Return failure, if the enable bit corresponding to the map type has not
been set in the command register. This feature was requested by Justin
Gibbs, who pointed out that some early PCI to PCI bridges do not correctly
support memory windows (I assume because of the risk of deadlocks that
have been taken care of in the PCI 2.2 spec) and that some BIOS clears
the memory address decode enable bit in the command register of the PCI
device, if it finds them behind such a bridge.
1) Stop at the first map register that contains a zero value.
2) When testing for the map size work up from low values, since
this works around a bug in some BusLogic SCSI card, which has
the 16 upper port base address bits hardwired to zero.
The config register dump printed in the bootverbose case has
been slightly rearranged.
Adjust the data port address by adding the two low order bits of
the register number. The address port takes only a word address
(i.e. ignores the two low order bits written to it).
mode 1. Omission of this bit makes all config register accesses fail in
on recent chip sets ...
(The problem was reported and debug output provided by: Steve Passe)
- vector.s <- stub called by i386/exception.s
- icu_vector.s <- UP
- apic_vector.s <- SMP
Split icu.s into UP and SMP specific files:
- ipl.s <- stub called by i386/exception.s (formerly icu.s)
- icu_ipl.s <- UP
- apic_ipl.s <- SMP
This was done in preparation for massive changes to the SMP INTerrupt
mechanisms. More fine tuning, such as merging ipl.s into exception.s,
may be appropriate.
reality. There will be a new call interface, but for now the file
pci_compat.c (which is to be deleted, after all drivers are converted)
provides an emulation of the old PCI bus driver functions. The only
change that might be visible to drivers is, that the type pcici_t
(which had been meant to be just a handle, whose exact definition
should not be relied on), has been converted into a pcicfgregs* .
The Tekram AMD SCSI driver bogusly relied on the definition of pcici_t
and has been converted to just call the PCI drivers functions to access
configuration space register, instead of inventing its own ...
This code is by no means complete, but assumed to be fully operational,
and brings the official code base more in line with my development code.
A new generic device descriptor data type has to be agreed on. The PCI
code will then use that data type to provide new functionality:
1) userconfig support
2) "wired" PCI devices
3) conflicts checking against ISA/EISA
4) maps will depend on the command register enable bits
5) PCI to Anything bridges can be defined as devices,
and are probed like any "standard" PCI device.
The following features are currently missing, but will be added back,
soon:
1) unknown device probe message
2) suppression of "mirrored" devices caused by ancient, broken chip-sets
This code relies on generic shared interrupt support just commited to
kern_intr.c (plus the modifications of isa.c and isa_device.h).
be (eventually) architecture independent. It provides an emulation
of the ISA interrupt registration function register_intr(), but that
function does no longer manipulated the interrupt controller and
interrupt descriptor table, but calls the architecture dependent
function setup_icu() for that purpose.
After the ISA/EISA bus code has been modified to directly call the new
interrupt registartion functions (intr_create() and intr_connect()),
the emulation of register_intr() should be dropped.
The C level interrupt handler function should take a (void*) argument,
and the function pointer type (inthand2_t) should defined in some other
place than isa_device.h.
This commit is a pre-requisite for the removal of the PCI specific shared
interrupt code.
Reviewed by: dfr,bde
be (eventually) architecture independent. It provides an emulation
of the ISA interrupt registration function register_intr(), but that
function does no longer manipulated the interrupt controller and
interrupt descriptor table, but calls the architecture dependent
function setup_icu() for that purpose.
After theISA/EISA bus code has been modified to directly call the new
interrupt registartion functions (intr_create() and intr_connect()),
the emulation of register_intr() should be dropped.
The C level interrupt handler function should take a (void*) argument,
and the function pointer type (inthand2_t) should defined in some other
place than isa_device.h.
This commit is a pre-requisite for the removal of the PCI specific shared
interrupt code.
Reviewed by: dfr,bde
This is now the default, it delays most of the MP startup to the function
machdep.c:cpu_startup(). It should be possible to move the 2 functions
found there (mp_start() & mp_announce()) even further down the path once
we know exactly where that should be...
Help from: Peter Wemm <peter@spinner.dialix.com.au>
- The 1st (preparse_mp_table()) counts the number of cpus, busses, etc. and
records the LOCAL and IO APIC addresses.
- The 2nd pass (parse_mp_table()) does the actual parsing of info and recording
into the incore MP table.
