calling the C functions mtx_enter_hard() and mtx_exit_hard() clobbers them.
Note that %eax is also not call safe, but it is already clobbered due to
cmpxchg. However, now we are back to not compiling again, so these macros
are still left disabled for now.
that of MTX_EXIT. Don't assume that the reg parameter to MTX_ENTER
holds curproc, load it explicitly. Put semi-colons at the end of
the macros to be more consistent and so its harder to forget them
when these change.
SMP problem. Compaq, in their infinite wisdom, forgot to put the IO apic
intpin #0 connection to the 8259 PIC into the mptable. This hack is to
look and see if intpin #0 has *no* table entry and adds a fake ExtInt
entry for the remap routines to use. isa/clock.c will still test the
interrupts. This entry is only ever used on an already broken system.
mpapic.c. This gives us the benefit of C type checking. These functions
are not called in any critical paths and are not used by the interrupt
routines.
spending, which was unused now that all software interrupts have
their own thread. Make the legacy schednetisr use an atomic op
for setting bits in the netisr mask.
Reviewed by: jhb
Also, while here, run up to 32 interrupt sources on APIC systems.
Normalize INTREN/INTRDIS so they are the same on both UP and SMP systems
rather than sometimes a macro, and sometimes a function.
Reviewed by: jhb, jakeb
MPLOCKED macro
(2) Use decimal 12 rather than hex 0xc in an addl
(3) Implement MTX_ENTER for the I386_CPU case
(4) Use semi-colons between instructions to allow MTX_ENTER
and MTX_ENTER_WITH_RECURSION to be assembled
(5) Use incl instead of incw to increment the recusion count
(6) 10 is not a valid label, use 7, 8 and 9 rather than 8, 9 and 10
(7) Sort numeric labels
Submitted by: bde (2, 4, and 5)
process is on the alternate stack or not. For compatibility
with sigstack(2) state is being updated if such is needed.
We now determine whether the process is on the alternate
stack by looking at its stack pointer. This allows a process
to siglongjmp from a signal handler on the alternate stack
to the place of the sigsetjmp on the normal stack. When
maintaining state, this would have invalidated the state
information and causing a subsequent signal to be delivered
on the normal stack instead of the alternate stack.
PR: 22286
-current and RELENG_4 with GENERIC.
NKPT is the number of initial bootstrap page table pages we create for
the kernel during startup. Once VM is up, we resize it as needed, but
with 4G ram, the size of the vm_page_t structures was pushing it over
the limit. The fact that trimmed down kernels boot on 4G ram machines
suggests that we were pretty close to the edge.
The "30" is arbitary, but smaller than the 'nkpt' variable on all
machines that I checked.
timeout. If DIAGNOSTIC is turned on, then display a message to the console
with a map of which CPUs failed to stop or restart. This gives an SMP box
at least a fighting chance of getting into DDB if one of the other CPUs has
interrupts disabled.
counter register in-CPU.
This is to be used as a fast "timer", where linearity is more important
than time, and multiple lines in the linearity caused by multiple CPUs
in an SMP machine is not a problem.
This adds no code whatsoever to the FreeBSD kernel until it is actually
used, and then as a single-instruction inline routine (except for the
80386 and 80486 where it is some more inline code around nanotime(9).
Reviewed by: bde, kris, jhb
syscall compare against a variable sv_minsigstksz in struct
sysentvec as to properly take the size of the machine- and
ABI dependent struct sigframe into account.
The SVR4 and iBCS2 modules continue to have a minsigstksz of
8192 to preserve behavior. The real values (if different) are
not known at this time. Other ABI modules use the real
values.
The native MINSIGSTKSZ is now defined as follows:
Arch MINSIGSTKSZ
---- -----------
alpha 4096
i386 2048
ia64 12288
Reviewed by: mjacob
Suggested by: bde
type of software interrupt. Roughly, what used to be a bit in spending
now maps to a swi thread. Each thread can have multiple handlers, just
like a hardware interrupt thread.
- Instead of using a bitmask of pending interrupts, we schedule the specific
software interrupt thread to run, so spending, NSWI, and the shandlers
array are no longer needed. We can now have an arbitrary number of
software interrupt threads. When you register a software interrupt
thread via sinthand_add(), you get back a struct intrhand that you pass
to sched_swi() when you wish to schedule your swi thread to run.
- Convert the name of 'struct intrec' to 'struct intrhand' as it is a bit
more intuitive. Also, prefix all the members of struct intrhand with
'ih_'.
- Make swi_net() a MI function since there is now no point in it being
MD.
Submitted by: cp
reducues the maintenance load for the mutex code. The only MD portions
of the mutex code are in machine/mutex.h now, which include the assembly
macros for handling mutexes as well as optionally overriding the mutex
micro-operations. For example, we use optimized micro-ops on the x86
platform #ifndef I386_CPU.
- Change the behavior of the SMP_DEBUG kernel option. In the new code,
mtx_assert() only depends on INVARIANTS, allowing other kernel developers
to have working mutex assertiions without having to include all of the
mutex debugging code. The SMP_DEBUG kernel option has been renamed to
MUTEX_DEBUG and now just controls extra mutex debugging code.
- Abolish the ugly mtx_f hack. Instead, we dynamically allocate
seperate mtx_debug structures on the fly in mtx_init, except for mutexes
that are initiated very early in the boot process. These mutexes
are declared using a special MUTEX_DECLARE() macro, and use a new
flag MTX_COLD when calling mtx_init. This is still somewhat hackish,
but it is less evil than the mtx_f filler struct, and the mtx struct is
now the same size with and without mutex debugging code.
- Add some micro-micro-operation macros for doing the actual atomic
operations on the mutex mtx_lock field to make it easier for other archs
to override/optimize mutex ops if needed. These new tiny ops also clean
up the code in some places by replacing long atomic operation function
calls that spanned 2-3 lines with a short 1-line macro call.
