This code base on lpc code. Ralink RT1310 is oem from 5V Technologies.
RT1310 is ARM926EJS(arm5t).
Tested:
* Buffalo WZR2-G300N
Submitted by: Hiroki Mori <yamori813@yahoo.co.jp>
Reviewed by: mizhka
Differential Revision: https://reviews.freebsd.org/D7238
before we increase irq again, or we'd end up choosing an irq, and then
really using the next one, even if it's not available.
Also in the inner loop, correct the end check so that we check every irq,
even the last one.
This makes the msk(4) adapter able to use MSI on Softiron Overdrive 1000.
Add early init handler, which comprises various internal
bus optimisations for Armada 38x SoC's. Magic values used
due to undocumented registers.
Submitted by: Marcin Wojtas <mw@semihalf.com>,
Arnaud Ysmal <arnaud.ysmal@stormshield.eu>
Obtained from: Semihalf, Stormshield
Sponsored by: Stormshield
Differential revision: https://reviews.freebsd.org/D10219
Part of PL310 erratum 727915 in pl310_wbinv_range() was
executed uncoditionally for all possible controllers'
revisions. This patch adds appropriate condition, since
extra operations are required only for revisions between
r2p0 and r3p0.
Submitted by: Marcin Wojtas <mw@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: meloun-miracle-cz
Differential revision: https://reviews.freebsd.org/D10221
Introduce machine-dependent part of the arm/pl310 driver for
Armada 38x SoCs. Add prefetch and power savings configuration.
Submitted by: <arnaud.ysmal@stormshield.eu>
Obtained from: Stormshield
Sponsored by: Stormshield
Differential revision: https://reviews.freebsd.org/D10220
Memory space reserved for pmap_kernel_l2dtable_kva and
pmap_kernel_l2ptp_kva has not been taken into account in
original code. All the memory reserved from kernel space by
pmap_alloc_specials() function called in pmap_bootstrap()
should be mapped initially by initarm(). To create initial
mapping initarm() function reserves proper number of l2 page
tables. However the number of the l2 page tables does not take
into account memory for: pmap_kernel_l2ptp_kva,
pmap_kernel_l2dtable_kva, crashdumpmap, etc.
Submitted by: Grzegorz Bernacki <gjb@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: meloun-miracle-cz
Differential revision: https://reviews.freebsd.org/D10217
VM_KMEM_SIZE_MAX allows to limit kmem arena size. In our case this was
necessary, as decreasing size of kmem_arena leaves more space for
kernel_arena.
kernel_arena is pool used for contigmalloc (in effect, DMA) allocations,
which failed on Armada38x. This resulted in 'no memory errors'
(e.g. USB_ERR_NOMEM errors) and failure of whole system. The need for
greater size of kernel_arena probably comes from more peripherals making
use of busdma.
Value used as upper limit is half of the default value
(0x1399a000).
Submitted by: Wojciech Macek <wma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential revision: https://reviews.freebsd.org/D10216
in place. To do per-cpu stats, convert all fields that previously were
maintained in the vmmeters that sit in pcpus to counter(9).
- Since some vmmeter stats may be touched at very early stages of boot,
before we have set up UMA and we can do counter_u64_alloc(), provide an
early counter mechanism:
o Leave one spare uint64_t in struct pcpu, named pc_early_dummy_counter.
o Point counter(9) fields of vmmeter to pcpu[0].pc_early_dummy_counter,
so that at early stages of boot, before counters are allocated we already
point to a counter that can be safely written to.
o For sparc64 that required a whole dummy pcpu[MAXCPU] array.
Further related changes:
- Don't include vmmeter.h into pcpu.h.
- vm.stats.vm.v_swappgsout and vm.stats.vm.v_swappgsin changed to 64-bit,
to match kernel representation.
- struct vmmeter hidden under _KERNEL, and only vmstat(1) is an exclusion.
This is based on benno@'s 4-year old patch:
https://lists.freebsd.org/pipermail/freebsd-arch/2013-July/014471.html
Reviewed by: kib, gallatin, marius, lidl
Differential Revision: https://reviews.freebsd.org/D10156
imx6 based on a single cortex-a7 core. Other changes to imx6 drivers
and support code are needed to fully support the imx6ul.
