This is used by the 'athsurvey' command to print out channel survey
statistics - % busy times transmit, receive and airtime.
It's as buggy and incomplete as the rest of the HAL survey support -
notably, tying into the ANI code to read channel stats and occasionally
getting garbage counters isn't very nice. It also doesn't (yet!) get
channel survey information during a scan. But it's good enough for
basic air-time debugging, which is why I'm committing it in this state.
Tested:
* AR9380, STA mode
path.
* For now there's no exposed control over classic / LNA antenna diversity,
so just stub them out. Adding this will take quite a bit of time.
* Add a function to fetch the CTS timeout.
PR: kern/198558
Highlights:
- Multiple verbs API updates
- Support for RoCE, RDMA over ethernet
All hardware drivers depending on the common infiniband stack has been
updated aswell.
Discussed with: np @
Sponsored by: Mellanox Technologies
MFC after: 1 month
I don't like having it in this function; I may migrate it to ar9300_freebsd.c
at some point to keep the HAL code pollution down.
This allows ANI to be disabled via a sysctl.
Tested:
* AR9331, STA/TDMA modes
This is a custom FreeBSD HAL method that is used by the TDMA code
to program the beacon timers directly without any guesswork/assumptions
by the HAL.
This brings up basic TDMA master/slave support on the AR9380 HAL,
however there are other issues preventing it from being stable.
(I'm seeing beacon interval instability, which may be due to
busy 2GHz air, but also may be due to some HAL configuration
issues with regards to ANI, or hardware timer programming, etc.)
Tested:
* AR9331 (Carambola2), STA, AP, adhoc and TDMA master mode.
The QCA9565 can have RFKILL on GPIO Pin 11, and thus we need to configure
it up correctly or the NIC may not function.
I'm not sure why the AR9382 can't use GPIO 8 / GPIO 11 ; it's likely
hooked up to some external LNA or filter. The real solution is to
make it only block pin 8 / pin 11 for AR9382, but the AR9382 probes
like an AR9380. Sigh.
Submitted by: Anthony Jenkins <scoobi_doo@yahoo.com>
I've been sitting on this for a year or so now; I've finally
tested it on enough devices to be reasonably sure it won't
cause too much drama. But, if you see issues, please email me.
Tested (all STA mode):
PCIe:
* AR9380
* AR9390
* AR9580
* AR9462
* AR9485
SoC:
* QCA9550
* AR9331
* AR9342
hw.x2apic_enable tunable allows disabling it from the loader prompt.
To closely repeat effects of the uncached memory ops when accessing
registers in the xAPIC mode, the x2APIC writes to MSRs are preceeded
by mfence, except for the EOI notifications. This is probably too
strict, only ICR writes to send IPI require serialization to ensure
that other CPUs see the previous actions when IPI is delivered. This
may be changed later.
In vmm justreturn IPI handler, call doreti_iret instead of doing iretd
inline, to handle corner conditions.
Note that the patch only switches LAPICs into x2APIC mode. It does not
enables FreeBSD to support > 255 CPUs, which requires parsing x2APIC
MADT entries and doing interrupts remapping, but is the required step
on the way.
Reviewed by: neel
Tested by: pho (real hardware), neel (on bhyve)
Discussed with: jhb, grehan
Sponsored by: The FreeBSD Foundation
MFC after: 2 months
If structure packed as __packed clang (and probably gcc) generates
code that loads word fields (e.g. tx_pos) byte-by-byte and if it's
modified by VideoCore in the same time as ARM loads the value result
is going to be mixed combination of bytes from previous value and
new one.
the ia_array field of struct ar9300_ini_array const, and removing the
const-dropping casts. No functional change.
Reviewed by: adrian
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D1725
"MODULE_VERSION" macro definition. Remove the redefinition of the
"MODULE_VERSION" macro from the Linux kernel compatibility API.
MFC after: 1 month
Reported by: np@
Sponsored by: Mellanox Technologies
AR9462/AR9565.
This and some upcoming changes to the HAL for these chips should
address some of the signal sensitivity reported by users.
Tested:
* AR9462 (WB222), STA mode
Obtained from: Linux ath9k
AR9565 (Aphrodite.) These need to use the MCI routines, not
the legacy 2-wire / 3-wire bluetooth coexistence methods.
Tested:
* AR9462 (WB222); STA mode
socket-buffer implementations, introduce a return value for MCLGET()
(and m_cljget() that underlies it) to allow the caller to avoid testing
M_EXT itself. Update all callers to use the return value.
With this change, very few network device drivers remain aware of
M_EXT; the primary exceptions lie in mbuf-chain pretty printers for
debugging, and in a few cases, custom mbuf and cluster allocation
implementations.
NB: This is a difficult-to-test change as it touches many drivers for
which I don't have physical devices. Instead we've gone for intensive
review, but further post-commit review would definitely be appreciated
to spot errors where changes could not easily be made mechanically,
but were largely mechanical in nature.