- Don't call mi_switch() from mtx_enter_hard() when we block while trying
to obtain a sleep mutex. Calling mi_switch() would bogusly release
Giant before switching to the next process. Instead, inline most of the
code from mi_switch() in the mtx_enter_hard() function. Note that when
we finally kill Giant we can back this out and go back to calling
mi_switch().
in most of the atomic operations. Now for these operations, you can
use the normal atomic operation, you can use the operation with a read
barrier, or you can use the operation with a write barrier. The function
names follow the same semantics used in the ia64 instruction set. An
atomic operation with a read barrier has the extra suffix 'acq', due to
it having "acquire" semantics. An atomic operation with a write barrier
has the extra suffix 'rel'. These suffixes are inserted between the
name of the operation to perform and the typename. For example, the
atomic_add_int() function now has 3 variants:
- atomic_add_int() - this is the same as the previous function
- atomic_add_acq_int() - this function combines the add operation with a
read memory barrier
- atomic_add_rel_int() - this function combines the add operation with a
write memory barrier
- Add 'ptr' to the list of types that we can perform atomic operations
on. This allows one to do atomic operations on uintptr_t's. This is
useful in the mutex code, for example, because the actual mutex lock is
a pointer.
- Add two new operations for doing loads and stores with memory barriers.
The new load operations use a read barrier before the load, and the
new store operations use a write barrier after the load. For example,
atomic_load_acq_int() will atomically load an integer as well as
enforcing a read barrier.
check in the [basic.link] section of the C++ standard wrong. gcc-2.7.2.3
apparently doesn't do the check, so the bug doesn't affect RELENG_3.
PR: 16170, 21427
Submitted by: Max Khon <fjoe@lark.websci.ru> (i386 version)
Discussed with: jdp
return through doreti to handle ast's. This is necessary for the
clock interrupts to work properly.
- Change the clock interrupts on the x86 to be fast instead of threaded.
This is needed because both hardclock() and statclock() need to run in
the context of the current process, not in a separate thread context.
- Kill the prevproc hack as it is no longer needed.
- We really need Giant when we call psignal(), but we don't want to block
during the clock interrupt. Instead, use two p_flag's in the proc struct
to mark the current process as having a pending SIGVTALRM or a SIGPROF
and let them be delivered during ast() when hardclock() has finished
running.
- Remove CLKF_BASEPRI, which was #ifdef'd out on the x86 anyways. It was
broken on the x86 if it was turned on since cpl is gone. It's only use
was to bogusly run softclock() directly during hardclock() rather than
scheduling an SWI.
- Remove the COM_LOCK simplelock and replace it with a clock_lock spin
mutex. Since the spin mutex already handles disabling/restoring
interrupts appropriately, this also lets us axe all the *_intr() fu.
- Back out the hacks in the APIC_IO x86 cpu_initclocks() code to use
temporary fast interrupts for the APIC trial.
- Add two new process flags P_ALRMPEND and P_PROFPEND to mark the pending
signals in hardclock() that are to be delivered in ast().
Submitted by: jakeb (making statclock safe in a fast interrupt)
Submitted by: cp (concept of delaying signals until ast())
- Make softinterrupts (SWI's) almost completely MI, and divorce them
completely from the x86 hardware interrupt code.
- The ihandlers array is now gone. Instead, there is a MI shandlers array
that just contains SWI handlers.
- Most of the former machine/ipl.h files have moved to a new sys/ipl.h.
- Stub out all the spl*() functions on all architectures.
Submitted by: dfr
- Move all register I/O into acpi_io.c
- Move event handling into acpi_event.c
- Reorganise headers into acpivar/acpireg/acpiio
- Move find-RSDT and find-ACPI-owned-memory into acpi_machdep
- Allocate all resources (except those detailed only by AML)
as real resources. Add infrastructure that will make adding
resource support to AML code easy.
- Remove all ACPI #ifdefs in non-ACPI code
- Removed unnecessary includes
- Minor style and commenting fixes
Reviewed by: iwasaki
not work on any real hardware (or fully work on any simulator). Much more
needs to happen before this is actually functional but its nice to see
the FreeBSD copyright message appear in the ia64 simulator.
i386/isa/pcibus.c. This gets -current running again on multiple host->pci
machines after the most recent nexus commits. I had discussed this with
Mike Smith, but ended up doing it slightly differently to what we
discussed as it turned out cleaner this way. Mike was suggesting creating
a new resource (SYS_RES_PCIBUS) or something and using *_[gs]et_resource(),
but IMHO that wasn't ideal as SYS_RES_* is meant to be a global platform
property, not a quirk of a given implementation. This does use the ivar
methods but does so properly. It also now prints the physical pci bus that
a host->pci bridge (pcib) corresponds to.
macros that expand to pass filename and line number information. This is
necessary since we're using inline functions instead of macros now.
Add const to the filename pointers passed througout the mtx and witness
code.
include:
* Mutual exclusion is used instead of spl*(). See mutex(9). (Note: The
alpha port is still in transition and currently uses both.)
* Per-CPU idle processes.
* Interrupts are run in their own separate kernel threads and can be
preempted (i386 only).
Partially contributed by: BSDi (BSD/OS)
Submissions by (at least): cp, dfr, dillon, grog, jake, jhb, sheldonh
suggested fix in PR 12378.
Keep track of all existing pmaps independent of existing processes.
This allows for a process to temporarily connect to a different address
space without the risk of missing an update of the original address space if
the kernel grows.
pmap_pinit2() is no longer needed on the i386 platform but is left as a
stub until the alpha pmap code is updated.
PR: 12378
- stop using the evil 'struct trapframe' argument for mi_startup()
(formerly main()). There are much better ways of doing it.
- do not use prepare_usermode() - setregs() in execve() will do it
all for us as long as the p_md.md_regs pointer is set. (which is
now done in machdep.c rather than init_main.c. The Alpha port did it
this way all along and is much cleaner).
- collect all the magic %cr0 etc register settings into one place and
have the AP's call that instead of using magic numbers (!!) that keep
changing over and over again.
- Make it safe to call kthread_create() earlier, including during the
device probe sequence. It doesn't need the callback mechanism that
NetBSD's version uses.
- kthreads created this way are root-less as they exist before the root
filesystem is mounted. init(1) is set up so that it aquires the root
pointers prior to running. If other kthreads want filesystem acccess
we can make this code more generic.
- set all threads start times once we have decided what time it is.
- init uses a trampoline rather than the evil prepare_usermode() hack.
- kern_descrip.c has a couple of tweaks to deal with forking when there
is no rootdir or cwd etc.
- adjust the early SYSINIT() sequence so that a few prereqisites are in
place. eg: make sure the run queue is initialized before doing forks.
With this, the USB code can easily create a kthread to do the device
tree discovery. (I have tested it, it works nicely).
There are still some open issues before this is truely useful.
- tsleep() does not like working before the clock is running. It
sort-of tries to spin wait, but it can do more useful things now.
