o rename the new variables to comply with the naming scheme
o move the new variables to an AR5212 specific struct
o use ahp when available
o revert to previous ts_flags check
- remove unused and commented code (MIPS_BUS_SPACE_PCI, pic_usb_ack)
- use rmi_pci_bus_space for USB too (needs byteswap)
- uncomment xls_ehci.c in files.xlr
- changes to xls_ehci.c - updated with dev/usb/controller/ehci_*.c as
Obtained from: JC - c.jayachandran@gmail.com
Enhanced process coredump routines.
This brings in the following features:
1) Limit number of cores per process via the %I coredump formatter.
Example:
if corefilename is set to %N.%I.core AND num_cores = 3, then
if a process "rpd" cores, then the corefile will be named
"rpd.0.core", however if it cores again, then the kernel will
generate "rpd.1.core" until we hit the limit of "num_cores".
this is useful to get several corefiles, but also prevent filling
the machine with corefiles.
2) Encode machine hostname in core dump name via %H.
3) Compress coredumps, useful for embedded platforms with limited space.
A sysctl kern.compress_user_cores is made available if turned on.
To enable compressed coredumps, the following config options need to be set:
options COMPRESS_USER_CORES
device zlib # brings in the zlib requirements.
device gzio # brings in the kernel vnode gzip output module.
4) Eventhandlers are fired to indicate coredumps in progress.
5) The imgact sv_coredump routine has grown a flag to pass in more
state, currently this is used only for passing a flag down to compress
the coredump or not.
Note that the gzio facility can be used for generic output of gzip'd
streams via vnodes.
Obtained from: Juniper Networks
Reviewed by: kan
does not generate excessive interrupts any more so we don't need
to have two copies of interrupt handler.
While I'm here remove two STAT_PUT_IDX register accesses in LE
status event handler. After r204539 msk(4) always sync status LEs
so there is no need to resort to reading STAT_PUT_IDX register to
know the end of status LE processing. Just trust status LE's
ownership bit.
countdown timer register. The timer resolution may vary among
controllers but the value would be represented by core clock
cycles. msk(4) will automatically computes number of required clock
cycles from given micro-seconds unit.
The default interrupt holdoff timer value is 100us which will
ensure less than 10k interrupts under load. The timer value can be
changed with dev.mskc.0.int_holdoff sysctl node.
Note, the interrupt moderation is shared resource on dual-port
controllers so you can't use separate interrupt moderation value
for each port. This means we can't stop interrupt moderation in
driver stop routine. Also have msk_tick() reclaim transmitted Tx
buffers as safety belt. With this change there is no need to check
missing Tx completion interrupt in watchdog handler, so remove it.
full-duplex. Previously msk(4) used to allow flow-control on
1000baseT half-duplex media. Also GMAC pause is enabled if link
partner is capable of handling it.
While I'm here use IFM_OPTIONS instead of using IFM_GMASK to check
optional flags of link.
query routines. This code is necessarily more fragile in the presence of
kernel changes than querying the kernel via sysctl (the default), but
useful when investigating crashes or live kernel state via firewire.
MFC after: 1 week
Sponsored by: Juniper Networks
- Rename the netisr protocol registration array, 'np' to 'netisr_proto',
in order to reduce the chances of symbol name collisions. It remains
statically defined, but it will be looked up by netstat(1).
- Move certain internal structure definitions from netisr.c to
netisr_internal.h so that netstat(1) can find them. They remain
private, and should not be used for any other purpose (for example,
they should not be used by kernel modules, which must instead use the
public interfaces in netisr.h).
- Store a kernel-compiled version of NETISR_MAXPROT in the global variable
netisr_maxprot, and export via a sysctl, so that it is available for use
by netstat(1). This is especially important for crashdump
interpretation, where the size of the workstream structure is determined
by the maximum number of protocols compiled into the kernel.
MFC after: 1 week
Sponsored by: Juniper Networks
(DPCPU):
A new API, kvm_dpcpu_setcpu(3), selects the active CPU for the purposes
of DPCPU. Calls to kvm_nlist(3) will automatically translate DPCPU
symbols and return a pointer to the current CPU's version of the data.
Consumers needing to read the same symbol on several CPUs will invoke a
series of setcpu/nlist calls, one per CPU of interest.
This addition makes it possible for tools like netstat(1) to query the
values of DPCPU variables during crashdump analysis, and is based on
similar code handling virtualized global variables.
MFC after: 1 week
Sponsored by: Juniper Networks, Inc.
This is a split merge because of non-uniform licensing of the DTC package
contents and the way these components will be used in the FreeBSD environment.
The original DTC package is composed of the following two major pieces:
1. sys/contrib/libfdt (BSD [dual] license)
2. contrib/dtc (GPLv2)
The libfdt component is going to be shared in all aspects of the environment:
- /boot/loader
- kernel
- dtc (the device tree compiler proper, userspace tool)
msdosfs-specific variant of vn_vget_ino(), msdosfs_deget_dotdot().
As was done for UFS, relookup the dotdot denode after the call to
msdosfs_deget_dotdot(), because vnode lock is dropped and directory
might be moved.
Tested by: pho
MFC after: 3 weeks
