ATA specification declares minimal reset time of 5us. SATA keeps it, but
requires devices to handle commands transmitted even one by one without
any gap.
as ATA RAID, but generic ATAPCI driver unable to detect drives there. AHCI
driver reported to handle them fine. Linux does the same.
Submitted by: Andrey V. Elsukov on stable@
ata_detach() to implement IOCATAATTACH/IOCATADETACH ioctls.
This will permit channel drivers to properly shutdown port hardware on channel
detach and init it on attach.
join allocate() and dmainit() atapci subdriver's channel initialization
methods into single ch_attach() method.
As opposite to ch_attach() add new ch_detach() method to deallocate/disable
channel.
to not allocate them after the recent ata channels enumeration changes.
It allows to save some resources, not bother user with unexisting hardware
and not check unimplemented ports status on every interrupt.
Works fine with AHCI and theoretically other MSI capable devices.
At this moment support disabled by default. To enable it, set
"hint.atapci.X.msi=1" device hint.
- specification claims that 1 second is just a maximum controller reset time;
implement controller reset properly to save almost 1 second of boot, and
about half second of resume time;
- enable channel interrupts only after channel status reset to fix duplicate
device creation on resume due to unwanted device connection event;
- as described in specification, wait for disk ready status after channel
power-up; it is not so important when disk already touched by BIOS, but
solves device not ready problems on resume and probably some other cases.
- uncomment channel stop/start on soft-reset as it is declared mandatory by
specification; it was commented due to some random drive detection problems
on VIA and JMicron controllers, but I hope it is fixed by previous point.
Move channel softc initialization from ata_XXX_probe() to ata_XXX_attach().
Instead of calculating ata channel number as position in child device list,
pass it's real number directly from controller probe routine using ivars.
It is simpler and IMHO more correct.
expected in acd_fixate().
This should fix various problems folks are having with 'burncd' reporting
"burncd: ioctl(CDRIOCFIXATE): Input/output error" during the fixate phase
when "fixate" is issued together with the "data" command.
PR: 95979
Submitted by: Jaakko Heinonen <jh@saunalahti.fi>
created by atapicam is being kept opened or mounted. This is probably just
a temporary solution until we invent something better.
Reviewed by: scottl
Approved by: rwatson (mentor)
Sponsored by: FreeBSD Foundation
Reported by: Jaakko Heinonen
storage class. This check was lost. It is not important for the most cases,
but as it was reported on current@, it does important for sis driver and
surely inportant for AHCI driver. So restore it there.
Submitted by: Toshikazu ICHINOSEKI, Andrey V. Elsukov
Discussed on: current@
configuration registers (which are not going to change) on every interrupt
looks expensive, especially when interrupt is shared. Profiling shows me 3%
of time spent by atapci0 on pure network load due to IRQ sharing with em0.
(still a power of 2) rather than 63k transfers. Even with 63k transfers
some machines (such as Dell SC1435's) were experiencing chronic data
corruption.
- Use the MIO method to talk to the Serverworks HT1000_S1 SATA controller
like all the other SATA controllers rather than the compat PATA
method. This lets the controller see all 4 SATA ports and also
matches the behavior of the Linux driver.
Silence from: sos
MFC after: 3 days
If you just config KERNEL as usual there should be no apparent changes, you'll get all chipset support code compiled in.
However there is now a way to only compile in code for chipsets needed on a pr vendor basis. ATA now has the following "device" entries:
atacore: ATA core functionality, always needed for any ATA setup
atacard: CARDBUS support
atacbus: PC98 cbus support
ataisa: ISA bus support
atapci: PCI bus support only generic chipset support.
ataahci: AHCI support, also pulled in by some vendor modules.
ataacard, ataacerlabs, ataadaptec, ataamd, ataati, atacenatek, atacypress, atacyrix, atahighpoint, ataintel, ataite, atajmicron, atamarvell, atamicron, atanational, atanetcell, atanvidia, atapromise, ataserverworks, atasiliconimage, atasis, atavia; Vendor support, ie atavia for VIA chipsets
atadisk: ATA disk driver
ataraid: ATA softraid driver
atapicd: ATAPI cd/dvd driver
atapifd: ATAPI floppy/flashdisk driver
atapist: ATAPI tape driver
atausb: ATA<>USB bridge
atapicam: ATA<>CAM bridge
This makes it possible to config a kernel with just VIA chipset support by having the following ATA lines in the kernel config file:
device atacore
device atapci
device atavia
And then you need the atadisk, atapicd etc lines in there just as usual.
If you use ATA as modules loaded at boot there is few changes except the rename of the "ata" module to "atacore", things looks just as usual.
However under atapci you now have a whole bunch of vendor specific drivers, that you can kldload individually depending on you needs. Drivers have the same names as used in the kernel config explained above.
After I removed all the unit2minor()/minor2unit() calls from the kernel
yesterday, I realised calling minor() everywhere is quite confusing.
Character devices now only have the ability to store a unit number, not
a minor number. Remove the confusion by using dev2unit() everywhere.
This commit could also be considered as a bug fix. A lot of drivers call
minor(), while they should actually be calling dev2unit(). In -CURRENT
this isn't a problem, but it turns out we never had any problem reports
related to that issue in the past. I suspect not many people connect
more than 256 pieces of the same hardware.
Reviewed by: kib
Thanks goes to ITE who provided docs and feedback and made this possible.
Minor fixups to the Intel ICH code for bugs found while doing this.
(ITE8213 is very semilar to an Intel ICH)
MFC after: 1 week
This can be used to disable the 80pin cable check on systems which forget to
set the bit -- such as certain laptops and Soekris boards.
PR: kern/114605 (somewhat reworked)
Submitted by: marck
MFC after: 1 week
when it worked as generic IDE.
PR: 125422
Submitted by: Andrey V. Elsukov <bu7cher at yandex dot ru>
Approved by: imp (mentor, implicit)
MFC after: 1 week