This will allow us to defer the 2nd pass untill malloc() & private pages
are available (but thats for another day!).
When a panic occurs early in the SMP boot process 'cpunumber()' hangs,
causing the panic string to be lost. Now the system appears to hang
in 'breakpoint()', but at least the user sees the panic string before the
hang.
switch. I needed 'LINT' to compile for other reasons so I kinda got the
blood on my hands. Note: I don't know how to test this, I don't know if
it works correctly.
Don't search for interface addresses matching interface "NULL"
it's likely to cause a page fault..
this can be triggered by the ipfw code rejecting a locally generated
packet (e.g. you decide to make some network unreachable by local users)
ppp (or will be shortly). Natd can now be updated to use
this library rather than carrying its own version of the code.
Submitted by: Charles Mott <cmott@srv.net>
panic( "xxxxx\n" );
to:
printf( "xxxxx\n" );
panic( "\n" );
For some as yet undetermined reason the argument to panic() is often NOT
printed, and the system sometimes hangs before reaching the panic printout.
So we hopefully at least print some useful info before the hang, as oppossed to
leaving the user clueless as to what has happened.
bytes. Move p_hash to where it should have been all along, since we
change the layout anyway.
Recompile ps, top, libutil and all that.
Taked about with: bde
Remove "setdefs.h" and arrange to generate it automatically at
ELF kernel build time.
"gensetdefs.c" is a utility which scans a set of ELF object files
and outputs a line ``DEFINE_SET(name, length);'' for each linker
set that it finds. When generating an ELF kernel, this is run just
before the final link to generate "setdefs.h".
Remove the init_sets() function from "setdef0.c", and its call from
"machdep.c". Since "gensetdefs.c" calculates the length of each
set, it is no longer necessary in an ELF kernel to count the set
elements at kernel initialization time. Also remove "set_of_sets"
which was used for this purpose.
Link "setdef0" and "setdef1" into the kernel only if building for
ELF. Since init_sets() is no longer used, there is no need to link
them into an a.out kernel.
all uses of it with the equivalent calls to setbits().
This change incidentally eliminates a problem building ELF kernels
that was caused by SETBITS.
Reviewed by: fsmp, peter
Submitted by: bde
PR: kern/3629: /sys/scsi/pt.c doesn't...
Submitted by: simokawa@sat.t.u-tokyo.ac.jp (Hidetoshi Shimokawa)
Add a catch-all record for removable SCSI devices to default them to
only one LUN.
PR: kern/3580: Bad LUN probes on Xyratex...
1) Adjust NFRAMES from 16 to 8 per 16k of memory.
2) Acknowledge interrupts to the card early in the interrupt
handler before processing the event that caused the interrupt.
This frees the card to process addtional events instead of
waiting for the driver to finish handling events.
3) Changed the initialization of the transmit buffers to be a
loop so that the number of buffers can be more easily changed.
4) Moved the code to take the adapter out of loop back mode to just
before we enable the receiver.
I also made the driver dynamically size its resource arrays at attach
time so that we can take full advantage of adapters with more than 16k
of memory.
Richard has some other changes he's working on to improve performance,
but this should get ee16 support working reliably again.
Thanks to Wes Santee <wes@bogon.net> for testing these patches.
Submitted by: Richard Straka <straka@user1.inficad.com>
the man page or the source file. Fix this.
Minor problem: don't choke with ENETDOWN early. As long as our output
queue has space, put the IP packets there even if IPCP ain't up yet.
We will eventually be able delivering them once the PPP state machine
came up.
full implementation of the sate machine as described in RFC1661, and
provides support for plugging in various control protocols. I needed
this to provide PPP support for the BISDN project (right now).
Unfortunatley, while the existing API was almost up to the point, i
needed one minor API change in order to decouple the this-layer-
started and this-layer-finished actions from the respective Up and
Down events of the lower layer. This requires two additional lines in
the attach routines of all existing lower layer interface drivers that
are using syncPPP (shortcutting these actions and events). Apart from
this, i believe i didn't change the API of all this, so everything
should plug in without too many hassles. Please report if i broke
something in the existing drivers.
For a list of features (including new ones like dial-on-demand), and
things still to be done, please refer to the man page i'll commit asap.
Encouraged by: Serge Vakulenko <vak@cronyx.ru>
- remove all calls to scsi_stop_unit(). Some drives refuse commands when
stopped. This will fix the 'device not configured' message which was
cleared after opening/closing the tray.
