- add "sse3" to MACHINE_CPU for the new cpu types
- for i386, default to CPUTYPE=prescott for the new cpu types
PR: gnu/154906
Discussed with: kib, kan, dim
MFC after: 2 weeks
and k8-sse3 cpu-types for -march=/-mtune= gcc options.
These new cpu-types include the SSE3 instruction set that is supported
by all newer AMD Athlon 64 and Opteron processors.
All three cpu-types are supported by clang and all gcc versions
starting with 4.3 SVN rev 124339 (at that time GPLv2 licensed).
PR: gnu/154906
Discussed with: kib, kan, dim
Obtained from: gcc 4.3 (r124339, GPLv2 licensed)
MFC after: 2 weeks
vfs_export() fails. Restoring old options and flags after successful
VFS_MOUNT(9) call may cause the file system internal state to become
inconsistent with mount options and flags. Specifically the FFS super
block fs_ronly field and the MNT_RDONLY flag may get out of sync.
PR: kern/133614
Discussed on: freebsd-hackers
Most of the ports I broke when I imported utmpx, were simple management
utilities for the utmp database, allowing you to add/remove entries
manually.
Add a small tool called utxrm(8), which allows you to remove an entry
from the utmpx database by hand. This is useful when a login daemon
crashes or fails to remove the entry during shutdown.
- Add screen-256color,
- Improve rxvt-256color to set pa and op properly.
- Add rxvt-unicode-256color as an alias to rxvt-256color.
PR: conf/152713, conf/153164
Submitted by: Alexander Verbod and Frédéric Perrin
MFC after: 2 weeks
'All' and 'Minimal'. Update the keys for Minimal and Custom to avoid the
conflict.
PR: bin/153809
Submitted by: Janne Snabb <snabb at epipe.com>
MFC after: 3 days
respectively and fix all bus_dma(9) issues seen when bounce buffers
are used.
o Setup frame handling had no bus_dmamap_sync(9) which prevented
driver from configuring RX filter. Add missing bus_dmamap_sync(9)
in both dc_setfilt_21143()/dc_setfilt_xircom() and dc_txeof().
o Use bus_addr_t for DMA segment instead of using u_int32_t.
o Introduce dc_dma_alloc()/dc_dma_free() functions to allocate/free
DMA'able memory.
o Create two DMA descriptor list for each TX/RX lists. This change
will minimize the size of bounce buffers that would be used in
each TX/RX path. Previously driver had to copy both TX/RX lists
when bounce buffer is active.
o 21143 data sheet says descriptor list requires 4 bytes alignment.
Remove PAGE_SIZE alignment restriction and use
sizeof(struct dc_dec).
o Setup frame requires 4 bytes alignment. Remove PAGE_SIZE
alignment restriction and use sizeof(struct dc_dec).
o Add missing DMA map unload for both setup frame and TX/RX
descriptor list.
o Overhaul RX handling logic such that make driver always allocate
new RX buffer with dc_newbuf(). Previously driver allowed to
copy received frame with m_devget(9) after passing the
descriptor ownership to controller. This can lead to passing
wrong frame to upper stack.
o Introduce dc_discard_rxbuf() which will discard received frame
and reuse loaded DMA map and RX mbuf.
o Correct several wrong bus_dmamap_sync(9) usage in dc_rxeof and
dc_txeof. The TX/RX descriptor lists are updated by both driver
and HW so READ/WRITE semantics should be used.
o If driver failed to allocate new RX buffer, update if_iqdrops
counter instead of if_ierrors since driver received the frame
without errors.
o Make sure to unload loaded setup frame DMA map in dc_txeof and
clear the mark of setup frame of the TX descriptor in dc_txeof().
o Add check for possible TX descriptor overruns in dc_encap() and
move check for free buffer to caller, dc_start_locked().
o Swap the loaded DMA map and the last DMA map for multi-segmented
frames. Since dc_txeof() assumes the last descriptor of the
frame has the DMA map, driver should swap the first and the last
DMA map in dc_encap(). Previously driver tried to unload
not-yet-loaded DMA map such that the loaded DMA map was not
unloaded at all for multi-segmented frames.
o Rewrite DC_RXDESC/DC_TXDESC macro to simpler one.
o Remove definition of ETHER_ALIGN, it's already defined in
ethernet.h.
With this changes, dc(4) works with bounce buffers and it shall
also fix issues which might have shown in PAE environments.
Tested by: marius
Previously dc(4) always checked whether there is pending interrupts
and this consumed a lot of CPU cycles in interrupt handler. Limit
the number of processing for TX/RX frames to 16. Also allow sending
frames in the loop not to starve TX under high RX load.
Reading DC_ISR register should be protected with driver lock,
otherwise interrupt handler could be run(e.g. link state change)
before the completion of dc_init_locked().
While I'm here remove unneeded code.
as well as controller has enough free TX descriptors.
Remove check for number of queued frames before attempting to
transmit. I guess it was added to allow draining queued frames
even if there is no link. I'm under the impression this type of
check should be done in upper layer. No other drivers in tree do
that.
ownership to controller before completion of access to the
descriptor. Driver is faking up status word so it should not give
ownership to controller until it completes RX processing.
the debugger back-end has changed. This means that switching from ddb
to gdb no longer requires a "step" which can be dangerous on an
already-crashed kernel.
Also add a capability to get from the gdb back-end back to ddb, by
typing ^C in the console window.
While here, simplify kdb_sysctl_available() by using
sbuf_new_for_sysctl(), and use strlcpy() instead of strncpy() since the
strlcpy semantic is desired.
MFC after: 1 month
x86 CPU support, better support for powerpc64, some new directives, and
many other things. Bump __FreeBSD_version, and add a note to UPDATING.
Thanks to the many people that have helped to test this.
Obtained from: projects/binutils-2.17
request TX completion interrupt for every 8-th frames. Previously
dc(4) requested TX completion interrupt if number of queued TX
descriptors is greater than 64. This caused a lot of TX completion
interrupt under high TX load once driver queued more than 64 TX
descriptors. It's quite normal to see more than 64 queued TX
descriptors under high TX load.
This change reduces the number of TX completion interrupts to be
less than 17k under high TX load. Because this change does not
generate TX completion interrupt for each frame, add reclaiming
transmitted buffers in dc_tick not to generate false watchdog
timeouts.
While I'm here add check for queued descriptors in dc_txeof() since
there is no more work to do when there is no pending descriptors.