- stopping a kthread in kld code at unload time is "interesting" but
we have a solution for that.
The Alpha code needs no changes for this. It already uses pretty much the
same strategies, but a little cleaner.
Don't allow cpu entries in the MP table to contain APIC IDs out of range.
Don't write outside array boundaries if an IO APIC entry in the MP table
contains an APIC ID out of range.
Assign APIC IDs for all IO APICs according to section 3.6.6 in the
Intel MP spec:
- If the current APIC ID on an IO APIC doesn't conflict with other
IO APICs or CPUs, that APIC ID should be used. The copy of the MP
table must be updated if the corresponding APIC ID in the MP table
is different.
- If the current APIC ID was in conflict with other units, the
corresponding APIC ID specified in the MP table is checked for conflict.
- If a conflict is still found then fall back to using a new unique ID.
The copy of the MP table must be updated.
- IDs out of range is considered to be in conflict.
During these operations, the IO_TO_ID array cannot be used, since any
conflict would have caused information loss. The array is then corrected,
since all APIC ID conflicts should have been resolved.
PR: 20312, 18919
errors were normally harmless because they were in unreachable code
and gcc apparently doesn't check the syntax inside asm statements
that it optimizes away.
Further experimentation showed that some Dell 2450 machines with the
prevention kludge installed still got T_RESERVED traps. CPU interrupt
vector 0x7A was observed to be triggered. This might have been the
bitwise OR of two different vectors sent from each of the IOAPICs at
the same time.
IOAPIC #0: 0x68 --> irq 8: RTC timer interrupt
IOAPIC #1: 0x32 --> irq 18: scsi host adapter or network interface
----
0x7a --> T_RESERVED
Both IOAPICs had ID 0.
Appendix B.3 in the MP spec indicates that the operating system is
responsible for assigning unique IDs to the IOAPICs.
The enclosed patch programs the IOAPIC IDs according to the IOAPIC
entries in the MP table.
Submitted by: tegge
to various pmap_*() functions instead of looking up the physical address
and passing that. In many cases, the first thing the pmap code was doing
was going to a lot of trouble to get back the original vm_page_t, or
it's shadow pv_table entry.
Inspired by: John Dyson's 1998 patches.
Also:
Eliminate pv_table as a seperate thing and build it into a machine
dependent part of vm_page_t. This eliminates having a seperate set of
structions that shadow each other in a 1:1 fashion that we often went to
a lot of trouble to translate from one to the other. (see above)
This happens to save 4 bytes of physical memory for each page in the
system. (8 bytes on the Alpha).
Eliminate the use of the phys_avail[] array to determine if a page is
managed (ie: it has pv_entries etc). Store this information in a flag.
Things like device_pager set it because they create vm_page_t's on the
fly that do not have pv_entries. This makes it easier to "unmanage" a
page of physical memory (this will be taken advantage of in subsequent
commits).
Add a function to add a new page to the freelist. This could be used
for reclaiming the previously wasted pages left over from preloaded
loader(8) files.
Reviewed by: dillon
specifies the instruction's operation size. GCC will default to 32-bit
operands reguardless of the prototype (ie, formal parameters' type)
of an inline function.
- Add support for using the PCI BIOS functions for configuration space
accesses, and make this the default.
- Make PNPBIOS the default (obsoletes the PNPBIOS config option).
- Add two new boot-time tunables to disable each of the above.
via sysctl. It's done pretty simply but it should be quite adequate.
Also move SHMMAXPGS from $machine/include/vmparam.h as the comments that
went with it were wrong... we don't allocate KVM space for the pages so
that comment is bogus.. The only practical limit is how much physical
ram you want to lock up as this stuff isn't paged out or swap backed.
includes one of bus_at386.h and bus_pc98.h. Becuase only bus_pc98.h
supports indirect pio and bus_at386.h is identical to old bus.h, there
is no functional change in PC-AT's kernels. That is, it cannot cause
performance loss.
Submitted by: nyan
Reviewed by: imp
bde and luoqi provided useful comments for earlier version.
syscall path inward. A system call may select whether it needs the MP
lock or not (the default being that it does need it).
A great deal of conditional SMP code for various deadended experiments
has been removed. 'cil' and 'cml' have been removed entirely, and the
locking around the cpl has been removed. The conditional
separately-locked fast-interrupt code has been removed, meaning that
interrupts must hold the CPL now (but they pretty much had to anyway).
Another reason for doing this is that the original separate-lock for
interrupts just doesn't apply to the interrupt thread mechanism being
contemplated.
Modifications to the cpl may now ONLY occur while holding the MP
lock. For example, if an otherwise MP safe syscall needs to mess with
the cpl, it must hold the MP lock for the duration and must (as usual)
save/restore the cpl in a nested fashion.
This is precursor work for the real meat coming later: avoiding having
to hold the MP lock for common syscalls and I/O's and interrupt threads.
It is expected that the spl mechanisms and new interrupt threading
mechanisms will be able to run in tandem, allowing a slow piecemeal
transition to occur.
This patch should result in a moderate performance improvement due to
the considerable amount of code that has been removed from the critical
path, especially the simplification of the spl*() calls. The real
performance gains will come later.
Approved by: jkh
Reviewed by: current, bde (exception.s)
Some work taken from: luoqi's patch
was using them exits.
Don't allow a user process to cause the kernel to take a TRCTRAP on a
user space address.
Reviewed by: jlemon, sef
Approved by: jkh
the low level interrupt handler number should be used. Change
setup_apic_irq_mapping() to allocate low level interrupt handler X (Xintr${X})
for any ISA interrupt X mentioned in the MP table.
Remove an assumption in the driver for the system clock (clock.c) that
interrupts mentioned in the MP table as delivered to IOAPIC #0 intpin Y
is handled by low level interrupt handler Y (Xintr${Y}) but don't assume
that low level interrupt handler 0 (Xintr0) is used.
Don't allocate two low level interrupt handlers for the system clock.
Reviewed by: NOKUBI Hirotaka <hnokubi@yyy.or.jp>
is an application space macro and the applications are supposed to be free
to use it as they please (but cannot). This is consistant with the other
BSD's who made this change quite some time ago. More commits to come.