- Never set the logical block address in the scsi_cmd struct when writing.
The computation was bogus for block sizes not a multiple of DEV_BSIZE.
(the bug is still there in the READ case)
- reset the block size to the 2048 bytes in finalize_track() track to avoid
an error when mounting a disk after an audio write.
- remove the WORMIOCQUIRKSELECT ioctl. Quirks are now recorded at probe time
(see scsiconf.c)
- change and expand the argument to the WORMIOCPREPTRACK ioctl. It now possible
to select more track options (copy bits, ISRC codes, track type,
track number)
- add an error handler to catch false errors (warnings in fact) and record
the error type.
- add an ioctl call (WORMIOERROR) to get more information on the nature of the
error when a command or a write failed.
- add an ioctl call (WORMIOCFINISHTRACK) to finalize a track without closing
the device (closing the device still finalize the track if the command was
not performed)
Approved by: joerg
and b_validend. The changes to vfs_bio.c are a bit ugly but hopefully
can be tidied up later by a slight redesign.
PR: kern/2573, kern/2754, kern/3046 (possibly)
Reviewed by: dyson
in_setsockaddr and in_setpeeraddr.
Handle the case where the socket was disconnected before the network
interrupts were disabled.
Reviewed by: Garrett Wollman <wollman@khavrinen.lcs.mit.edu>
- gcc assumes that %ecx and %edx are clobbered (due to calling
conventions), thus there is no need for saving/restoring those two
registers.
- %es is reset to default value by real_to_prot, thus there is no need
for saving/restorig that register.
Submitted by: tegge
When an ioctl command SW_XXXX is issued, scioctl() checks if the font
appropriate for the specified mode is already loaded. The check was
correctly done for 8 line and 16 line fonts, but not for 14 line font.
The symbols FONT_8, FONT_14 and FONT_16 were defined as numbers but
were sometimes treated as bit flags. They are now defined as bit
flags.
2) screen blinking (two fixes)
Removed a redundant call to timeout() in do_bell().
Don't let blink_screen() write to the video buffer if the screen is in
the graphics (UNKNOWN) mode.
3) screen saver timeout
The ioctl command CONS_BLANKTIME sets the screen saver's timeout. The
value of zero will disable the screen saver. If the screen saver is
currently running it should be stopped.
4) border color and destructive cursor (two fixes)
The border color and the cursor type can be changed via escape
sequences. But only VGA can change the border color and set the
cursor type to destructive (CHAR_CURSOR) in the current syscons.
scan_esc() failed to check this.
Reviewed by: sos
- TFTP is not needed any longer.
Add some other improvements:
- swapsize is now detected if no value was specified.
- resvport is used by default
- merged code for setting/showing mount options for root/swap.
Submitted by: Luigi Rizzo <luigi@labinfo.iet.unipi.it>
conflict with the kernel visible one. Make the new stuff not visible if
_ANSI_SOURCE or _POSIX_SOURCE is defined (!) because the new things are
not part of the base 1003.1-1990 standard or ansi (says Bruce).
Reviewed by: bde
compatible with boot proms made from the 2.2 source.
Convert the nfs arguments when copying to the new diskless structure.
Copy the gateway field in the diskless structure.
- merged SMP option SMP_AUTOSTART from LINT
- enabled SMP_AUTOSTART, since it's the desired working mode and it's
reported to work now.
PR:
Reviewed by:
Submitted by:
Obtained from:
to fill in the nfs_diskless structure, at the cost of some kernel
bloat. The advantage is that this code works on a wider range of
network adapters than netboot. Several new kernel options are
documented in LINT.
Obtained from: parts of the code comes from NetBSD.
was stale.
Fixed initialization of gdt[] for the BDE_DEBUGGER case. APM entries
clobbered debugger entries if the debugger was loaded (APM is incompatible
with BDE_DEBUGGER) and unused entries were garbage if the debugger wasn't
loaded.
printf(9), so the log output doesn't clutter the console.
While i was at it, KNFified some function definitions. This file was
very inconsistent in this respect.
Serious:
- An important timevalfix() in settime[ofday]() was lost.
Not so serious:
- There was a race initializing `delta' in the check for setting the
time backwards.
- The `#ifdef notyet' check for setting the time more than a day forwards
was back to front.
[[I deleted the code, it's useless because of iteration - Peter]]
- The timespec was not checked for validity in clock_settime().
