crossing of server mount points properly. The functions
nfsvno_fillattr() and nfsv4_fillattr() were modified to
take the extra arguments that are the mount point, a flag
to indicate that it is a file system root and the mounted
on fileno. The mount point argument needs to be busy when
nfsvno_fillattr() is called, since the vp argument is not
locked.
Reviewed by: kib
MFC after: 2 weeks
invariant and APERF/MPERF MSRs exist but these MSRs never tick. When we
calculate effective frequency from cpu_est_clockrate(), it caused panic of
division-by-zero. Now we test whether these MSRs actually increase to avoid
such foot-shooting.
Reported by: dim
Tested by: dim
from scratch. Remove htole16() calls, rxon.chan is an uint8_t,
ieee80211_chan2ieee() does return an ic_ieee as an int, but I heavily
doubt a htole16() will buy us anything here.
- IWN_TXOP_TO_US is equal to IEEE80211_TXOP_TO_US
- use IEEE80211_DUR_TU
- ieee80211_add_rates/ieee80211_add_xrates are public, use em
- copied ieee80211_add_ssid it is not public
32 bits. Some times compiler inserts unnecessary instructions to preserve
unused upper 32 bits even when it is casted to a 32-bit value. It reduces
such compiler mistakes where every cycle counts.
Therefore, we also need to install the new tmmintrin.h header containing
the related intrinsic functions, similar to xmmintrin.h, emmintrin.h,
etc.
Reported by: George Liaskos <geo.liaskos@gmail.com>
Instead of spinning in a tight loop for up to 15 seconds, polling for device
readiness while it spins up, return reset completion just after PHY reports
"connect well" or 100ms connection timeout. If device was found, use callout
for checking device readiness with 100ms period up to full 31 second timeout.
This fixes system freeze for 5-10 seconds on drives hot plug-in.
mount point crossings correctly. It was testing the wrong flag.
Also, try harder to make sure that the fsid is different than
the one assigned to the client mount point, by hashing the
server's fsid (just to create a different value deterministically)
when it is the same.
MFC after: 2 weeks
details of each rman header, but not the contents of all rman structures
in the system. This is especially useful on platforms where some rmans
have many thousands of entries in rmans, making scrolling through the
output of "show all rman" impractical. Individual rmans can then be viewed
including their contents with "show rman 0xaddr" as usual.
Reviewed by: jhb
- make SATA SIMs announce capabilities to handle SDB with Notification bit;
- make PMP driver honor this SIMs capability;
- make SATA XPT to negotiate and enable this feature for ATAPI devices.
This feature allows supporting SATA ATAPI devices to inform system about
some events happened, that may require attention. In my case this allows
LG GH22LS50 SATA DVR-RW drive to report tray open/close events. Events
reported to CAM in form of AC_SCSI_AEN async. Further they could be used
as a hints for checking device status and reporting media change to upper
layers, for example, via spoiling mechanism of GEOM.
diversity.
This is bit dirty and likely should be revised at a later date,
with an eye to unifying/tidying up the whole diversity setup
and allowing developers to do "tricky stuff" as they desire.
For now, this works.
* add a new method, specifically for doing per-RX packet
antenna diversity
* set that HAL method only if it's Kite and a Kite chip that
does diversity.
* add a diversity flag to the HAL debugging section
* add a check to make sure the kite diversity code doesn't run
on boards that don't require it, as not all Kite chips will
implement it.
* add some debug statements when the diversity code makes
changes to the antenna diversity/combining setup.
controller port readiness (that should set just after PHY ready signal),
reduce wait time from 10s to 1s before trying more aggressive reset method.
This should improve system responsibility in some failure conditions.