The UPAGES have not been there since Jan '96, but the hole was preserved
for BSD/OS binary compatability. This has been fixed other ways (%ebx
now has a pointer to PS_STRINGS), and the stack is nowhere near where
it used to be so this hack isn't required anymore.
and extend. The new function containing the code is named schedclock()
as in NetBSD, but it has slightly different semantics (it already handles
incrementation of p->p_cpticks, and it should handle any calling frequency).
Agreed with in principle by: dufault
to use a locked cmpexg when unlocking a lock that we already hold, since
nobody else can touch the lock while we hold it. Second, it is not
necessary to use a locked cmpexg when locking a lock that we already
hold, for the same reason. These changes will allow MP locks to be used
recursively without impacting performance.
Modify two procedures that are called only by assembly and are already
NOPROF entries to pass a critical argument in %edx instead of on the
stack, removing a significant amount of code from the critical path
as a consequence.
Reviewed by: Alfred Perlstein <bright@wintelcom.net>, Peter Wemm <peter@netplex.com.au>
Historically, the documentation of extended asm was lacking, namely you
should NOT specify the same register as an input, and a clobber.
If the register is clobbered, it should be specified as an output as well,
e.g., by linking input and output through the "number" notation.
(Beware of lvalues, some local variables needed...)
URL:http://egcs.cygnus.com/faq.html
In versions up to egcs-1.1.1, the compiler did not even warn about it,
but it was liable to output bad code. Newer egcs are pickier and simply
refuse to swallow such code.
Note, since *addr changes, it needs to be an output operand.
We might be excessive in saying that all memory has changed.
Obtained from: OpenBSD
w/extra thanks to Marc Espie <Marc.Espie@liafa.jussieu.fr>
the countdown register.
this should not be necessary but there are broken laptops that
do not restore the countdown register on resume.
when it happnes, it messes up the hardclock interval and system clock,
which leads to the infamous "calcru: negative time" problem.
Submitted by: kjc, iwasaki
Reviewed by: Steve O'Hara-Smith <steveo@eircom.net> and committers.
Obtained from: PAO3
* Change the hack used on the alpha for mapping devices into DENSE or
BWX memory spaces to a simpler one. Its still a hack and should be
a seperate api to explicitly map the resource.
* Add $FreeBSD$ as necessary.
can provide the correct context to each signal handler.
Fix broken sigsuspend(): don't use p_oldsigmask as a flag, use SAS_OLDMASK
as we did before the linuxthreads support merge (submitted by bde).
Move ps_sigstk from to p_sigacts to the main proc structure since signal
stack should not be shared among threads.
Move SAS_OLDMASK and SAS_ALTSTACK flags from sigacts::ps_flags to proc::p_flag.
Move PS_NOCLDSTOP and PS_NOCLDWAIT flags from proc::p_flag to procsig::ps_flag.
Reviewed by: marcel, jdp, bde
o Remove unused defines from genassym.c that were needed
by the trampoline.
o Add load_gs_param function to support.s that catches
a fault when %gs is loaded with an invalid descriptor.
The function returns EFAULT in that case.
o Remove struct trapframe from mcontext_t and replace it
with the list of registers.
o Modify sendsig and sigreturn accordingly.
This commit contains a patch by bde.
Reviewed by: luoqi, jdp
struct sigcontext and ucontext_t/mcontext_t are defined in such
a way that both (ie struct sigcontext and ucontext_t) can be
passed on to sigreturn. The signal handler is still given a
ucontext_t for maximum flexibility.
For backward compatibility sigreturn restores the state for the
alternate signal stack from sigcontext.sc_onstack and not from
ucontext_t.uc_stack. A good way to determine which value the
application has set and thus which value to use, is still open
for discussion.
NOTE: This change should only affect those binaries that use
sigcontext and/or ucontext_t. In the source tree itself
this is only doscmd. Recompilation is required for those
applications.
This commit also fixes a lot of style bugs without hopefully
adding new ones.
NOTE: struct sigaltstack.ss_size now has type size_t again. For
some reason I changed that into unsigned int.
Parts submitted by: bde
sigaltstack bug found by: bde
-----------------------------
By introducing a new sigframe so that the signal handler operates
on the new siginfo_t and on ucontext_t instead of sigcontext, we
now need two version of sendsig and sigreturn.
A flag in struct proc determines whether the process expects an
old sigframe or a new sigframe. The signal trampoline handles
which sigreturn to call. It does this by testing for a magic
cookie in the frame.
The alpha uses osigreturn to implement longjmp. This means that
osigreturn is not only used for compatibility with existing
binaries. To handle the new sigset_t, setjmp saves it in
sc_reserved (see NOTE).
the struct sigframe has been moved from frame.h to sigframe.h
to handle the complex header dependencies that was caused by
the new sigframe.
NOTE: For the i386, the size of jmp_buf has been increased to hold
the new sigset_t. On the alpha this has been prevented by
using sc_reserved in sigcontext.
the OS does FXSAVE/FXRESTOR instructions (fast FPU save/restore) during
context switching and also enables SIMD since this enables saving the
extra CPU context that isn't saved with normal FPU regs. The other
enables the SIMD instructions to use exception 16 (FPU) error reporting.
Note, this doesn't turn on SIMD, just defines the bits.
1. Move definitions of struct i386_*_args to the header file sysarch.h,
since they are part of the sysarch API. struct i386_get_ldt_args and
i386_set_ldt_args were identical, therefore make them into one
struct i386_ldt_args. Libc should use these definitions as well.
2. Return a more sensible EOPNOTSUPP for unknown operations.
Reviewed by: marcel
into two parts - one to do the bsfl and the other to convert the result
(base 0) to ffs()-like (base 1) in inline C. This enables the optimizer
to be a lot smarter in certain cases, like where it knows that the argument
is non-zero and we want ffs(known non zero arg) - 1. This appears to
produce identical code to the old inline when the argument is unknown.
that are linked into the kernel. The KLD compilation options are
changed to call these functions, rather than in-lining the
atomic operations.
This approach makes atomic operations from KLDs significantly
faster on UP systems (though somewhat slower on SMP systems).
PR: i386/13111
Submitted by: peter.jeremy@alcatel.com.au
0x40 and then access data stored in real-mode segment 0x40, even when
called in protected mode. Microsoft unfortunately coddle these individuals,
and so must we if we want to run their code.
This change works around GPFs in some APM and PnP BIOS implementations.
Obtained from: Linux
- Add support for calling 32-bit code in other segments
- Add support for calling 16-bit protected mode code
Update APM to use this facility.