- The timespec was not fully checked for validity in nanotime(). The
check in itimerfix() is too late, since the conversion from a timespec
to a timeval may overflow.
- A garbage timeval was checked in settimeofday() for the (uap->tv == NULL
&& uap->tzp != NULL) case. I added the broken check this some time ago.
Cosmetic:
- The "inadvertantly (sic) sleeping forever" test always failed. hzto()
always returns >= 1.
- The style wasn't very KNFish. (I only changed new code.)
Submitted by: bde
and not the MAC address of the first interface for every IPX address.
This is more inline with the way others like Novell do it.
Originally Submitted by: "Serge A. Babkin" <babkin@hq.icb.chel.su>
Use the MAC address of an interface for the host part of an IPX address
and not the MAC address of the first interface for every IPX address.
This is more inline with the way others like Novell do it.
Mostly Submitted by: "Serge A. Babkin" <babkin@hq.icb.chel.su>
Take out the error messages (the ip icmp equivalent) with #ifdef IPXERRORMSGS.
This is bogus and as far as I could figure out IPX don't have anything like
it. This is a leftover from its XNS heritage. If nobody complains, I will
take it out completely in a few weeks.
Add some more ipxstat statistics counters.
Make ipxprintfs a sysctl variable and off by default.
Add IPX Netbios "routing" support. This is off by default and can be
switched on with a sysctl knob.
General code cleanup to at least use the same style throughout the IPX
code, but also be more style(9) conformant. Also make a lot of functions
static.
If I don't get any complaints I'll bring all of this over to the 2.2 tree
in a few weeks.
accessing files which it shouldn't be able to. This required a better
approximation of VOP_ACCESS for NFSv2 (NFSv3 already has an ACCESS rpc
which is a better solution) and adding a call to VOP_ACCESS from VOP_LOOKUP.
PR: kern/876, kern/2635
Submitted by: David Malone <dwmalone@maths.tcd.ie> (for kern/2635)
in NetBSD. The core of settimeofday() is moved to a seperate static
function settime() which both clock_settime() and settimeofday() call.
Note that I picked up the securelevel > 1 check from NetBSD that prevents
the clock being set backwards in high securelevel mode (this was a hole
that allowed resetting of inode access timestamps to arbitary values)
Obtained from: mostly from NetBSD, but the settime() function is from
our gettimeofday(), some tweaks by me.
(eg: above 0xffc00000). Programs using /dev/kmem are implicitly racing
the kernel, and can get right up high in memory. I've been running
these for some time now, but with printfs. It's saved two panics at
least that I can remember.
md_regs being struct trapframe *. Do a npxsave() if needed and copy the
pcb rather than use the increasingly defunct savectx(). Copy %edi and
%ebp explicitly.
Submitted by: bde
XXX npxproc could be declared in npx.h so the externs with smp fruit
are not needed.
Remove TF_REGP() macro and use. The original reason (address space
problems due to having UPAGES in mapped into user space) is gone. It
looks cleaner without it.
the patches in freefall:/home/dfr/ld.diffs to your ld sources and set
BINFORMAT to aoutkld when linking the kernel.
Library changes and userland utilities will appear in a later commit.
- doesn't break my system.
- NOT yet verified on the affected motherboard.
Stifle an annoying dma_start busy message for the sound cards.
Submitted by: "John S. Dyson" <toor@dyson.iquest.net>
the work is silly, and all this will be a moot point with Justin's CAM
driver, and there are still many ioctls missing -- but i need these
right now. It's silly to need to move the CD-R back to the other
drive in order to determine the session start info when burning multi-
session CD-Rs.
. It makes cd9660 root f/s working again.
. It makes CD9660 a new-style option.
. It adds support to mount an ISO9660 multi-session CD-ROM as the root
filesystem (the last session actually, but that's what is expected
behaviour).
Sigh. The CDIOREADTOCENTRYS did a copyout() of its own, and thus has
been unusable for me for this work. Too bad it didn't simply stuff
the max 100 entries into the struct ioc_read_toc_entry, but relied on
a user supplied data buffer instead. :-( I now had to reinvent the
wheel, and created a CDIOREADTOCENTRY ioctl command that can be used
in a kernel context.
