1) Include opt_platform.h to get QORIQ_DPAA. Otherwise the definition of
OCP85XX_TGTIF_LBC is incorrect.
2) The child resources are already allocated, just activate them, instead of
incorrectly remapping the memory regions (resource lists for lbc consist of the
virtual address of the child's resources, not the physical address).
Sponsored by: Alex Perez/Inertial Computing
Some MPC85xx GPIO controllers are compatible with QorIQ.
It may make more sense in the future to rename this and mpc85xx_gpio.c, as
mpc85xx_gpio.c appears to only be compatible with a few mpc85xx SoCs. All other
MPC85xx SoCs use the same controller as QorIQ.
Freescale's QorIQ line includes a new ethernet controller, based on their
Datapath Acceleration Architecture (DPAA). This uses a combination of a Frame
manager, Buffer manager, and Queue manager to improve performance across all
interfaces by being able to pass data directly between hardware acceleration
interfaces.
As part of this import, Freescale's Netcomm Software (ncsw) driver is imported.
This was an attempt by Freescale to create an OS-agnostic sub-driver for
managing the hardware, using shims to interface to the OS-specific APIs. This
work was abandoned, and Freescale's primary work is in the Linux driver (dual
BSD/GPL license). Hence, this was imported directly to sys/contrib, rather than
going through the vendor area. Going forward, FreeBSD-specific changes may be
made to the ncsw code, diverging from the upstream in potentially incompatible
ways. An alternative could be to import the Linux driver itself, using the
linuxKPI layer, as that would maintain parity with the vendor-maintained driver.
However, the Linux driver has not been evaluated for reliability yet, and may
have issues with the import, whereas the ncsw-based driver in this commit was
completed by Semihalf 4 years ago, and is very stable.
Other SoC modules based on DPAA, which could be added in the future:
* Security and Encryption engine (SEC4.x, SEC5.x)
* RAID engine
Additional work to be done:
* Implement polling mode
* Test vlan support
* Add support for the Pattern Matching Engine, which can do regular expression
matching on packets.
This driver has been tested on the P5020 QorIQ SoC. Others listed in the
dtsec(4) manual page are expected to work as the same DPAA engine is included in
all.
Obtained from: Semihalf
Relnotes: Yes
Sponsored by: Alex Perez/Inertial Computing
Summary:
Some drivers need special memory requirements. X86 solves this with a
pmap_change_attr() API, which DRM uses for changing the mapping of the GART and
other memory regions. Implement the same function for PowerPC. AIM currently
does not need this, but will in the future for DRM, so a default is added for
that, for business as usual. Book-E has some drivers coming down that do
require non-default memory coherency. In this case, the Datapath Acceleration
Architecture (DPAA) based ethernet controller has 2 regions for the buffer
portals: cache-inhibited, and cache-enabled. By default, device memory is
cache-inhibited. If the cache-enabled memory regions are mapped
cache-inhibited, an alignment exception is thrown on access.
Test Plan:
Tested with a new driver to be added after this (DPAA dTSEC ethernet driver).
No alignment exceptions thrown, driver works as expected with this.
Reviewed By: nwhitehorn
Sponsored by: Alex Perez/Inertial Computing
Differential Revision: https://reviews.freebsd.org/D5471
Extract common code from PowerPC's ofw_pci
Import portions of the PowerPC OF PCI implementation into
new file "ofw_pci.c", common for other platforms. The files ofw_pci.c and
ofw_pci.h from sys/powerpc/ofw no longer exist. All required declarations
are moved to sys/dev/ofw/ofw_pci.h.
This creates a new ofw_pci_write_ivar() function and modifies
ofw_pci_nranges(), ofw_pci_read_ivar(), ofw_pci_route_interrupt()
methods.
Most functions contain existing ppc implementations in the majority
unchanged. Now there is no need to have multiple identical copies
of methods for various architectures.
Submitted by: Marcin Mazurek <mma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Annapurna Labs
Reviewed by: jhibbits, mmel
Differential Revision: https://reviews.freebsd.org/D4879
This needs to return to the drawing board as it breaks both
PowerPC and Sparc64 build.
Pointed out by: jhibbits
This simplifies checking for default resource range for bus_alloc_resource(),
and improves readability.
This is part of, and related to, the migration of rman_res_t from u_long to
uintmax_t.
