memory disk is larger than the number of available sf_bufs, this improves
performance on SMPs by eliminating interprocessor TLB shootdowns. For
example, with 6656 sf_bufs, the default on my test machine, and a 256MB
swap-backed memory disk, I see the command
"dd if=/dev/md0 of=/dev/null bs=64k" achieve ~489MB/sec with the default,
shared mappings, and ~587MB/sec with CPU private mappings.
base transfer speed to CAM. The actual value used (40MB/s) is fairly
arbitrary, but assumes the same 33% overhead as was implied by the
1MB/s figure we used for USB1 devices.
are not added to the list(s) of available settings. However, other drivers
can call the CPUFREQ_DRV_SETTINGS() method on those devices directly to
get info about available settings.
Update the acpi_perf(4) driver to use this flag in the presence of
"functional fixed hardware." Thus, future drivers like Powernow can
query acpi_perf for platform info but perform frequency transitions
themselves.
throttling, neglecting to do this kept the sysctls from appearing.
Attach an acpi_throttle device to each CPU that supports it.
Don't add a device if the P_BLK is invalid or if _PTC is not present.
This removes extraneous probe/attach failure messages on some machines.
Make the cpu throttle state local to the softc to account for partial
successes when changing the clock rate on MP machines.
for nodes hanging off of Central (untested), FireHose (untested) and
PCI (tested) busses.
- Add an additional parameter to OF_decode_addr() which specifies the
index of the register bank to decode.
These should allow to eventually add support for the Z8530 hanging off of
FireHose to uart(4) and to write support for PCI-based graphics adapters.
Suggested by: tmm (back in '03)
o Add a fallback location for the MAC address. Most of the early ne2000
PC Cards were built from the same parts, so most of them have the same
address in the CIS to grab the MAC from. Use this address as our
fallback if we don't find anything better.
o Add printf, in bootverbose, noting the MAC addresses that we find along
the way.
# Better sanity checking of the MAC address is needed. Will have to
# investigate using/creating a centralized function to do this as a number
# of other PC Card drivers each have their own ad-hoc tests.
1. Dependency on netgraph module was broken (wrong version).
2. Netgraph node type was never destroyed on unload. This
was masked by problem #1.
Fixed both by using NETGRAPH_INIT(). Now netgraph node type
is created on module load, as in the rest of netgraph modules.
at some offset. Unlike newer cards, the MAC address wasn't part of
the CIS as a specific FUNCE. These older cards were having their MAC
address show up as 0:2:4:6:8:a because that's what's in the ROM
locations that would be there in a real ne2000.
This patch allows one to specify the offset for the MAC address for
these cards. Specify one for the IBM Ethernet II card, as it is one
that has this problem. One shouldn't specify this unless the MAC
address really isn't in the CIS at all.
Side note: The novell probe likely shouldn't read the MAC address, and
that should be moved to the bus specific attach routine(s), maybe as a
convenience function in if_ed_novell.c.
My IBM Ethernet II (aka Info Mover) now has a believable MAC address.
are NOVELL NE2000 with just a tiny quirk that's non vendor specific.
Instead, use the chip_type of DL100XX instead. This is more inline
with how the AX88190 support was added, and seems a little cleaner.
pessmize the error recover path through edintr by calling these
functions, rather than expanding it inline. This error path already
does a lot in it, so an extra function call will be lost in the noise.
It also happens rarely.
while (complicated-expr)
continune;
in preference to
while (complicated-expr);
since the code generated is identical, and the former is easier to read,
especially for complicated-expr that reach to the end of the line...
Older cards have it reversed.
Also, use some already defined values instead of magic numbers.
PR: 73324
Submitted by: arne_woerner@yahoo.com
MFC after: 1 week
fix the problem with device discovery seen by some people.
2. Change to make 3ware CLI/3DM work on amd64.
3. Fix a potential problem that could cause the driver to do strlen(NULL) when
using older firmware.
Reviewed by:scottl
probing the novell ne[12]000 cards. It should be its own thing, ala
how we do the dl100xx support doing its own thing at the right time.
For the moment, it is just a function, which makes the mainline of the
generic probe easier to follow.
Also, correct a couple of comments that looked wrong.
# there may be a bug in setting up gwether, in that we set
# sc->rec_page_stop based on memsize, rather than sc->mem_size, so if
# these two are different, then the rec_page_stop will be wrong. I'm
# hesitant to fix it without real hardware to test with. Since
# gwether isn't in the hardware list of the man page nor in the commit
# messages, it is hard to know for sure.
and wd80x3 support. Make the obscure ISA cards optional, and add
those options to NOTES on i386 (note: the ifdef around the whole code
is for module building). Tweak pc98 ed support to include wd80x3 too.
Add goo for alpha too.
The affected cards are the 3Com 3C503, HP LAN+ and SIC (whatever that
is). I couldn't find any of these for sale on ebay, so they are
untested. If you have one of these cards, and send it to me, I'll
ensure that you have no future problems with it...
Minor cleanups as well by using functions rather than cut and paste
code for some probing operations (where the function call overhead is
lost in the noise).
Remove use of kvtop, since they aren't required anymore. This driver
needs to get its memory mapped act together, however, and use bus
space. It doesn't right now.
This reduces the size of if_ed.ko from about 51k to 33k on my laptop.
same as the LINKSYS COMBO_ECARD (which also seems to be the same as
another linksys product that also has a modem, but I can't find that
one at the moment). Remove the PCM100, since it is now no longer
used.
o The COMBO_ECARD comes in many flavors, it seems, so probe both the DL10019
and the AX88x90 on it. Since this seems to work with no ill effects, maybe
the probing should happen more generally rather than being table driven.
Need to think more about this.
o Remove PCM100 because it is duplicative (the ETHERFAST is the pcm100 and
apparently has the same IDs). It was here for NetBSD because they match
up an expected MAC address OID, but since we don't bother with that, we
don't need to be so finely discriminating.
o Minor style nit.
if_ed_isa.c, and they seem to not be helpful anymore.
o Fix style issues from de-Pification.
o change from _isa_ to _cbus_ to the largest extent possible to reflect that
this is really for cbus, not isa.
o Use ANSI function definitions.
o Use ed_clear_memory
o eliminate kvtop