Differential Revision: https://reviews.freebsd.org/D1440
Reviewed by: adrian, bz, gnn
Sponsored by: EMC / Isilon Storage Division
images into the kernel as currently included into iwn6000g2{a,b}fw.ko
and delete the old files, missed in r254199 and r259135 respectively.
MFC after: 3 days
Without this fix, the vnet was NULL and would crash.
This fix is similar to what was done inside the ioctl handler for PF.
Tested by:
(1) Boot a kernel with "options VIMAGE" enabled
(2) Type:
echo "map lo0 from 10.0.0.0/24 to ! 10.0.0.0/24 -> 127.0.0.1/32" > /etc/ipnat.rules ; service ipnat onerestart
PR: 176992
Differential Revision: https://reviews.freebsd.org/D1191
Reviewed by: cy
lib/libngatm:
sys/contrib/ngatm/netnatm/saal/saal_sscop.c:4030:32: error: 'break' is bound to current loop, GCC binds it to the enclosing loop [-Werror,-Wgcc-compat]
} while(sn < sscop->vr_h && !QFIND(&sscop->rbuf, sn));
^
sys/contrib/ngatm/netnatm/saal/saal_sscop.c:173:4: note: expanded from macro 'QFIND'
break; \
^
1 error generated.
The idea is to remove any ambiguity by replacing the macro with an
equivalent static inline function.
Reviewed by: emaste, rpaulo
See also: http://reviews.llvm.org/D2518
Differential Revision: https://reviews.freebsd.org/D1188
Mellanox hardware driver(s):
- Properly name an inclusion guard
- Fix compile warnings regarding unsigned enums
- Add two new sysctl nodes
- Remove all empty linux header files
- Make an error printout more verbose
- Use "mod_delayed_work()" instead of
cancelling and starting a timeout.
- Implement more Linux scatterlist
functions.
MFC after: 3 days
Sponsored by: Mellanox Technologies
This fixes when an IP address mapping is put in the hostmap table for
sticky NAT rules, it ends up having the wrong byte order.
Obtained from: ipfilter CVS repo (r1.102), NetBSD CVS repo (r1.12)
These variants have a few differences from the default AR9485 NIC,
namely:
* a non-default antenna switch config;
* slightly different RX gain table setup;
* an external XLNA hooked up to a GPIO pin;
* (and not yet done) RSSI threshold differences when
doing slow diversity.
To make this possible:
* Add the PCI device list from Linux ath9k, complete with vendor and
sub-vendor IDs for various things to be enabled;
* .. and until FreeBSD learns about a PCI device list like this,
write a search function inspired by the USB device enumeration code;
* add HAL_OPS_CONFIG to the HAL attach methods; the HAL can use this
to initialise its local driver parameters upon attach;
* copy these parameters over in the AR9300 HAL;
* don't default to override the antenna switch - only do it for
the chips that require it;
* I brought over ar9300_attenuation_apply() from ath9k which is cleaner
and easier to read for this particular NIC.
This is a work in progress. I'm worried that there's some post-AR9380
NIC out there which doesn't work without the antenna override set as
I currently haven't implemented bluetooth coexistence for the AR9380
and later HAL. But I'd rather have this code in the tree and fix it
up before 11.0-RELEASE happens versus having a set of newer NICs
in laptops be effectively RX deaf.
Tested:
* AR9380 (STA)
* AR9485 CUS198 (STA)
Obtained from: Qualcomm Atheros, Linux ath9k
struct ifnet if_oqdrops.
Some netgraph modules used ifqueue w/o ifnet. Accounting of queue drops
is simply removed from them. There were no API to read this statistic.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
The firmware is from the Linux firmware git repository; the intel
licence is the same as other firmware blobs.
Tested: iwn1: <Intel Centrino Wireless-N 100> mem 0xf4800000-0xf4801fff irq 19 at device 0.0 on pci5
hardware driver update from Mellanox Technologies.
- Remove empty files from the OFED Linux Emulation layer.
- Fix compile warnings related to printf() and the "%lld" and "%llx"
format specifiers.
- Add some missing 2-clause BSD copyrights.
- Add "Mellanox Technologies, Ltd." to list of copyright holders.
- Add some new compatibility files.
- Fix order of uninit in the mlx4ib module to avoid crash at unload
using the new module_exit_order() function.
MFC after: 1 week
Sponsored by: Mellanox Technologies
If powersave is enabled and there are any transitions to network
or full sleep - even if they're pretty damned brief - eventually
something messes up somewhere and the bus glue between the AR9331
SoC and the AR9331 wifi stops working. It shows up as stuck DMA
and LOCAL_TIMEOUT interrupts.
Both ath9k and the reference driver does a full chip reset if things
get stuck.
So:
* teach the AR9330 HAL about the force_full_reset option I added a
couple of years ago;
* if the chip is currently in full-sleep, do a full-reset;
* if TX DMA and/or RX DMA are still enabled (eg, they did get
stuck during reset) then do a full-reset.
