Instead of providing a wrapper around device_delete_child() that the PCI
bus and child bus drivers must call explicitly, move the bulk of the logic
from pci_delete_child() into a bus_child_deleted() method
(pci_child_deleted()). This allows PCI devices to be safely deleted via
device_delete_child().
- Add a bus_child_deleted method to the ACPI PCI bus which clears the
device_t associated with the corresponding ACPI handle in addition to
the normal PCI bus cleanup.
- Change cardbus_detach_card to call device_delete_children() and move
CardBus-specific delete logic into a new cardbus_child_deleted() method.
- Use device_delete_child() instead of pci_delete_child() in the SRIOV code.
- Add a bus_child_deleted method to the OpenFirmware PCI bus drivers which
frees the OpenFirmware device info for each PCI device.
Reviewed by: imp
Tested on: amd64 (CardBus and PCI-e hotplug)
Differential Revision: https://reviews.freebsd.org/D5831
The urtwn hardware transmits FF/A-MSDU just fine - it takes an 802.11
frame and will dutifully send the thing.
So:
* bump RX queue up from 1. Why's it 1? That's really silly.
* Add the "software A-MSDU" encap capability bit.
* bump the TX buffer size up so we can at least send A-MSDU frames.
* track active frames submitted to the NIC - we can't make assumptions
about how many are in flight in the NIC though. For 88E parts we
could use per-packet TX indication, but for R92 parts we can't.
So, just fake it somewhat.
* Kick the transmit queue when we finish reception; try to avoid stalls.
* Kick the FF queue a little more regularly.
A-MSDU TX won't happen until the net80211 side is done, but atheros
fast-frames support should now work.
Tested:
* urtwn0: MAC/BB RTL8188EU, RF 6052 1T1R ; A-MSDU transmit.
This is compatible with the ds1307, but comparing the mcp7941x datasheet vs the
ds1307 code, appears there is one bit placement difference, so that is now
accounted for.
Relnotes: yes
The fdc worker thread was using a one second timeout while waiting for
a new bio to arrive or for the device to detach. However, the driver
already does a wakeup when queueing a new bio or asking the thread to
detach, so the timeout only served to waste CPU time waking up the
thread once a second just so it could go right back to sleep. Use an
infinite timeout instead.
Discussed with: phk
Sponsored by: Netflix
Introduce 2 new flags:
- FL_ENABLE_4B_ADDR (forces the use of 4-byte addresses)
- FL_DISABLE_4B_ADDR (forces the use of 3-byte addresses)
If an SPI flash chip is defined with FL_ENABLE_4B_ADDR in its flags,
then an 'Enter 4-byte mode' command is sent to the chip at attach time
and, later, all commands that require addressing are issued with 4-byte
addresses.
If an SPI flash chip is defined with FL_DISABLE_4B_ADDR in its flags,
then an 'Exit 4-byte mode' command is sent to the chip at attach time
and, later, all commands that require addressing are issued with 3-byte
addresses.
For chips that do not have any of these flags defined the behaviour is
unchanged.
This change also adds support for the MX25L25735F and MX25L25635E chips
(vendor id 0xc2, device id 0x2019), which support 4-byte mode and enables
4-byte mode for them. These are 256Mbit devices (32MiB) and, as such, can
only be fully addressed by using 4-byte addresses.
Approved by: adrian (mentor)
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D5808
the interface.
I know this may be unpopular, but iwn is not yet completely ready for
a transparent firmware restart. I have this thing panic my laptop
reliably because 11n state isn't kept in sync and the TX completion
path ends up trying to free a null node reference.
separate driver. Add support for activating clock and hwreset resources
for these devices when the EXT_RESOURCES option is present.
Reviewed by: andrew, mmel, Emmanuel Vadot <manu@bidouilliste.com>
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D5749
And factor out tcp_lro_rx_done, which deduplicates the same logic with
netinet/tcp_lro.c
Reviewed by: gallatin (1st version), hps, zbb, np, Dexuan Cui <decui microsoft com>
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D5725
The i8254 simulation in Hyper-V is kinda broken and is not available
in Generation 2 Hyper-V VMs, so Hyper-V timer must be registered early
enough so that it can be used to do the TSC freq calibration.
This fixes the notorious warning like this:
calcru: runtime went backwards from 50 usec to 25 usec for pid 0 (kernel)
Submitted by: Dexuan Cui <decui microsoft com>
Reviewed by: kib, sephe
Tested by: kib, sephe
MFC after: 1 week
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D5778
This provides a constant ABI and layout for these structures (especially
struct adapter) avoiding some foot shooting.
Discussed with: np
Sponsored by: Chelsio Communications
nic->num_vf_en is set based on the number of the enabled LMACs.
This number should not be overwritten later by any routine.
Instead it should fail PCI_IOV_ADD_VF() so that available VFs
with the corresponding LMACs will attach whereas other, disabled
VFs will fail with the proper error code.
Error signaling (due to improper number of VFs requested) is also moved
from PCI_IOV_INIT() to PCI_IOV_ADD_VF().
This will be reworked when multiple queue sets are enabled but for
now this is the correct behavior of the driver.
