Add a 'X -s <server> -c <client> [-g <gateway>] -i <interface>' subroutine
to the generic debugnet code. The imagined use is both netdump, shown here,
and NetGDB (vaporware). It uses the ddb(4) lexer, with some new extensions,
to parse out IPv4 addresses.
'Netdump' uses the generic debugnet routine to load a configuration and
start a dump, without any netdump configuration prior to panic.
Loosely derived from work by: John Reimer <john.reimer AT emc.com>
Reviewed by: markj
Differential Revision: https://reviews.freebsd.org/D21460
After r339754, the additional interface parameter was accidentally left out
of the default acpi_generic_id_probe implementation. Apparently this does
not cause any real problems, so this fix is mostly stylistic.
No functional change intended.
X-MFC-With: r339754
This allows ddb(4) commands to construct a static dumperinfo during
panic/debug and invoke doadump(false) using the provided dumper
configuration (always inserted first in the list).
The intended usecase is a ddb(4)-time netdump(4) command.
Reviewed by: markj (earlier version)
Differential Revision: https://reviews.freebsd.org/D21448
The in-tree netdump code has always ignored non-directed ARP requests, and
that seems to work most of the time for netdump.
In my work and testing on NetGDB, it seems like sometimes the remote FreeBSD
conversant (the non-panic system) will send broadcast-destination ARP
requests to the debugnet kernel; without this change, those are dropped and
the remote will see EHOSTDOWN "Host is down" errors from the userspace
interface of the network stack.
Discussed with: markj
Similar to INET checksums, lazily validate UDP checksums when the driver has
already performed the check for us. Like debugnet(4) INET checksums,
validation in software is left as future work.
Reviewed by: markj
Differential Revision: https://reviews.freebsd.org/D21745
Debugnet is a simplistic and specialized panic- or debug-time reliable
datagram transport. It can drive a single connection at a time and is
currently unidirectional (debug/panic machine transmit to remote server
only).
It is mostly a verbatim code lift from netdump(4). Netdump(4) remains
the only consumer (until the rest of this patch series lands).
The INET-specific logic has been extracted somewhat more thoroughly than
previously in netdump(4), into debugnet_inet.c. UDP-layer logic and up, as
much as possible as is protocol-independent, remains in debugnet.c. The
separation is not perfect and future improvement is welcome. Supporting
INET6 is a long-term goal.
Much of the diff is "gratuitous" renaming from 'netdump_' or 'nd_' to
'debugnet_' or 'dn_' -- sorry. I thought keeping the netdump name on the
generic module would be more confusing than the refactoring.
The only functional change here is the mbuf allocation / tracking. Instead
of initiating solely on netdump-configured interface(s) at dumpon(8)
configuration time, we watch for any debugnet-enabled NIC for link
activation and query it for mbuf parameters at that time. If they exceed
the existing high-water mark allocation, we re-allocate and track the new
high-water mark. Otherwise, we leave the pre-panic mbuf allocation alone.
In a future patch in this series, this will allow initiating netdump from
panic ddb(4) without pre-panic configuration.
No other functional change intended.
Reviewed by: markj (earlier version)
Some discussion with: emaste, jhb
Objection from: marius
Differential Revision: https://reviews.freebsd.org/D21421
r259680 added support to vt(4) for printing double-width characters.
Remove the comment that claims no support.
MFC after: 3 days
Sponsored by: The FreeBSD Foundation
This can be used to group all threads belonging to a single logical
entity under a common kernel process.
I am planning to use the new interface for ZFS threads.
MFC after: 4 weeks
This change applies some suggestions by delphij from D21979.
A write-only variable is removed.
There is a diagnostic message if the driver does not recognize the chip.
A chained if-statement is converted to a switch.
MFC after: 3 weeks
Older network equipment used the ethertypes 0x9100, 0x9200, and 0x9300 for
outer VLANs, before standardisation introduced 0x88a8.
Submitted by: Lutz Donnerhacke <lutz_donnerhacke.de>
Differential Revision: https://reviews.freebsd.org/D21846
Automatically apply ldscript.kmod.${MACHINE_ARCH} if it exists.
We already have an i386-specific linker script; rename it accordingly.
Note that the linker script is applied when the object files are
partially linked. (For amd64 this is also the final link.)
Reviewed by: imp, kib
Discussed with: jhb
MFC after: 1 week
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D21887
This updates the protection attributes of subranges of the kernel map.