Tested:
* AR9331 SoC, STA mode
This includes:
o All directories named *ia64*
o All files named *ia64*
o All ia64-specific code guarded by __ia64__
o All ia64-specific makefile logic
o Mention of ia64 in comments and documentation
This excludes:
o Everything under contrib/
o Everything under crypto/
o sys/xen/interface
o sys/sys/elf_common.h
Discussed at: BSDcan
This is loosly based on Xorg changeset f57bc0e by Christian
Zander.
Submitted by: Wolf Ramovsky <wolf.ramovsky gmail.com>
via core (peter)
MFC after: 2 weeks
to be consistent with mutex destruction in ipf_log_soft_destroy(). As a
result mutex destruction in ipf_log_soft_fini() is redundant.
Approved by: glebius (mentor)
Obtained from: darrenr (author)
This seems to probe/attach as an AR9485 and thus nothing else besides
adding the device id seems to be required.
ath0: <Atheros AR1111> mem 0xf4800000-0xf487ffff irq 19 at device 0.0 on pci5
ath0: [HT] enabling HT modes
ath0: [HT] enabling short-GI in 20MHz mode
ath0: [HT] 1 stream STBC receive enabled
ath0: [HT] 1 RX streams; 1 TX streams
ath0: AR9485 mac 576.1 RF5110 phy 1926.8
ath0: 2GHz radio: 0x0000; 5GHz radio: 0x0000
The NIC I have here is a 1 antenna, 2GHz only device.
Thankyou to Jim Thompson <jim@netgate.com> for the AR1111 NIC.
Tested:
* AR1111 (pretending not to be an AR9485, but failing miserably);
STA mode with powersave.
Relnotes: yes
Sponsored by: Netgate
ip_auth.c to ip_auth.h. ip_frag_soft_t moves from ip_frag.c to
ip_frag.h. mlfk_ipl.c creates sysctl MIBs that reference control blocks
that are dynamically created when IP Filter is loaded. This necessitated
creating them on-the-fly rather than statically at compile time.
Approved by: glebius (mentor)
Import xz-embedded from git.
This is from commit hash '6a8a2364434763a033781f6b2a605ace9a021013'.
This makes it possible to use CRC64 but for now it's intentionally
not added to build.
- Use counter(9) for rt_pksent (former rt_rmx.rmx_pksent). This
removes another cache trashing ++ from packet forwarding path.
- Create zini/fini methods for the rtentry UMA zone. Via initialize
mutex and counter in them.
- Fix reporting of rmx_pksent to routing socket.
- Fix netstat(1) to report "Use" both in kvm(3) and sysctl(3) mode.
The change is mostly targeted for stable/10 merge. For head,
rt_pksent is expected to just disappear.
Discussed with: melifaro
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
in net, to avoid compatibility breakage for no sake.
The future plan is to split most of non-kernel parts of
pfvar.h into pf.h, and then make pfvar.h a kernel only
include breaking compatibility.
Discussed with: bz
- Provide pf_altq.h that has only stuff needed for ALTQ.
- Start pf.h, that would have all constant values and
eventually non-kernel structures.
- Build ALTQ w/o pfvar.h, include if_var.h, that before
came via pollution.
- Build tcpdump w/o pfvar.h.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
Update the OFED Infiniband core to the version supplied in Linux
version 3.7.
The update to OFED is nearly all additional defines and functions
with the exception of the addition of additional parameters to
ib_register_device() and the reg_user_mr callback.
In addition the ibcore (Infiniband core) and ipoib (IP over Infiniband)
have both been made into completely loadable modules to facilitate
testing of the OFED stack in FreeBSD.
Finally the Mellanox Infiniband drivers are now updated to the
latest version shipping with Linux 3.7.
Submitted by: Mellanox FreeBSD driver team:
Oded Shanoon (odeds mellanox.com),
Meny Yossefi (menyy mellanox.com),
Orit Moskovich (oritm mellanox.com)
Approved by: re
This driver is based on Linux 3.8 and a previous effort by kan@.
More informations about this project can be found on the FreeBSD wiki:
https://wiki.freebsd.org/AMD_GPU
The driver is split into:
sys/dev/drm2:
The driver sources.
sys/modules/drm2/radeonkmw:
The driver main kernel module's Makefile.
sys/modules/drm2/radeonkmsfw:
All firmware kernel module Makefiles. There's one directory and one
Makefile for each firmware.
sys/contrib/dev/drm2/radeonkmsfw:
All firmware binary sources.
tools/tools/drm/radeon
Tools to update firmwares or regenerate some headers.
Merging the driver to FreeBSD 9.x may be possible but not a priority for
now.
Help from: kib@, kan@
Tested by: avg@, kwm@, ray@,
Alexander Yerenkow <yerenkow@gmail.com>,
Anders Bolt-Evensen <andersbo87@me.com>,
Denis Djubajlo <stdedjub@googlemail.com>,
J.R. Oldroyd <fbsd@opal.com>,
Mikaël Urankar <mikael.urankar@gmail.com>,
Pierre-Emmanuel Pédron <pepcitron@gmail.com>,
Sam Fourman Jr. <sfourman@gmail.com>,
Wade <wade-is-great@live.com>,
(probably other I forgot...)
HW donations: kyzh, Yakaz