Submitted by: jlemon
equivalent to SYS_RES_MEMORY for x86 but for alpha, the rman_get_virtual()
address of the resource is initialised to point into either dense-mapped
or bwx-mapped space respectively, allowing direct memory pointers to be
used to device memory.
Reviewed by: Andrew Gallatin <gallatin@cs.duke.edu>
macros) to the signal handler, for old-style BSD signal handlers as
the second (int) argument, for SA_SIGINFO signal handlers as
siginfo_t->si_code. This is source-compatible with Solaris, except
that we have no <siginfo.h> (which isn't even mentioned in POSIX
1003.1b).
An rather complete example program is at
http://www3.cons.org/cracauer/freebsd-signal.c
This will be added to the regression tests in src/.
This commit also adds code to disable the (hardware) FPU from
userconfig, so that you can use a software FP emulator on a machine
that has hardware floating point. See LINT.
Change "void *" to "volatile TYPE *", improving type safety
and eliminating some warnings (e.g., mp_machdep.c rev 1.106).
cpufunc.h:
Eliminate setbits. As defined, it's not precisely correct;
and it's redundant. (Use atomic_set_int instead.)
ipl_funcs.c:
Use atomic_set_int instead of setbits.
systm.h:
Include atomic.h.
Reviewed by: bde
the caller to specify a function to be guarded between an entry and exit
barrier, as well as pre- and post-barrier functions.
The primary use for this function is synchronised update of per-cpu private
data. The implementation is almost (but not quite) MI; with a better
mechanism for masking per-CPU interrupts it could probably be hoisted.
Reviewed by: peter (partially)
with respect to interrupts on UP systems. (The upgrade from gcc 2.7.x
to egcs 1.1.2 produced at least one non-atomic code sequence in
swap_pager_getpages.)
In addition, the primitives are now SMP-safe, but only on SMPs. (For
portability between SMPs and UPs, modules are compiled with the SMP-safe
versions.)
Submitted by: dillon and myself
Reviewed by: bde
than a review, this was a nice puzzle.
This is supposed to be binary and source compatible with older
applications that access the old FreeBSD-style three arguments to a
signal handler.
Except those applications that access hidden signal handler arguments
bejond the documented third one. If you have applications that do,
please let me know so that we take the opportunity to provide the
functionality they need in a documented manner.
Also except application that use 'struct sigframe' directly. You need
to recompile gdb and doscmd. `make world` is recommended.
Example program that demonstrates how SA_SIGINFO and old-style FreeBSD
handlers (with their three args) may be used in the same process is at
http://www3.cons.org/tmp/fbsd-siginfo.c
Programs that use the old FreeBSD-style three arguments are easy to
change to SA_SIGINFO (although they don't need to, since the old style
will still work):
Old args to signal handler:
void handler_sn(int sig, int code, struct sigcontext *scp)
New args:
void handler_si(int sig, siginfo_t *si, void *third)
where:
old:code == new:second->si_code
old:scp == &(new:si->si_scp) /* Passed by value! */
The latter is also pointed to by new:third, but accessing via
si->si_scp is preferred because it is type-save.
FreeBSD implementation notes:
- This is just the framework to make the interface POSIX compatible.
For now, no additional functionality is provided. This is supposed
to happen now, starting with floating point values.
- We don't use 'sigcontext_t.si_value' for now (POSIX meant it for
realtime-related values).
- Documentation will be updated when new functionality is added and
the exact arguments passed are determined. The comments in
sys/signal.h are meant to be useful.
Reviewed by: BDE
behavior slightly.
If machine/bus.h is included, but neither bus_memio.h nor bus_pio.h
are included, then behave as if both were included.
This won't change existing drivers, all of which include one or more
of bus_{p,mem}io.h, but will allow drivers from other systems to come
over with fewer changes. I freely admit that this might not be
optimal for some drivers, but those drivers can be optimized for
FreeBSD after the initial bringup happens.
Without the change, there is a bug that preclude drivers from
compiling with strange warning/errors.
I've been running this here for a while now w/o ill effects.
Reviewed by: gibbs
Not objected to by: bde, arch@ list.
automatically hacks on the active copy of the IDT if f00f_hack()
has changed it. This also allows simplifications in setidt().
This fixes breakage of FP exception handling by rev.1.55 of
sys/kernel.h. FP exceptions were sent to npx.c's probe handlers
because npx.c "restored" the old handlers to the wrong copy of the
IDT. The SYSINIT for f00f_hack() was purposely run quite late to
avoid problems like this, but it is bogusly associated with the
SYSINIT for proc0 so it was moved with the latter.
Problem reported and fix tested by: Martin Cracauer <cracauer@cons.org>
implicitly LOCK'ed instruction), so there shouldn't be any harm in making
it volatile pointer compatable for one of the users of it. It seems to
generate the same code regardless.
for elf kernels (it is broken for all kernels due to lack of egcs support).
Renaming of many assembler labels is avoided by declaring by declaring
the labels that need to be visible to gprof as having type "function"
and depending on the elf version of gprof being zealous about discarding
the others. A few type declarations are still missing, mainly for SMP.
PR: 9413
Submitted by: Assar Westerlund <assar@sics.se> (initial parts)
range attributes after they have been extracted from the master.
Hook up the i686 MP code to do this for each AP.
Be more careful about printing the default memory type for the i686.
Suggestions from: luoqi
- %fs register is added to trapframe and saved/restored upon kernel entry/exit.
- Per-cpu pages are no longer mapped at the same virtual address.
- Each cpu now has a separate gdt selector table. A new segment selector
is added to point to per-cpu pages, per-cpu global variables are now
accessed through this new selector (%fs). The selectors in gdt table are
rearranged for cache line optimization.
- fask_vfork is now on as default for both UP and SMP.
- Some aio code cleanup.
Reviewed by: Alan Cox <alc@cs.rice.edu>
John Dyson <dyson@iquest.net>
Julian Elischer <julian@whistel.com>
Bruce Evans <bde@zeta.org.au>
David Greenman <dg@root.com>
the address of the ps_strings structure to the process via %ebx.
For other kinds of binaries, %ebx is still zeroed as before.
Submitted by: Thomas Stephens <tas@stephens.org>
Reviewed by: jdp
In particular, replace the unused field pmap::pm_flag by pmap::pm_active,
which is a bit mask representing which processors have the pmap activated.
(Thus, it is a simple Boolean on UPs.)