Discussed with: jhb
Suggested by: marcel
Import portions of the PowerPC OF PCI implementation into
new file "ofw_pci.c", common for other platforms. The files ofw_pci.c and
ofw_pci.h from sys/powerpc/ofw no longer exist. All required declarations
are moved to sys/dev/ofw/ofw_pci.h.
This creates a new ofw_pci_write_ivar() function and modifies
ofw_pci_nranges(), ofw_pci_read_ivar(), ofw_pci_route_interrupt() methods.
Most functions contain existing ppc implementations in the majority
unchanged. Now there is no need to have multiple identical copies
of methods for various architectures.
Submitted by: Marcin Mazurek <mma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Annapurna Labs
Reviewed by: jhibbits, mmel
Differential Revision: https://reviews.freebsd.org/D4879
Provide bus_get_bus_tag() for sparc64, powerpc, arm, arm64 and mips
nexus and its children in order to return a platform specific default tag.
This is required to ensure generic correctness of the bus_space tag.
It is especially needed for arches where child bus tag does not match
the parent bus tag. This solves the problem with ppc architecture
where the PCI bus tag differs from parent bus tag which is big-endian.
This commit is a part of the following patch:
https://reviews.freebsd.org/D4879
Submitted by: Marcin Mazurek <mma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Annapurna Labs
Reviewed by: jhibbits, mmel
Differential Revision: https://reviews.freebsd.org/D4879
will allow for code that uses the old fdt_get_range and fdt_regsize
functions to find a range, map it, access, then unmap to replace this, up
to and including the map, with a call to OF_decode_addr.
As this function should only be used in the early boot code the unmap is
mostly do document we no longer need the mapping as it's a no-op, at least
on arm.
Reviewed by: jhibbits
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D5258
ucontext_t available. Our code even has XXX comment about this.
Add a bit of compliance by moving struct __ucontext definition into
sys/_ucontext.h and including it into signal.h and sys/ucontext.h.
Several machine/ucontext.h headers were changed to use namespace-safe
types (like uint64_t->__uint64_t) to not depend on sys/types.h.
struct __stack_t from sys/signal.h is made always visible in private
namespace to satisfy sys/_ucontext.h requirements.
Apparently mips _types.h pollutes global namespace with f_register_t
type definition. This commit does not try to fix the issue.
PR: 207079
Reported and tested by: Ting-Wei Lan <lantw44@gmail.com>
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Summary:
The revised Book-E spec, adding the specification for the MMUv2 and e6500,
includes a hardware PTE layout for indirect page tables. In order to support
this in the future, migrate the PTE format to match the MMUv2 hardware PTE
format.
Test Plan: Boot tested on a P5020 board. Booted to multiuser mode.
Differential Revision: https://reviews.freebsd.org/D5224
ABI of struct fpreg. The FPU emulator operates on the "raw" FPU state
stored in the pcb rather than the "cooked" fpreg state used for ptrace()
and cores.
Reported by: bz
The stack must be aligned to 16 bytes at all times. Clang 3.8 is especially
adamant about this, and causes strange behavior and segmentation faults if it is
not the case.
PR: kern/206810
Device trees mark lbc as compatible with simplebus. Since simplebus is passed
first, it attaches first. When lbc's pass (default pass) comes, the bus is
already attached to simplebus, so is skipped.
Sponsored by: Alex Perez/Inertial Computing
The PT_{GET,SET}FPREGS requests use 'struct fpreg' and the NT_FPREGSET
core note stores a copy of 'struct fpreg'. As with x86 and the floating
point state there compared to the extended state in XSAVE, struct fpreg
on powerpc now only holds the 'base' FP state, and setting it via
PT_SETFPREGS leaves the extended vector state in a thread unchanged.
Reviewed by: jhibbits
Differential Revision: https://reviews.freebsd.org/D5004
Use driver settable callbacks for handling of:
- core post reset
- reading actual port speed
Typically, OTG enabled EHCI cores wants setting of USBMODE register,
but this register is not defined in EHCI specification and different
cores can have it on different offset.
Also, for cores with TT extension, actual port speed must be determinable.
But again, EHCI specification not covers this so this patch provides
function for two most common variant of speed bits layout.
Reviewed by: hselasky
Differential Revision: https://reviews.freebsd.org/D5088
POSIX requires these members to be of type void * rather than the
char * inherited from 4BSD. NetBSD and OpenBSD both changed their
fields to void * back in 1998. No new build failures were reported
via an exp-run.