Also fix an indentation glitch committed in the prior change.
driver for imx6. Some newer dts source puts the GIC node at the root
instead of under /soc, so look in both places. Also, sometimes the GIC
node doesn't list itself as its own interrupt-parent, allow that too.
At this point, INTRNG is not going away (the option may go away, but the
code is not), so we no longer need code to support workarounds that handled
the lack of INTRNG functionality.
The MFC will include a compat definition of smp_no_rendevous_barrier()
that calls smp_no_rendezvous_barrier().
Reviewed by: gnn, kib
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D10313
FreeBSD's DTS contained only one PL050 node and driver considered it to
be PS/2 keyboard. In reality PL050 is a PS/2 port that pushes bytes to/from
the periphers connected to it. New DTS contains two nodes and QEMU emulates
keyboard connected to port #0 and mouse connected to port #1. Since there
is no way to say what's connected to port by checking DTS we hardcode
this knowledge in the driver: it assumes keyboard on port #0 and ignores
port #1 altogether.
Also QEMU defaults emulated keyboard to scan code set 2 while driver used
to work with scan code set 1 so when initializing driver make sure keyboard
is switched to scan code set 1
Scope of this change is somewhat larger than just converting to INTRNG.
The reason for this is that INTRNG support required switching from custom
to upstream DTS because custom DTS didn't have interrup routing information.
This switch caused rewrite of PCI and CLCD drivers and adding SCM module.
List of changes in this commit:
- Enable INTRNG and switch to versatile-pb.dts
- Add SCM driver that controls various peripheral devices like LCD or
PCI controller. Previously registers required for power-up and
configuring peripherals were part of their respective nodes. Upstream
DTS has dedicated node for SCM
- Convert PL190 driver to INTRNG
- Convert Versatile SIC (secondary interrupt controller) to INTRNG
- Refactor CLCD driver to use SCM API to power up and configuration
- Refactor PCI driver to use SCM API to enable controller
- Refactor PCI driver to use interrupt map provided in DTS for
interrupt routing. As a result it fixes broken IRQ routing and
it's no longer required to run QEMU with "-global versatile_pci.broken-irq-mapping=1"
command-line arguments
Fallback to Linux video interface bindings introduced in r313068 worked
with then current DTS but that DTS turned out to be not conformant to
the the bindings spec. DTS import in r314854 fixed the conformancy but
broke the functionality. This commit syncs up functionality to the actual
spec.
Reported by: manu@
cfumass(4) is not usable if usfs(4) is loaded or compiled into the
kernel. Remove usfs so that the user may kldload the USB mass storage
target they prefer.
PR: 218169
Reviewed by: trasz, hselasky (no objection)
Relnotes: Yes
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D10153
I fixed this in 1997, but the fix was over-engineered and fragile and
was broken in 2003 if not before. i386 parameters were copied to 8
other arches verbatim, mostly after they stopped working on i386, and
mostly without the large comment saying how the values were chosen on
i386. powerpc has a non-verbatim copy which just changes the uncritical
parameter and seems to add a sign extension bug to it.
Just treat negative offsets as offsets if they are no more negative than
-db_offset_max (default -64K), and remove all the broken parameters.
-64K is not very negative, but it is enough for frame and stack pointer
offsets since kernel stacks are small.
The over-engineering was mainly to go more negative than -64K for the
negative offset format, without affecting printing for more than a
single address.
Addresses in the top 64K of a (full 32-bit or 64-bit) address space
are now printed less well, but there aren't many interesting ones.
For arches that have many interesting ones very near the top (e.g.,
68k has interrupt vectors there), there would be no good limit for
the negative offset format and -64K is a good as anything.
We don't have enouch space to store full VFP context within mcontext
stucture. Due to this:
- follow i386/amd64 way and store VFP state outside of the mcontext_t
but point to it. Use the size of VFP state structure as an 'magic'
indicator of the saved VFP state presence.
- teach set_mcontext() about this external storage.
- for signal delivery, store VFP state to expanded 'struct sigframe'.
Submited by: Andrew Gierth (initial version)
PR: 217611
MFC after: 2 weeks
FreeBSD uses upstream DTB for RPi3 build and compatibility string for
i2c device is different there. Add this new string to compatibility data.