Also, eliminate an unnecessary memory reference from cpu_switch()
in swtch.s.
Assisted by: John S. Dyson <dyson@iquest.net>
Tested by: Luoqi Chen <luoqi@watermarkgroup.com>,
Poul-Henning Kamp <phk@critter.freebsd.dk>
bootblocks in order to boot the kernel after this! Also note that this
change breaks BSDI BSD/OS compatibility.
Also increased default NKPT to 17 so that FreeBSD can boot on machines
with >=2GB of RAM. Booting on machines with exactly 4GB requires other
patches, not included.
numbers as chars or use bogus casts in an attempt to unmisrepresnt
them. In top, don't assume that 0xff is the only negative cpu
number when cpu numbers are (mis)represented.
is the preparation step for moving pmap storage out of vmspace proper.
Reviewed by: Alan Cox <alc@cs.rice.edu>
Matthew Dillion <dillon@apollo.backplane.com>
put it, just like on the Alpha. It was wrong to load it at the
fixed address 0x08000000. That should only be done if the dynamic
linker is an executable (not a shared object) with a specific load
address encoded in the object file itself.
This fixes the recent breakage in the Linux emulator.
to an architecture-specific value defined in <machine/elf.h>. This
solves problems on large-memory systems that have a high value for
MAXDSIZ.
The load address is controlled by a new macro ELF_RTLD_ADDR(vmspace).
On the i386 it is hard-wired to 0x08000000, which is the standard
SVR4 location for the dynamic linker.
On the Alpha, the dynamic linker is loaded MAXDSIZ bytes beyond
the start of the program's data segment. This is the same place
a userland mmap(0, ...) call would put it, so it ends up just below
all the shared libraries. The rationale behind the calculation is
that it allows room for the data segment to grow to its maximum
possible size.
These changes have been tested on the i386 for several months
without problems. They have been tested on the Alpha as well,
though not for nearly as long. I would like to merge the changes
into 3.1 within a week if no problems have surfaced as a result of
them.
Sun implemented iBCS2 compatibility on Solaris >= 2.6: The emulator
runs in user-mode, patching the LDT so that client programs making
syscalls through the old iBCS2 call gate get handled by the emulator
process. Unemulated syscalls therefore need their own call-gate that
bypasses the emulator. Sun chose LDT entry 4 to implement this, which
is what we've been using as LUDATA_SEL, so we need to change LUDATA_SEL
if we want to run Solaris executables.
Discussed with: Mike Smith
installed.
Remove cpu_power_down, and replace it with an entry at the end of the
SHUTDOWN_FINAL queue in the only place it's used (APM).
Submitted by: Some ideas from Bruce Walter <walter@fortean.com>
The code was originaly contributed by Kelly Yancey
<kbyanc@freedomnet.com> in PR i386/6269 and revised by Akio Morita
<amorita@meadow.scphys.kyoto-u.ac.jp> and me. Test was performed by
Akio Morita and Toshiomi Moriki <moriki@db.is.kyushu-u.ac.jp>.
- Fix stylistic bug in identcpu.c.
- Update copyright in initcpu.c
- Fix typo in LINT.
PR: 6269 and 6270
The last consumer of this code (the old SCSI system) has left us and
the CAM code does it's own bouncing. The isa dma system has been
doing it's own bouncing for a while too.
Reviewed by: core
and set_regs() but for the floating point register state. The code
is stolen from procfs_machdep.c, and moved out of there into
machdep.c.
These functions are needed for generating ELF core dumps.
the relevant characteristics of the native machine, for building
and checking Elf_Ehdr structures.
Add structures to represent ELF "note" headers. Add defines for the
note types used in ELF core files.
the executable file, so it will work for both a.out and ELF format
files. I have split the object format specific code into separate
source files. It's cleaner than it was before, but it's still
pretty crufty.
Don't cheat on your make world for this update. A lot of things
have to be rebuilt for it to work, including the compiler and all
of the profiled libraries.
and use this when masking/unmasking interrupts.
Maintain a mapping from (iopaic number, int pin) tuple to irq number,
and use this when configuring devices and programming the ioapics.
Previous code assumed that irq number was equal to int pin number, and
that the ioapic number was 0.
Don't let an AP enter _cpu_switch before all local apics are initialized.
- moved definition of MACHINE_ARCH from cpu.h to parm.h as alpha.
- Added definitions of _MACHINE and _MACHINE_ARCH.
- Added hw.ispc98. The hw.ispc98 is 1 in PC98 kernel and is 0 in
IBM-PC kernel.
Discussed with: John Birrell <jb@FreeBSD.ORG>
Add some overflow checks to read/write (from bde).
Change all modifications to vm_page::flags, vm_page::busy, vm_object::flags
and vm_object::paging_in_progress to use operations which are not
interruptable.
Reviewed by: Bruce Evans <bde@zeta.org.au>
in a SMP system. Unexpected things could happen if each cpu
has a different ldt setting and one cpu tries to use value
of currentldt set by another cpu.
The fix is to move currentldt to the per-cpu area. It includes
patches I filed in PR i386/6219 which are also user ldt related.
PR: i386/7591, i386/6219
Submitted by: Luoqi Chen <luoqi@watermarkgroup.com>
applications. Here's how it works.
The kernel should include <machine/elf.h> to get the definitions
for the native architecture. It can reference the various ELF
structures with generic names like Elf_Sym, Elf_Shdr, etc. A define
__ELF_WORD_SIZE is also available with the value 32 or 64 as
appropriate for the native architecture.
Generic applications should include <elf.h>, which is just a wrapper
for <machine/elf.h>.
Applications such as object file dumpers that need to deal with
foreign ELF files can include <sys/elf32.h> and/or <sys/elf64.h>.
Both can be included from the same source file if desired. The
structure names must be referenced using wordsize-specific names
like Elf32_Sym, Elf64_Shdr, etc.
I haven't change the alpha stuff, but I haven't broken it either.
Cast pointers to (vm_offset_t) instead of to (u_long) (as before) or to
(uintptr_t)(void *) (as would be more correct). Don't cast vm_offset_t's
to (u_long) just to do arithmetic on them.
mp_machdep.c:
Cast pointers to (uintptr_t) instead of to (u_long). Don't forget
to cast pointers to (void *) first or to recover from integral
possible integral promotions, although this is too much work for
machine-dependent code.
vm code generally avoids warnings for pointer vs long size mismatches
by using vm_offset_t to represent pointers; pmap.c often uses plain
`unsigned int' instead of vm_offset_t and didn't use u_long elsewhere,
but this style was messed up by code apparently imported from mp_machdep.c.
suitable for holding object pointers (ptrint_t -> uintptr_t).
