same name. Bump __FreeBSD_version to note its introduction.
Reviewed by: kib
BUFSIZ. Use LINE_MAX * 2 as the buffer size (BSIZE).
- Error out if we encounter a line longer than LINE_MAX. The previous
behavior was to silently split long lines and produce corrupted
output.
PR: bin/151384
* Store the flowid when receiving an SCTP/IPv6 packet.
* Store the flowid when receiving an SCTP packet with wrong CRC.
* Initilize flowid correctly.
* Put test code under INVARIANTS.
MFC after: 3 months.
Clear the padding when returning context to the usermode, for
MI ucontext_t and x86 MD parts.
Kernel allocates the structures on the stack, and not clearing
reserved fields and paddings causes leakage.
pins to determine whether there's a high register set or not. This
allows platform_gpio_init() to work without duplicating the work
done in the attach method.
All 9.6 users with DNSSEC validation enabled should upgrade to this
version, or the latest version in the 9.7 branch, prior to 2011-03-31
in order to avoid validation failures for names in .COM as described
here:
https://www.isc.org/announcement/bind-9-dnssec-validation-fails-new-ds-record
In addition the fixes for this and other bugs, there are also the
following:
* Various fixes to kerberos support, including GSS-TSIG
* Various fixes to avoid leaking memory, and to problems that could
prevent a clean shutdown of named
o) Have mips_wblush just do syncw, not sync on Cavium Octeon.
o) Add support for reading and writing some Octeon-specific registers.
NB: Some of these are not entirely Octeon-specific.
Submitted by: Bhanu Prakash
This fixes two problems -
* All packets need to be processed here, not just aggregate ones - as any
received frames (AMPDU or otherwise) in the given TID (traffic class id)
will update the sequence number and, implied with that, update the window;
* It seems there's situations where packets aren't matching a current node but
somehow need to be tracked. Thus just tag them all for now; I'll figure out
the why later.
Whilst I'm here, bump the stats counters whilst I'm at it.
This fixes AMPDU RX in my tests; the main problems now stem from what look
like PHY level error/retransmits which are impeding general throughput, incl.
AMPDU.