Obtained from: Semihalf
Sponsored by: Cavium
If the driver is not active or link is down the packet could remain
non-writeable. This commit makes all mbufs enqueued to the driver's
ring buffer to have correct attributes.
Pointed out by: wma
Reviewed by: wma
Obtained from: Semihalf
Sponsored by: Cavium
Differential Revision: https://reviews.freebsd.org/D5800
The FDT description is as follows:
- phy-handle, reg, qlm-mode, mac-address are under nodes in bgx0/1 node
- phy nodes (pointed by phy-handle) are under MDIO even though they may
not be connected through to MDIO. In those nodes they do not contain
MAC address or etc.
This commit changes parsing of the FDT nodes for BGX so that it can
obtain correct MAC address for a given PHY.
Reviewed by: wma
Obtained from: Semihalf
Sponsored by: Cavium
Differential Revision: https://reviews.freebsd.org/D5781
- Avoid memory leak when nicvf_tx_mbuf_locked() fails
- Introduce nicvf_xmit_locked() routine that uses drbr_peek(),
drbr_advance() or drbr_putback() for a specific ifnet.
This gives more clear and efficient design as well as
prevents from dropping mbufs that where not sent due to temporary
lack of descriptors.
- Add missing ETHER_BPF_MTAP() hook
Pointed out by: yongari
Reviewed by: wma
Obtained from: Semihalf
Sponsored by: Cavium
Differential Revision: https://reviews.freebsd.org/D5534
Changes introduced to AHCI code adding support for MSI-x
caused interrupt storm on Alpine boards.
This is unintended behaviour so added quirk to omit this functionality.
Reviewed by: mav
Submitted by: Marcin Mazurek <mma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Annapurna Labs
Differential Revision: https://reviews.freebsd.org/D4301
Make it compile only for i386/amd64 for now as it's been tested there.
It's quite possible it'll show up elsewhere and we can enable it
for other architectures later.
Tested:
* PC Engines APU1C4
Submitted by: Daniel Wyatt <daniel@dewyatt.com>
Reviewed by: adrian, loos
Differential Revision: https://reviews.freebsd.org/D5389
It turns out that these will clash very annoyingly with the linux
macros in the linuxkpi layer, so let the wookie^Wlinux win.
The only user that I can find is ath(4), so fix it there too.
Import portions of the PowerPC OF PCI implementation into new file
"ofwpci.c", common for other platforms. The files ofw_pci.c and ofw_pci.h
from sys/powerpc/ofw no longer exist. All required declarations are moved
to sys/dev/ofw/ofwpci.h. This creates a new ofw_pci_write_ivar() function
and modifies some others methods. Most functions contain existing ppc
implementations in the majority unchanged. Now there is no need to have
multiple identical copies of methods for various architectures.
Requested by: jhibbits
Reviewed by: jhibbits, marius
Submitted by: Marcin Mazurek <mma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Annapurna Labs
Differential Revision: https://reviews.freebsd.org/D4879
- Do not mark CSUM_IP_CHECKED and CSUM_IP_VALID on IPv6 packets.
IPv6 does not have checksums by definition.
- Set SCTP packets csum_flags CSUM_SCTP_VALID instead of
CSUM_DATA_VALID and skip csum_data
- Set csum_data simply as 0xffff without byteswap
Pointed out by: yongari
Reviewed by: yongari, wma
Obtained from: Semihalf
Sponsored by: Cavium
Differential Revision: https://reviews.freebsd.org/D5537
It is not necessary as entries are being manipulated under lock.
Reviewed by: wma
Obtained from: Semihalf
Sponsored by: Cavium
Differential Revision: https://reviews.freebsd.org/D5536
This is a no-op currently, but in kernels with earlier AP startup, the
random kthread was trying to use timeouts with sleeps before timers are
working. Wait until SI_SUB_KICK_SCHEDULER to start the random kproc.
Reviewed by: delphij, imp, markm
Approved by: so
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D5712
The graphic mode is noticeably slow on hypervisors, especially
on Hyper-V (1 second to each line).
Submitted by: Dexuan Cui <decui microsoft com>
Reviewed by: kib, sephe, royger (early loader version)
MFC after: 1 week
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D5739
m_unshare passes on the source mbuf's flags as-is to m_getcl and this
results in a leak if the flags include M_NOFREE. The fix is to clear
the bits not listed in M_COPYALL before calling m_getcl. M_RDONLY
should probably be filtered out too but that's outside the scope of this
fix.
Add assertions in the zone_mbuf and zone_pack ctors to catch similar
bugs.
Update netmap_get_mbuf to not pass M_NOFREE to m_getcl. It's not clear
what the original code was trying to do but it's likely incorrect.
Updated code is no different functionally but it avoids the newly added
assertions.
Reviewed by: gnn@
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D5698
- in atags
- in DT blob (by using 'fdt chosen' U-Boot command)
The command line must start with guard's string 'FreeBSD:' and can contain
list of comma separated kenv strings. Also, boot modifier strings from
boot.h are recognised and parsed into boothowto.
The command line must be passed from U-Boot by setting of bootargs variable:
'setenv bootargs FreeBSD:boot_single=1,vfs.root.mountfrom=ufs:/dev/ada0s1a'
followed by 'fdt chosen' (only for DT based boot)