While doing this, i noticed the following bogosities in existing CD-ROM
drivers:
wcd: This driver is likely to be totally bogus when someone tries
two succeeding CDIOREADTOCENTRYS (or now CDIOREADTOCENTRY)
commands with requesting MSF format, since it apparently
operates on an internal table.
scd: This driver apparently returns just a single TOC entry only for
the CDIOREADTOCENTRYS command.
I have only been able to test the CDIOREADTOCENTRY command with the
cd(4) driver. I hereby request the respective maintainers of the
other CD-ROM drivers to verify my code for their driver. When it
comes to merging this CD-ROM multisession stuff into RELENG_2_2 i will
only consider drivers where i've got a confirmation that it actually
works.
simplifies some assumptions and stops some code compile problems.
This should fix the compile hiccup in PR#3491, but smp kernel profiling
isn't likely to be fixed by this.
".." vnode. This is cheaper storagewise than keeping it in the
namecache, and it makes more sense since it's a 1:1 mapping.
2. Also handle the case of "." more intelligently rather than stuff
the namecache with pointless entries.
3. Add two lists to the vnode and hang namecache entries which go from
or to this vnode. When cleaning a vnode, delete all namecache
entries it invalidates.
4. Never reuse namecache enties, malloc new ones when we need it, free
old ones when they die. No longer a hard limit on how many we can
have.
5. Remove the upper limit on namelength of namecache entries.
6. Make a global list for negative namecache entries, limit their number
to a sysctl'able (debug.ncnegfactor) fraction of the total namecache.
Currently the default fraction is 1/16th. (Suggestions for better
default wanted!)
7. Assign v_id correctly in the face of 32bit rollover.
8. Remove the LRU list for namecache entries, not needed. Remove the
#ifdef NCH_STATISTICS stuff, it's not needed either.
9. Use the vnode freelist as a true LRU list, also for namecache accesses.
10. Reuse vnodes more aggresively but also more selectively, if we can't
reuse, malloc a new one. There is no longer a hard limit on their
number, they grow to the point where we don't reuse potentially
usable vnodes. A vnode will not get recycled if still has pages in
core or if it is the source of namecache entries (Yes, this does
indeed work :-) "." and ".." are not namecache entries any longer...)
11. Do not overload the v_id field in namecache entries with whiteout
information, use a char sized flags field instead, so we can get
rid of the vpid and v_id fields from the namecache struct. Since
we're linked to the vnodes and purged when they're cleaned, we don't
have to check the v_id any more.
12. NFS knew about the limitation on name length in the namecache, it
shouldn't and doesn't now.
Bugs:
The namecache statistics no longer includes the hits for ".."
and "." hits.
Performance impact:
Generally in the +/- 0.5% for "normal" workstations, but
I hope this will allow the system to be selftuning over a
bigger range of "special" applications. The case where
RAM is available but unused for cache because we don't have
any vnodes should be gone.
Future work:
Straighten out the namecache statistics.
"desiredvnodes" is still used to (bogusly ?) size hash
tables in the filesystems.
I have still to find a way to safely free unused vnodes
back so their number can shrink when not needed.
There is a few uses of the v_id field left in the filesystems,
scheduled for demolition at a later time.
Maybe a one slot cache for unused namecache entries should
be implemented to decrease the malloc/free frequency.
in savedvp variable and it is used for the argument of
MOUNTTOUNIONMOUNT(). I didn't realize ap->a_vp is modified before
MOUNTTOUNIONMOUNT(), so the change by revision 1.22 is incorrect.
- one-liners all become inline.
- multi-liners become functions.
- FAST_IPI defines go away.
re-worked APICIPI_BANDAID code.
- now refered to as DETECT_DEADLOCK.
- on by default.
the pageout daemon wasn't always being waken up appropriately when the
(cache + free) queues were depleted.
Submitted by: David S. Miller <davem@jenolan.rutgers.edu>
but now that we've widened the scope of the smp work to -current, it might
be an idea to warn new people that might not have read all the docs yet
that the SMP support needs to be activated via a sysctl.
Added [SR]RGBMASKs ioctl for byte swapping.
1.16 4/20/97 Randall Hopper <rhh@ct.picker.com>
Generalized RGBMASK ioctls for general pixel
format setting [SG]ACTPIXFMT, and added query API
to return driver-supported pix fmts GSUPPIXFMT.
1.17 4/21/97 hasty@rah.star-gate.com
Clipping support added.
1.18 4/23/97 Clean up after failed CAP_SINGLEs where bt
interrupt isn't delivered, and fixed fixing
CAP_SINGLEs that for ODD_ONLY fields.