Added corresponding signed type (intptr_t). Changed/added
corresponding non-C9x types for function pointers to match. Don't
use nonstandard types to implement these types, and don't comment
on them in <machine/types.h>.
just to ensure 32-bit variables. Doing so broke and/or pessimized
i386's with 64-bit longs (unnecessary use of 64-bit variables
caused remarkably few problems in C code, but the inline asm here
tended to fail because there are no 64-bit registers). Since the
interfaces here are very machine-dependent and shouldn't be used
outside of the kernel, use a standard types of "known" width instead
of fixed-width types.
Changed all quad_t's to u_int64_t's. quad_t isn't standard, and
using signed types for 64-bit registers was bogus (but made no
difference).
least unsuitable for holding an object pointer. This should have been
used to fix warnings about casts between pointers and ints on alphas.
Moved corresponding existing general typedef (fptrint_t) for function
pointers from the i386 <machine/profile.h> to a kernel-only typedef
in <machine/types.h>. Kludged libc/gmon/mcount.c so that it can
still see this typedef.
Clean up (or if antipodic: down) some of the msgbuf stuff.
Use an inline function rather than a macro for timecounter delta.
Maintain process "on-cpu" time as 64 bits of microseconds to avoid
needless second rollover overhead.
Avoid calling microuptime the second time in mi_switch() if we do
not pass through _idle in cpu_switch()
This should reduce our context-switch overhead a bit, in particular
on pre-P5 and SMP systems.
WARNING: Programs which muck about with struct proc in userland
will have to be fixed.
Reviewed, but found imperfect by: bde
available. The per-cpu variable ss_tpr has been replaced by ss_eflags.
This reduced the number of interrupts sent to the wrong CPU, due to
the cpu having the global lock being inside a critical region.
Remove some unneeded manipulation of tpr register in mplock.s.
Adjust code in mplock.s to be aware of variables on the stack being
destroyed by MPgetlock if GRAB_LOPRIO is defined.
update of cpu usage as shown by top when one process is cpu bound
(no system calls) while the system is otherwise idle (except for top).
Don't attempt to switch to the BSP in boot(). If the system was idle when
an interrupt caused a panic, this won't work. Instead, switch to the BSP
in cpu_reset.
Remove some spurious forward_statclock/forward_hardclock warnings.
ints. Remove some no longer needed casts. Initialize the per-cpu
global data area using the structs rather than knowing too much about
layout, alignment, etc.
- Attempt to handle PCI devices where the interrupt is
an ISA/EISA interrupt according to the mp table.
- Attempt to handle multiple IO APIC pins connected to
the same PCI or ISA/EISA interrupt source. Print a
warning if this happens, since performance is suboptimal.
This workaround is only used for PCI devices.
With these two workarounds, the -SMP kernel is capable of running on
my Asus P/I-P65UP5 motherboard when version 1.4 of the MP table is disabled.
has been some bitrot and incorrect assumptions in the vfs_bio code. These
problems have manifest themselves worse on NFS type filesystems, but can
still affect local filesystems under certain circumstances. Most of
the problems have involved mmap consistancy, and as a side-effect broke
the vfs.ioopt code. This code might have been committed seperately, but
almost everything is interrelated.
1) Allow (pmap_object_init_pt) prefaulting of buffer-busy pages that
are fully valid.
2) Rather than deactivating erroneously read initial (header) pages in
kern_exec, we now free them.
3) Fix the rundown of non-VMIO buffers that are in an inconsistent
(missing vp) state.
4) Fix the disassociation of pages from buffers in brelse. The previous
code had rotted and was faulty in a couple of important circumstances.
5) Remove a gratuitious buffer wakeup in vfs_vmio_release.
6) Remove a crufty and currently unused cluster mechanism for VBLK
files in vfs_bio_awrite. When the code is functional, I'll add back
a cleaner version.
7) The page busy count wakeups assocated with the buffer cache usage were
incorrectly cleaned up in a previous commit by me. Revert to the
original, correct version, but with a cleaner implementation.
8) The cluster read code now tries to keep data associated with buffers
more aggressively (without breaking the heuristics) when it is presumed
that the read data (buffers) will be soon needed.
9) Change to filesystem lockmgr locks so that they use LK_NOPAUSE. The
delay loop waiting is not useful for filesystem locks, due to the
length of the time intervals.
10) Correct and clean-up spec_getpages.
11) Implement a fully functional nfs_getpages, nfs_putpages.
12) Fix nfs_write so that modifications are coherent with the NFS data on
the server disk (at least as well as NFS seems to allow.)
13) Properly support MS_INVALIDATE on NFS.
14) Properly pass down MS_INVALIDATE to lower levels of the VM code from
vm_map_clean.
15) Better support the notion of pages being busy but valid, so that
fewer in-transit waits occur. (use p->busy more for pageouts instead
of PG_BUSY.) Since the page is fully valid, it is still usable for
reads.
16) It is possible (in error) for cached pages to be busy. Make the
page allocation code handle that case correctly. (It should probably
be a printf or panic, but I want the system to handle coding errors
robustly. I'll probably add a printf.)
17) Correct the design and usage of vm_page_sleep. It didn't handle
consistancy problems very well, so make the design a little less
lofty. After vm_page_sleep, if it ever blocked, it is still important
to relookup the page (if the object generation count changed), and
verify it's status (always.)
18) In vm_pageout.c, vm_pageout_clean had rotted, so clean that up.
19) Push the page busy for writes and VM_PROT_READ into vm_pageout_flush.
20) Fix vm_pager_put_pages and it's descendents to support an int flag
instead of a boolean, so that we can pass down the invalidate bit.
f00f_hack has run.
Use the global r_idt descriptor in f00f_hack when in SMP mode,
so the APs find the relocated interrupt descriptor table.
Submitted by: Partially from David A Adkins <adkin003@tc.umn.edu>
interrupts are masked, and EOI is sent iff the corresponding ISR bit
is set in the local apic. If the CPU cannot obtain the interrupt
service lock (currently the global kernel lock) the interrupt is
forwarded to the CPU holding that lock.