PR: 206503 (exp-run)
Reviewed by: kib
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D5092
Summary:
Migrate to using the semi-opaque type rman_res_t to specify rman resources. For
now, this is still compatible with u_long.
This is step one in migrating rman to use uintmax_t for resources instead of
u_long.
Going forward, this could feasibly be used to specify architecture-specific
definitions of resource ranges, rather than baking a specific integer type into
the API.
This change has been broken out to facilitate MFC'ing drivers back to 10 without
breaking ABI.
Reviewed By: jhb
Sponsored by: Alex Perez/Inertial Computing
Differential Revision: https://reviews.freebsd.org/D5075
The only difference between dcbzl and dcbz is dcbzl operates on native cache
line lengths regardless of L1CSR0[DCBZ32]. Since we don't change the cache line
size, the cacheline_size variable will reflect the used cache line length, and
dcbz will work as expected.
By confining the page table management to a handful of functions it'll be
easier to modify the page table scheme without affecting other functions.
This will be necessary when 64-bit support is added, and page tables become
much larger.
VM_MAX_KERNEL_ADDERESS is the maximum KVA address. 0xf8000000 is the start of
device mapping space. Since several conditional checks use '<=' against
VM_MAX_KERNEL_ADDRESS, bad things could feasibly happen.
On powerpc64, pointers are 64 bits, so casting from uint32_t changes the integer
width.
The alternative was to use register_t, but I didn't see register_t used as
argument type for any other functions, though didn't look too closely. u_long
was an acceptable alternative. On 64-bit it's 64 bits, on 32-bit it's 32 bits.
powerpc_init() initializes the mmu. Since this may clear pages via
pmap_zero_page(), set the cacheline size before calling into it, so
pmap_zero_page() has the right cacheline size. This isn't completely
necessary now, but will be when 64-bit book-e is completed.
For rs6000, most memory insns and addi/addis do not allow GPR0 for RA
(they use literal zero there instead). So use a 'b' constraint to make
sure to have a base register other than GPR0.
GCC-4.7 and up handles this with allocating r9 instead of r0.
providing compiled-in static environment data that is used instead of any
data passed in from a boot loader.
Previously 'env' worked only on i386 and arm xscale systems, because it
required the MD startup code to examine the global envmode variable and
decide whether to use static_env or an environment obtained from the boot
loader, and set the global kern_envp accordingly. Most startup code wasn't
doing so. Making things even more complex, some mips startup code uses an
alternate scheme that involves calling init_static_kenv() to pass an empty
buffer and its size, then uses a series of kern_setenv() calls to populate
that buffer.
Now all MD startup code calls init_static_kenv(), and that routine provides
a single point where envmode is checked and the decision is made whether to
use the compiled-in static_kenv or the values provided by the MD code.
The routine also continues to serve its original purpose for mips; if a
non-zero buffer size is passed the routine installs the empty buffer ready
to accept kern_setenv() values. Now if the size is zero, the provided buffer
full of existing env data is installed. A NULL pointer can be passed if the
boot loader provides no env data; this allows the static env to be installed
if envmode is set to do so.
Most of the work here is a near-mechanical change to call the init function
instead of directly setting kern_envp. A notable exception is in xen/pv.c;
that code was originally installing a buffer full of preformatted env data
along with its non-zero size (like mips code does), which would have allowed
kern_setenv() calls to wipe out the preformatted data. Now it passes a zero
for the size so that the buffer of data it installs is treated as
non-writeable.
LBC block size can only be up to 4GB. The existing code already clamps it, but
mixes unsigned long and uint32_t. This works on 32-bit targets, but not 64-bit,
so isn't completely correct. This fixes the type confusion.
Newer Book-E cores (e500mc, e5500, e6500) do not support the WE bit in the MSR,
and instead delegate CPU idling to the SoC.
Perhaps in the future the QORIQ_DPAA option for the mpc85xx platform will become
a subclass, which will eliminate most of the #ifdef's.
This includes the following changes:
* SMP kickoff for QorIQ (tested on P5020)
* Errata fixes for some silicon revisions
* Enables L2 (and L3 if available) caches
Obtained from: Semihalf
Sponsored by: Alex Perez/Inertial Computing