Submitted by: individuals in above log messages.
Added [SR]RGBMASKs ioctl for byte swapping.
1.16 4/20/97 Randall Hopper <rhh@ct.picker.com>
Generalized RGBMASK ioctls for general pixel
format setting [SG]ACTPIXFMT, and added query API
to return driver-supported pix fmts GSUPPIXFMT.
1.17 4/21/97 hasty@rah.star-gate.com
Clipping support added.
1.18 4/23/97 Clean up after failed CAP_SINGLEs where bt
interrupt isn't delivered, and fixed fixing
CAP_SINGLEs that for ODD_ONLY fields.
Submitted by: individuals in above log messages.
opt_smp_invltlb.h
from:
SMPHDRS= opt_smp.h opt_smp_invltlb.h
SMP_INVLTLB is no longer a valid config option, the invalidation of the TLB
via inter-CPU IPIs is now standard when APIC_IO is used.
This code re-numbers PCI busses in the MP table to match PCI semantics
when the MP BIOS fails to do it properly.
Reviewed by: Peter Wemm <peter@spinner.DIALix.COM>
but searching the directory on something else than the default
location.
NB: this comprises an interface change to the mount_cd9660(8)
utility (commit will follow). You need to rebuild both.
I've got similar patches for RELENG_2_2, should i commit them too?
and FNM_LEADING_DIR were specified and the pattern ended with "*".
Example: pattern="src/usr.sbin/w*", string="src/usr.sbin/watch/watch.8,v".
This should match, but did not.
UN_KLOCK flag.
When UN_KLOCK is set, VOP_UNLOCK should keep uppervp locked and clear
UN_ULOCK flag. To do this, when UN_KLOCK is set, (1) union_unlock
clears UN_ULOCK and does not clear UN_KLOCK, (2) union_lock() does not
access uppervp and does not clear UN_KLOCK, and (3) callers of
vput/VOP_UNLOCK should clear UN_KLOCK. For example, vput becomes:
SETKLOCK(union_node);
vput(vnode);
CLEARKLOCK(union_node);
where SETKLOCK macro sets UN_KLOCK and CLEARKLOCK macro clears
UN_KLOCK.
replace invldebug with invltlb_ok for throttling smp_invltlb() during boot.
Reviewed by: informal discussion with Peter Wemm <peter@spinner.DIALix.COM>
make world fails when it tries to build LKMs because the files
opt_smp.h
opt_smp_invltbl.h
are missing.
This patch to /usr/src/share/mk/bsd.kmod.mk is a temporary workaround.
Note that LKMs built in this way may or may NOT work properly with an
SMP kernel.
Peter Wemm <peter@spinner.DIALix.COM>, Steve Passe <smp@csn.net>
removed all the IPI_INTS code.
made the XFAST_IPI32 code default, renaming Xfastipi32 to Xinvltlb.
cleanup of i386/isa/isa_device.h to eliminate SMP dependancies:
made the id_irq member of struct isa_device an u_int.
made the id_drq member of struct isa_device an int.
removed all other '#ifdefs' concerning SMP & APIC_IO.
removed SMP/APIC_IO dependancies from if_ze.c.
Peter Wemm <peter@spinner.DIALix.COM>, Steve Passe <smp@csn.net>
removed all the IPI_INTS code.
made the XFAST_IPI32 code default, renaming Xfastipi32 to Xinvltlb.
source files via a 'cc -include opt_global.h ...' type arrangement.
This means we can untangle certain header files.
options.i386 has a placeholder until it has a real member so we can avoid
having to teach config about it just yet.
Reviewed by: bde
This commit includes the following changes:
1) Old-style (pr_usrreq()) protocols are no longer supported, the compatibility
glue for them is deleted, and the kernel will panic on boot if any are compiled
in.
2) Certain protocol entry points are modified to take a process structure,
so they they can easily tell whether or not it is possible to sleep, and
also to access credentials.
3) SS_PRIV is no more, and with it goes the SO_PRIVSTATE setsockopt()
call. Protocols should use the process pointer they are now passed.
4) The PF_LOCAL and PF_ROUTE families have been updated to use the new
style, as has the `raw' skeleton family.
5) PF_LOCAL sockets now obey the process's umask when creating a socket
in the filesystem.
As a result, LINT is now broken. I'm hoping that some enterprising hacker
with a bit more time will either make the broken bits work (should be
easy for netipx) or dike them out.