Clock interrupts now have higher priority than other slow interrupts.
the signal handling latency for cpu-bound processes that performs very
few system calls.
The IPI for forcing an additional software trap is no longer dependent upon
BETTER_CLOCK being defined.
2) Do not unnecessarily force page blocking when paging
pages out.
3) Further improve swap pager performance and correctness,
including fixing the paging in progress deadlock (except
in severe I/O error conditions.)
4) Enable vfs_ioopt=1 as a default.
5) Fix and enable the page prezeroing in SMP mode.
All in all, SMP systems especially should show a significant
improvement in "snappyness."
in a way identically as before.) I had problems with the system properly
handling the number of vnodes when there is alot of system memory, and the
default VM_KMEM_SIZE. Two new options "VM_KMEM_SIZE_SCALE" and
"VM_KMEM_SIZE_MAX" have been added to support better auto-sizing for systems
with greater than 128MB.
Add some accouting for vm_zone memory allocations, and provide properly
for vm_zone allocations out of the kmem_map. Also move the vm_zone
allocation stats to the VM OID tree from the KERN OID tree.
Highlights:
* Simple model for underlying hardware.
* Hardware basis for timekeeping can be changed on the fly.
* Only one hardware clock responsible for TOD keeping.
* Provides a real nanotime() function.
* Time granularity: .232E-18 seconds.
* Frequency granularity: .238E-12 s/s
* Frequency adjustment is continuous in time.
* Less overhead for frequency adjustment.
* Improves xntpd performance.
Reviewed by: bde, bde, bde
of the various ad-hoc schemes.
2) When bringing in UPAGES, the pmap code needs to do another vm_page_lookup.
3) When appropriate, set the PG_A or PG_M bits a-priori to both avoid some
processor errata, and to minimize redundant processor updating of page
tables.
4) Modify pmap_protect so that it can only remove permissions (as it
originally supported.) The additional capability is not needed.
5) Streamline read-only to read-write page mappings.
6) For pmap_copy_page, don't enable write mapping for source page.
7) Correct and clean-up pmap_incore.
8) Cluster initial kern_exec pagin.
9) Removal of some minor lint from kern_malloc.
10) Correct some ioopt code.
11) Remove some dead code from the MI swapout routine.
12) Correct vm_object_deallocate (to remove backing_object ref.)
13) Fix dead object handling, that had problems under heavy memory load.
14) Add minor vm_page_lookup improvements.
15) Some pages are not in objects, and make sure that the vm_page.c can
properly support such pages.
16) Add some more page deficit handling.
17) Some minor code readability improvements.
Move sigjmp_buf and jmp_buf structure definitions to machine/setjmp.h
so that i386 can continue to use int as the basic register type and
alpha can use long. Bruce was concerned about possible differing
alignment. I've left the definition of _JBLEN in machine/setjmp.h
even though Bruce's example used the number directly. I don't know if
any other code relies on _JBLEN, so I left it to avoid potential
breakage.
- A nonprofiling version of s_lock (called s_lock_np) is used
by mcount.
- When profiling is active, more registers are clobbered in
seemingly simple assembly routines. This means that some
callers needed to save/restore extra registers.
- The stack pointer must have space for a 'fake' return address
in idle, to avoid stack underflow.
noticed some major enhancements available for UP situations. The number
of UP TLB flushes is decreased much more than significantly with these
changes. Since a TLB flush appears to cost minimally approx 80 cycles,
this is a "nice" enhancement, equiv to eliminating between 40 and 160
instructions per TLB flush.
Changes include making sure that kernel threads all use the same PTD,
and eliminate unneeded PTD switches at context switch time.
in <machine/cpu.h>. Moved the declarations to <machine/cputypes.h>.
Fixed style bugs in the moved code. Fixed everything that depended on
the nested include. Don't include <machine/cpu.h> (in the changed files)
unless something in it is used directly.
and fixed everything that dependended on it being declared in the old
place. It is used in "machine-independent" code in subr_prof.c.
Moved declaration of btext from subr_prof.c to <machine/cpu.h>. It
is machine-dependent.
in a P6 SMP system. Some MB bios'es don't set the registers up correctly
for the AP's. Additionally, set the memory between 0xa0000 and 0xbffff
as write combining.
PR: 4486
Submitted by: tegge@idi.ntnu.no (Tor Egge)
Implement a function is_adapter_memory() in order to determine what
should nto be dumped at all. Currently, only populated with the ``ISA
memory hole''. Adapter regions of other busses should be added.
holding CPU along with the lock. When a CPU fails to get the lock
it compares its own id to the holder id. If they are the same it
panic()s, as simple locks are binary, and this would cause a deadlock.
Controlled by smptests.h: SL_DEBUG, ON by default.
Some minor cleanup.
Add a simplelock to deal with disable_intr()/enable_intr() as used in UP kernel.
UP kernel expects that this is enough to guarantee exclusive access to
regions of code bracketed by these 2 functions.
Add a simplelock to bracket clock accesses in clock.c: clock_lock.
Help from: Bruce Evans <bde@zeta.org.au>
smp_active = 1 used to indicate that the system had frozen previously
started AP's, while smp_active = 0 was "AP's not yet started". I have split
this into smp_started (which is set when the AP's come online), and
smp_active is left for turning on/off AP scheduling.
- We now have enough per-cpu idle context, the real idle loop has been
revived (cpu's halt now with nothing to do).
- Some preliminary support for running some operations outside the
global lock (eg: zeroing "free but not yet zeroed pages") is present
but appears to cause problems. Off by default.
- the smp_active sysctl now behaves differently. It's merely a 'true/false'
option. Setting smp_active to zero causes the AP's to halt in the idle
loop and stop scheduling processes.
- bootstrap is a lot safer. Instead of sharing a statically compiled in
stack a number of times (which has caused lots of problems) and then
abandoning it, we use the idle context to boot the AP's directly. This
should help >2 cpu support since the bootlock stuff was in doubt.
- print physical apic id in traps.. helps identify private pages getting
out of sync. (You don't want to know how much hair I tore out with this!)
More cleanup to follow, this is more of a checkpoint than a
'finished' thing.
Added a new variable, 'bsp_apic_ready', which is set as soon as the bootstrap
CPU has initialized its local APIC. Conditionalize the GENSPLR functions
to call ss_lock ONLY after bsp_apic_ready is TRUE; This should prevent
any problems with races between the time the 1st AP becomes ready and the
time smp_active is set.