Reported by: Karl Denninger
MFC after: 3 days
- in mcontext_t, rename newer used 'union __vfp' to equaly sized 'mc_spare'.
Space allocated by 'union __vfp' is too small and cannot hold full
VFP context.
- move structures defined in fp.h to more appropriate headers.
- remove all unused VFP structures.
MFC after: 2 weeks
Newbus handles multiple equally named device classes without problems,
so there is no reason to use slightly cryptic "<foo>_shdci" for them.
In contrast, the driver module name must be unique, so "<foo>_shdci"
is the right name for it.
matches static binaries.
Interpretation of the 'static' there is that the binary must not
specify an interpreter. In particular, shared objects are matched by
the brand if BI_CAN_EXEC_DYN is also set.
This improves precision of the brand matching, which should eliminate
surprises due to brand ordering.
Revert r315701.
Discussed with and tested by: ed (previous version)
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
CloudABI executables are statically linked and don't have an
interpreter. Setting the interpreter path to NULL used to work
previously, but r314851 introduced code that checks the string
unconditionally. Running CloudABI executables now causes a null pointer
dereference.
Looking at the rest of imgact_elf.c, it seems various other codepaths
already leaned on the fact that the interpreter path is set. Let's just
go ahead and pick an obviously incorrect interpreter path to appease
imgact_elf.c.
MFC after: 1 week
calculated at runtime based on how long it takes to set up an event in
hardware. This fixes the intermittant 1-minute hang at boot on imx5
systems, and also the occasional oversleeping while running. It doesn't
affect imx6 systems, which use different hardware for eventtimers.
It turns out that it usually takes about 30 timer ticks to set up the timer
compare register, and the old hard-coded minimum period was 10 ticks. On
the rare occasions when a timeout event that short was set up, we'd miss
the event and have to wait about 64 seconds for counter rollover before
the compare interrupt would fire.
Instead of just hardcoding a new bigger value, the code now measures the
time it takes to do the register read/write sequence to set up the compare
register, scales it up by 1.5x to be safe, and calculates the minimum event
period from the result. In the real world, the minimum period works out to
about 750 nanoseconds on imx5 hardware.
It turns out to be surprisingly expensive to access the gpt hardware (on the
order of 150ns per read/write). To cut down on the overhead of setting up
each eventtimer event, eliminate read-modify-write sequences to manage the
compare interrupt enable, by keeping a shadow copy of the hardware register
and only writing to the hardware when the enable bits really change.
cleanups enabled by that:
- The only thing left in imx_gptvar.h was the softc, which IMO never
should have been in there at all. Move it into the driver, and
delete the header file.
- Remove several unneeded #includes from the driver.
- Change imx_gpt_softc from global to static (it's used by DELAY()), and
don't redundantly static-initialize it to NULL.
supply the addresses for the DPLL register blocks) by hard-coding the
addresses in the driver source code. Yes, this is just as bad an idea as
it sounds, but we have no choice.
In the early days of using fdt data, when we were making up our own data
for each board, we defined 4 sets of memory mapped registers in the data.
The vendor-supplied data only provides the address of the CCM register
block, but not the 3 DPLL blocks. The linux driver has the DPLL physical
addresses (which differ by SOC type) hard-coded in the driver, and we
have no choice but to do the same thing if we want to run with the vendor-
supplied fdt data.
So now we use bus_space_map() to make the DPLL blocks accessible, choosing
the set of fixed addresses to map based on the soc id.
It seems to be old code from the armv6 project branch that never had a
kernel config.
Reviewed by: mmel
Sponsored by: ABT Systems Lrd
Differential Revision: https://reviews.freebsd.org/D7166
nodes from the DTB by default. This will allow us to enumerate the CPUs
without hard coding the CPU count into code.
Reviewed by: br
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D9827
be migrated to this and will allow the removal of this option.