1) i586_bcopy() problem
There have been a number of reports that the syscons doesn't work
properly if i586_bcopy() is enabled.
The problem prevented users from installing 2.2(.1)-RELEASE. The
symptom is that the system looks frozen during device probe or just
before the main installation menu. The workaround was to specify the
flag 0x01 to the npx device so that i586_bcopy() is disabled.
The patch forces the syscons to call generic_bcopy() when copying
to/from the video memory, even if CPU is Pentium and i586_bcopy() is
enabled. i586_bcopy() is still called for copy operations between
non-video memory regions.
PR: kern/2277, kern/3066, kern/3107, kern/3134
2) video mode parameter table problem
The syscons reads and uses the video mode parameter table provided by
the VGA BIOS to set VGA registers when changing video mode and
modifying font data. It appears that in some VGA BIOSes the table is
not ordered as the syscons expects, and this leads to screen
corruption.
The problem prevented users from installing 2.2(.1)-RELEASE. The
symptom is the corrupt screen or strange vertical lines soon after the
kernel is loaded into memory (just after the kernel decompression).
The patch performs simplistic test and if it fails, set video_mode_ptr
to NULL so that the video mode switching won't happen.
This is an interim kludge. There should be a better way to deal with
the problem.
PR: kern/2498, conf/2775, conf/3354
Reviewed by: sos
Tested by: PR originators (not all of them, though)
The SMP source was merged into 3.0-current last nite and this broke
the make of sbin/dset.
Should make things work for non-SMP case.
People making SMP kernels will need to edit i386/isa/isa_device.h, re-enabling
'#include "opt_smp.h"'. People making SMP worlds will have to punt for now...
I'm thinking about the real solution, but for now the goal is to NOT break
the world!
There are various options documented in i386/conf/LINT, there is more to
come over the next few days.
The kernel should run pretty much "as before" without the options to
activate SMP mode.
There are a handful of known "loose ends" that need to be fixed, but
have been put off since the SMP kernel is in a moderately good condition
at the moment.
This commit is the result of the tinkering and testing over the last 14
months by many people. A special thanks to Steve Passe for implementing
the APIC code!
When we request sense, don't allow disconnection. This closes a window
where we might allow an overlapped tagged and non-tagged transaction.
The correct fix is to freeze the queue for the target that requests sense
which is what will happen in the new CAM framework.
Our vput calls vm_object_deallocate() --> vm_object_terminate(). The
vm_object_terminate() calls vn_lock(), since UN_LOCKED has been
already cleared in union_unlock(). Then, union_lock locks upper vnode
when UN_ULOCK is not set. The upper vnode is not unlocked when
UN_KLOCK is set in union_unlock(), thus, union_lock tries to lock
locked vnode and we get panic.
if SCB Paging was enabled:
disconnect with more data to transfer
disconnected SCB gets paged out
target reconnects so we page SCB back in
target completes transfer so residual is 0
target disconnects
SCB gets reused but not paged out since the residual is 0 (optimization)
target reconnects so we page the SCB back in
we report a residual because of stale residual information.
The fix for this is to set a flag that forces the SCB to be paged back
up to the host if we page in an SCB with a residual
Pointed out by: Doug Ledford <dledford@dialnet.net>
Fix another bug: if argv[0] is NULL, garbadge args might be added for
shell script
Submitted by: Tor Egge <Tor.Egge@idi.ntnu.no> (with yet one fault detect from me)
for syscalls, so one frame was lost in backtraces from syscalls.
This is handled better in the kernel by using a different mcount
entry point for profiling before the frame pointer is set up.
Expand RCSID().
Use .p2align instead of the ambiguous .align.
Added idempotency ifdef.
Removed unused macros ALTENTRY(), ALTASENTRY(), ASENTRY(), _MID_ENTRY.
Cleaned up formatting.
Reviewed by: jdp reviewed an old version
Obtained from: parts from NetBSD
large enough to contain the ethernet header. There appears to be a
condition where the card can return "0" in some failure cases, and this
causes bad things to happen (a panic).
have successfully built, booted, and run a number of different ELF
kernel configurations, including GENERIC. LINT also builds and
links cleanly, though I have not tried to boot it.
The impact on developers is virtually nil, except for two things.