Reviewed by: ian
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D9907
the default partition, eMMC v4.41 and later devices can additionally
provide up to:
1 enhanced user data area partition
2 boot partitions
1 RPMB (Replay Protected Memory Block) partition
4 general purpose partitions (optionally with a enhanced or extended
attribute)
Of these "partitions", only the enhanced user data area one actually
slices the user data area partition and, thus, gets handled with the
help of geom_flashmap(4). The other types of partitions have address
space independent from the default partition and need to be switched
to via CMD6 (SWITCH), i. e. constitute a set of additional "disks".
The second kind of these "partitions" doesn't fit that well into the
design of mmc(4) and mmcsd(4). I've decided to let mmcsd(4) hook all
of these "partitions" up as disk(9)'s (except for the RPMB partition
as it didn't seem to make much sense to be able to put a file-system
there and may require authentication; therefore, RPMB partitions are
solely accessible via the newly added IOCTL interface currently; see
also below). This approach for one resulted in cleaner code. Second,
it retains the notion of mmcsd(4) children corresponding to a single
physical device each. With the addition of some layering violations,
it also would have been possible for mmc(4) to add separate mmcsd(4)
instances with one disk each for all of these "partitions", however.
Still, both mmc(4) and mmcsd(4) share some common code now e. g. for
issuing CMD6, which has been factored out into mmc_subr.c.
Besides simply subdividing eMMC devices, some Intel NUCs having UEFI
code in the boot partitions etc., another use case for the partition
support is the activation of pseudo-SLC mode, which manufacturers of
eMMC chips typically associate with the enhanced user data area and/
or the enhanced attribute of general purpose partitions.
CAVEAT EMPTOR: Partitioning eMMC devices is a one-time operation.
- Now that properly issuing CMD6 is crucial (so data isn't written to
the wrong partition for example), make a step into the direction of
correctly handling the timeout for these commands in the MMC layer.
Also, do a SEND_STATUS when CMD6 is invoked with an R1B response as
recommended by relevant specifications. However, quite some work is
left to be done in this regard; all other R1B-type commands done by
the MMC layer also should be followed by a SEND_STATUS (CMD13), the
erase timeout calculations/handling as documented in specifications
are entirely ignored so far, the MMC layer doesn't provide timeouts
applicable up to the bridge drivers and at least sdhci(4) currently
is hardcoding 1 s as timeout for all command types unconditionally.
Let alone already available return codes often not being checked in
the MMC layer ...
- Add an IOCTL interface to mmcsd(4); this is sufficiently compatible
with Linux so that the GNU mmc-utils can be ported to and used with
FreeBSD (note that due to the remaining deficiencies outlined above
SANITIZE operations issued by/with `mmc` currently most likely will
fail). These latter will be added to ports as sysutils/mmc-utils in
a bit. Among others, the `mmc` tool of the GNU mmc-utils allows for
partitioning eMMC devices (tested working).
- For devices following the eMMC specification v4.41 or later, year 0
is 2013 rather than 1997; so correct this for assembling the device
ID string properly.
- Let mmcsd.ko depend on mmc.ko. Additionally, bump MMC_VERSION as at
least for some of the above a matching pair is required.
- In the ACPI front-end of sdhci(4) describe the Intel eMMC and SDXC
controllers as such in order to match the PCI one.
Additionally, in the entry for the 80860F14 SDXC controller remove
the eMMC-only SDHCI_QUIRK_INTEL_POWER_UP_RESET.
OKed by: imp
Submitted by: ian (mmc_switch_status() implementation)
as kernel drivers and their dependency onto mmc(4); this allows for
incrementing the mmc(4) module version but also for entire omission
of these bridge declarations for mmccam(4) in a single place, i. e.
in dev/mmc/bridge.h.
comments, marking unused parameters as such, style(9), whitespace,
etc.
o In the mmc(4) bridges and sdhci(4) (bus) front-ends:
- Remove redundant assignments of the default bus_generic_print_child
device method (I've whipped these out of the tree as part of r227843
once, but they keep coming back ...),
- use DEVMETHOD_END,
- use NULL instead of 0 for pointers.
o Trim/adjust includes.
RPi3 cpufreq is more like that on RPi2. Setting arm frequency
above min (say, "sysctl hw.cpufreq.arm_freq=600000001") turns on
turbo mode, and the firmware automatically raises voltage, sets
frequency to max 1200MHz, and throttle when overheat, etc.
Swap if/else parts and use SOC_BCM2835 def so RPi3 can share the
same cpufreq logic as RPi2, instead of falling to that for RPi.
Submitted by: Jia-Shiun Li <jiashiun@gmail.com>
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D9640
Renumber cluase 4 to 3, per what everybody else did when BSD granted
them permission to remove clause 3. My insistance on keeping the same
numbering for legal reasons is too pedantic, so give up on that point.
Submitted by: Jan Schaumann <jschauma@stevens.edu>
Pull Request: https://github.com/freebsd/freebsd/pull/96
This adds clocks support for the aw_ccung on the A31 SoC.
Newer DTS files require this.
All the clocks except two CSI are defined and exported on the clock domain.
The PLL_DDR clock have an update bit which need to be set after changing
the value, add the possibility to define one for NKMP clocks.
This allow us to add the missing clocks.
We now have the full list of clocks created under the clock domain.
This is required for FDT's standard "reg-io-width" property
(similar to "reg-shift" property) found in many DTS files.
This fixes operation on Altera Arria 10 SOC Development Kit,
where standard ns8250 uart allows 4-byte access only.
Reviewed by: kan, marcel
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D9785
Since Linux 4.9-4.10 DTS doesn't have clocks under /clocks but only a ccu node.
Currently only H3 is supported with almost the same state as HEAD.
(video pll aren't supported for now but we don't support video).
This driver and clocks will also be used for other SoC (A64, A31, H5, H2 etc ...)
Reviewed by: jmcneill
Differential Revision: https://reviews.freebsd.org/D9517
Convert PCIe hot plug support over to asking the firmware, if any, for
permission to use the HotPlug hardware. Implement pci_request_feature
for ACPI. All other host pci connections to allowing all valid feature
requests.
Sponsored by: Netflix
if the fdt data doesn't provide a gpio pin for reading the write protect
switch and also doesn't contain a "wp-disable" property.
In r311735 the long-bitrotted code in this driver for using the non-
standard fdt "mmchs-wp-gpio-pin" property was replaced with new common
support code for handling write-protect and card-detect gpio pins. The
old code never found a property with that name, and the logic was to
assume that no gpio pin meant that the card was not write protected.
The new common code behaves differently. If there is no fdt data saying
what to do about sensing write protect, the value in the standard SDHCI
PRESENT_STATE register is used. On this hardware, if there is no signal
for write protect muxed into the sd controller then that bit in the
register indicates write protect.
The real problem here is the fdt data, which should contain "wp-disable"
properties for eMMC and micro-sd slots where write protect is not even
an option in the hardware, but we are not in control of that data, it
comes from linux. So we have to make the same flawed assumption in our
driver that the corresponding linux driver has: no info means no protect.
Reported by: several users on the arm@ list
Pointy hat: me, for not testing enough before committing r311735
This enables the PHY circuitry for UTMI+ level 2 and 3, and sets the
flag to tell the ehci code that the root hub has a transaction translator
in it. For imx6 we can use the standard ehci_get_port_speed_portsc()
function to find out what speed device is connected to the port.
On arm64 use atomics. Then, both arm and arm64 do not need a critical
section around update. Replace all cpus loop by CPU_FOREACH().
This brings arm and arm64 counter(9) implementation closer to current
amd64, but being more RISC-y, arm* version cannot avoid atomics.
Reported by: Alexandre Martins <alexandre.martins@stormshield.eu>
Reviewed by: andrew
Tested by: Alexandre Martins, andrew
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
identify_arm_cpu() in sys/arm/arm/identcpu-v4.c incorrectly uses a
u_int8_t variable to store the result of cpu_get_control().
It should really use a u_int variable, the same way as done for cpu_ident()
in the same function, as both cpuid and control registers are 32-bit..
This issue causes users of identcpu-v4 to incorrectly report things such as
icache status (bit 12 in cpu control register) and basically anything
defined in bits above bit 7 :-)
Reviewed by: manu
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D9460
The types are for the byte offset and page index in vm object. They
are similar to off_t, which is defined as 64bit MI integer. Using MI
definitions will allow to provide consistent MD values of vm
object-related maximum sizes.
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
- Use new option SMP_ON_UP instead of (mis)using specific CPU type.