All linker sets that might possibly be present in the kernel must be
listed in "sys/i386/i386/setdefs.h". And all C symbols that are
also referenced from assembly language code must be listed in
"sys/i386/include/asnames.h". It so happens that failure to do
these things will have no impact on the a.out kernel. But it will
break the build of the ELF kernel.
The ELF bootloader works, but it is not ready to commit quite yet.
UN_ULOCK flag. This shows a locking violation but I couldn't find the
reason UN_ULOCK is not set or upper vnode is not unlocked. I added
the code that detect this case and adjust un_flags. DIAGNOSTIC kernel
doesn't adjust un_flags, but just panic here to help debug by kernel
hackers.
delay after we reset the card to allow the card to come back to life.
It appears the newer card takes longer to reset.
Submitted by: Samuel Lam <skl@ScalableNetwork.com>
type mismatches. There was no problem in practice (at least on 386's).
The timeout args still get bogusly cast from int to `void *' via
caddr_t and back to int.
type mismatches. mcd and scd were/are particularly bogus. They
used a general purpose function taking 2 args for the timeout
function and fudged varargs stuff to supply the second arg for the
timeout case. This broke `cc -mrtd'. Bounce through a timeout
function instead. The timeout arg still gets bogusly cast from
int to `void *' and back.
difference of approx 3mins in make world on my P6!!! This means
that vfork now has full address space sharing, so beware with
sloppy vfork programming. Also, you really do need to apply
the previously committed popen fix in libc.
type mismatches. There was no problem in practice (at least on 386's).
Don't cast NULL in calls to timeout functions. pcvt is fully prototyped
and doesn't support K&R.
Timeout functions take args of type `void *', so use magic numbers of
type `void *' for UPDATE_* to reduce the danger of wrong conversions.
Removed FreeBSD-pre-1.1-related TIMEOUT_FUNC_T macro. It was especially
bogus for the pre-1.1 case.
type mismatches. There was no problem in practice (at least on 386's).
Removed NetBSD-related TIMEOUT macro. NetBSD uses the same BSD4.4Lite
timeout interface as FreeBSD. As a concession to portability, declare
the timeout function without using the FreeBSD timeout_t typedef.
properly. Simply don't use the gcc macros if we're not gcc, and
declare prototypes for the byte-swapping functions in case the
macro versions are not used. The previous fix was wrong and broke
libpcap, which abuses -Dlint.
Don't pollute the namespace if _POSIX_SOURCE is defined. This is
broken - it makes almost everything in <machine/endian.h> inaccessible
if _POSIX_SOURCE is defined, yet <machine/endian.h> is not a POSIX
header. Other systems don't do it any better.
Removed always-false `BYTE_ORDER == BIG_ENDIAN' ifdef.
Obtained from: partly from Lite(2?) and NetBSD
(pt. unused) for TI PCI1130.
2. pccard.c: PCIC_RESUME_RESET is now (also) a sysctl. (Never make it
a #ifdef if it can be made a sysctl!)
3. pcic.c: make getb() and putb() proper member functions of struct
pcic_slot. Add a couple of missing casts.
wind up writing zeros instead of real data when the file is on an NFSv2
mounted directory.
While tracking this bug down, I noticed that nfs_asyncio was waking *all*
the iods when a block was written instead of just one per block. Fixing this
gives a 25% performance improvment for writes on v2 (less for v3).
Both are 2.2 candidates.
PR: kern/2774
# mount -t union (or null) dir1 dir2
# mount -t union (or null) dir2 dir1
The function namei in union_mount calls union_root. The upper vnode
has been already locked and vn_lock in union_root causes above panic.
Add printf's included in `#ifdef DIAGNOSTIC' for EDEADLK cases.
Clean up the unexpected busfree handler. We now look directly at the
message that might have caused the bus free to occur instead of looking
at an SCB flag. This makes the handling more robust and also allows for
recovery actions that might cause an "unexpected busfree" to be performed
even if an SCB is not availible to "tag". Most notably, this happens
when we don't find an SCB for a reconnecting target.
to fix a selection timeout problem.
If we can't find an SCB for the reconnecting target, issue a bus device
reset as the SCSI2 spec suggests.
Add a missing call to "add_scb_to_free_list" in the non paging case. In
the non-paging case, the SCBs don't really need to be on the free list,
but putting them there clears the tag field which is something the recovery
code depends on.
Zero the b_dirty{off,end} after cluster-comitting a group of buffers.
With these fixes, I was able to complete a 'make world' with remote src
and obj directories.