By this, any SMP kernel can be compiled with SMP_ON_UP support.
- Enable runtime detection of CPU multiprocessor extensions only
if SMP_ON_UP option is used. In other cases (pure SMP or UP),
statically compile only required variant.
- Don't leak multiprocessor instructions to UP kernel.
- Correctly handle data cache write back to point of unification.
DCCMVAU is supported on all armv7 cpus.
- For SMP_ON_UP kernels, detect proper TTB flags on runtime.
Differential Revision: https://reviews.freebsd.org/D9133
Historically AM335x LCDC driver used non-standard "hdmi" property to
refer to HDMI framer. There is no such thing in upstream DTS, so to
handle both cases fallback to bindings described in
bindings/media/video-interfaces.txt in Linux documentation.
We still make some assumptions that are not universally true: we
assume that if remote endpoint is available it's going to be HDMI
framer. Which is true for AM335x-based devices currently supported
but may be not true for some custom hardware.
MFC after: 1 week
register, in addition to configuring it as input with the pinmux driver.
There was a control register bit commented as "no desc in datasheet". A
later revision of the manual reveals the bit to be an input/output control
for the timer pin. In addition to configuring capture or pulse mode, you
apparently have to separately configure the pin direction in the timer
control register.
Before this change, the timer block was apparently driving a signal onto a
pad configured by pinmux as input. Capture mode still accidentally worked
for me during testing because I was using a very strong signal source that
just out-muscled the weaker drive from the misconfigured pin.
Commit r312747 ("Setup decoding windows for ARMADA38X") resulted
in build failing for Marvell platforms, which don't have AHCI controller.
This patch provides a fix by adding dummy functions for such cases.
On the occasion rename register dump routine to decode_win_ahci_dump,
in order to avoid confusion.
Submitted by: Marcin Wojtas <mw@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
- Replace pcpu_find(curcpu) with get_pcpu(), which is much
more direct.
- Remove armv4 pcpu fields which I added in r286296 but never
needed to use.
- armv6 pc_qmap_addr was leftover from the old armv6 pmap
implementation. Rename it and put it to use in the new one.
Noted by: skra
Reviewed by: skra
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D9312
This file provides support for AHCI mode on Armada38x
and adds new optional AHCI device to arm/mv/files.mv.
Submitted by: Konrad Adamczyk <ka@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: zbb
Differential revision: https://reviews.freebsd.org/D9222
It is necesarry to open memory windows on internal bus for
AHCI driver to work correctly.
Submitted by: Konrad Adamczyk <ka@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: zbb
Differential revision: https://reviews.freebsd.org/D9220
Configure decoding windows only for devices with
enabled nodes in FDT.
Submitted by: Konrad Adamczyk <ka@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: zbb
Differential revision: https://reviews.freebsd.org/D9219
* Currently supports only Armada38X family but other Marvell SoC's
can be added if needed.
* Provides temperature is C deg.
* To print the temperature one can use:
sysctl dev.armada_thermal.0.temperature
Submitted by: Zbigniew Bodek <zbb@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential revision: https://reviews.freebsd.org/D9217
mappings for armv6 pmap zero and copy operations to the MD PCPU region.
Change sysmap initialization to only allocate KVA pages for CPUs that
are actually present.
While here, collapse CMAP3 into CMAP2 (their use was mutually exclusive
anyway) and "recover" some space in PCPU padding that has always been
available due to 64-byte cacheline padding.
Reviewed by: skra
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D9172
descriptor state will not change anymore). This seems to eliminate the
race where we can miss a stalled queue under high load.
While here remove the unnecessary curly brackets.
Reported by: Konstantin Kormashev <konstantin@netgate.com>
MFC after: 3 days
Sponsored by: Rubicon Communications, LLC (Netgate)
- Pad small packets to 60 bytes and not 64 (exclude the CRC bytes);
- Pad the packet using m_append(9), if the packet has enough space for
padding, which is usually true, it will not be necessary append a newly
allocated mbuf to the chain.
Suggested by: yongari
MFC after: 3 days
Sponsored by: Rubicon Communications, LLC (Netgate)
disabled (Hi netmap!).
Only remove the CRC bytes from packets when the hardware tell us to do so.
Fixes the 'discard frame w/o leading ethernet header' issues.
Sponsored by: Rubicon Communications, LLC (Netgate)
The Zedboard has a hardware bug where initialization of the USB PHY
occasionally fails on boot-up. Fix regression in -CURRENT when
kernel panics on such occasion. 11-RELEASE branch works fine
PR: 215862
Submitted by: Thomas Skibo <thoma555-bsd@yahoo.com>
it into pmap-v4.h where they are used. Other than those few lines of
support for different MMU types, nothing in cpuconf.h has been used in our
code for quite a while.
The file existed to set up a variety of symbols to describe the
architecture. Over the past few years we have converted all of our source
to use the new architecture symbols standardized by ARM Inc, and predefined
by both clang and gcc.
PR: 216104
Replace archaic "busses" with modern form "buses."
Intentionally excluded:
* Old/random drivers I didn't recognize
* Old hardware in general
* Use of "busses" in code as identifiers
No functional change.
http://grammarist.com/spelling/buses-busses/
PR: 216099
Reported by: bltsrc at mail.ru
Sponsored by: Dell EMC Isilon
Add basic support for A33/R16 that is enough to boot a kernel.
This adds the platform code, padconf data and the new clocks strings.
MFC after: 2 weeks
QEMU does not implement hardware debug registers so when
dbg_monitor_is_enabled is called kernel receives "invalid instruction"
exception. QEMU implements only DIDR register and on read returns all
zeroes to indicate that it doesn't support other registers. Real
hardware has Version bits set.
MFC after: 1 week
Rework general approach to locking and working with audio worker thread:
- Use flags to signal requested worker action
- Fix submitted buffer calculations to avoid samples starvation
- Protect buffer pointers with locks to fix race condition between callback
and audio worker thread
- Remove unnecessary vchi_service_use
- Do not use lock to serialize VCHI requests since only one thread issues them now
- Fix unloading signaling per hselasky@ suggestion
- Add output to detect inconsistent callback data caused by possible firmware bug
https://github.com/raspberrypi/firmware/issues/696
- Add stats/debug sysctls to troubleshoot possible bugs
PR: 213687, 205979, 215194
MFC after: 1 week
and host1x module. Unfortunately, tegra124 SoC doesn't have 2D acceleration
engine and 3D requires not yet started nouveau driver.
These drivers forms a first non-x86 DRM2 enabled graphic stack.
Note, there are 2 outstanding issues:
- The code uses gross hack in order to be comply with
OBJT_MGTDEVICE pager. (See tegra_bo_init_pager() in tegra_bo.c)
- Due to improper(probably) refcounting in drm_gem_mmap_single()
(in drm_gem.c), the gem objects are never released.
I hope that I will be able to address both issues in finite time,
but I don't want to touch x86 world now.
MFC after: 1 month
- Place const modifiers where required
- Make sure sdma device is attahched before consumers like SSI
Reviewed by: br
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D8874
file and add a generic DT binding that takes advantage of the extres
framework for setting up clocks.
Reviewed by: gonzo
Differential Revision: https://reviews.freebsd.org/D8826
As cs is stored in a uint32_t, use the last bit to store the
active high flag as it's unlikely that we will have that much CS.
Reviewed by: loos
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D8614
In case where GICD_CTLR.DS is 1, the IGROUPR registers are RW in
non-secure state and has to be initialized to 1 for the
corresponding interrupts to be delivered as Group 1 interrupts.
Update gic_v3_dist_init() and gic_v3_redist_init() to initialize
GICD_IGROUPRn and GICR_IGROUPRn respectively to address this. The
registers can be set unconditionally since the writes are ignored
in non-secure state when GICD_CTLR.DS is 0.
This fixes the hang on boot seen when running qemu-system-aarch64
with machine virt,gic-version=3
Replace them with a default handler that returns devmap_lastaddr.
Reviewed by: mmel
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D8806
Up until r295436 GPT timer in i.MX6 Dual dts used the same compatiblity
string as i.MX6 Quad. After the sync up with Linux in r295436, GPT timer
stopped getting attached on the i.MX6 Dual
MFC after: 3 days