Unlike pmap_protect(), which is typically used for user mappings,
pmap_change_prot() does not perform lazy upgrades of protections.
pmap_change_prot() also updates the aliasing range of the direct map.
Reviewed by: kib
MFC after: 1 month
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D21758
After r352110 the page lock no longer protects a page's identity, so
there is no purpose in locking the page in pmap_mincore(). Instead,
if vm.mincore_mapped is set to the non-default value of 0, re-lookup
the page after acquiring its object lock, which holds the page's
identity stable.
The change removes the last callers of vm_page_pa_tryrelock(), so
remove it.
Reviewed by: kib
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D21823
filling in the same defaults that the current userland module uses.
This allows an old geom_nop.so userland module to work with a new kernel.
Approved by: imp (mentor)
Reviewed by: cem
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D21972
the request. It is the same as gctl_get_paraml() except that the request
is not marked with an error if the parameter is not present.
Approved by: imp (mentor)
Reviewed by: cem
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D21972
Imported BE, much like the activated BE, will not have an origin that we can
fetch/examine for destruction. be_destroy should not return BE_ERR_NOORIGIN
for failure to get the origin property for BE_DESTROY_AUTOORIGIN, because
we don't really know going into it that there's even an origin to be
destroyed.
BE_DESTROY_NEEDORIGIN has been renamed to BE_DESTROY_WANTORIGIN because only
a subset of it *needs* the origin, so 'need' is too strong of verbiage.
This was caught by jenkins and the bectl tests, but kevans failed to run the
bectl tests prior to commit.
Reported by: lwhsu
From Jake:
When updating the device statistics, report whether or not we have
received any pause frames to the iflib stack. This allows the iflib
stack to avoid generating a Tx hang message while the device is paused.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Submitted by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed by: gallatin@
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D21870
From Jake:
Notify the iflib stack of whether we received any pause frames during
the timer window. This allows the stack to avoid reporting a Tx hang due
to the device being paused.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Submitted by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed by: gallatin@
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D21869
From Jake:
The e1000 driver sets the iflib shared context isc_pause_frames value to
the number of received xoff frames. This is done so that the iflib
watchdog timer won't trigger a Tx Hang due to pause frames.
Unfortunately, the function simply sets it to the value of the xoffrxc
counter. Once the device has received a single XOFF packet, the driver
always reports that we received pause frames. This will prevent the Tx
hang detection entirely from that point on.
Fix this by assigning isc_pause_frames to a non-zero value if we
received any XOFF packets in the last timer interval.
We could attempt to calculate the total number of received packets by
doing a subtraction, but the iflib stack only seems to check if
isc_pause_frames is non-zero.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Submitted by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed by: gallatin@
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D21868
Traditionally, toolchain components such as cc, as, and ld have been
built as static executables. The WITH_SHARED_TOOLCHAIN option from
src.conf(5) is meant to link these as regular executables, e.g. using
shared libraries.
The build of ld.lld did not yet check this option. Fix the Makefile so
it will do so now.
Reported by: Mike Cui <cuicui@gmail.com>
PR: 241257
MFC after: 3 days
general is allowed to sleep. Don't enter the epoch for the
whole duration. If some event handlers need the epoch, they
should handle that theirselves.
Discussed with: hselasky
in this driver indicate that the SD_CAPA register is write-once and after
being set one time the values in it cannot be changed. That turns out not
to be the case -- the values written to it survive a reset, but they can
be rewritten/changed at any time.
should be) correct, they lead to the eMMC on a Beaglebone failing to work
in some situations.
The TI sdhci hardware is kind of strange. The first device inherently
supports 1.8v and 3.3v and the abililty to switch between them, and the
other two devices must be set to 1.8v in the sdhci power control register to
operate correctly, but doing so actually makes them run at 3.3v (unless an
external level-shifter is present in the signal path). Even the 1.8v on the
first device may actually be 3.3v (or any other value), depending on what
voltage is fed to the VDDS1-VDDS7 power supply pins on the am335x chip.
Another strange quirk is that the convention for am335x sdhci drivers in
linux and uboot and the am335x boot ROM seems to be to set the voltage in
the sdhci capabilities register to 3.0v even though the actual voltage is
3.3v. Why this is done is a complete mystery to me, but it seems to be
required for correct operation.
If we had complete modern support for the am335x chip we could get the
actual voltages from the FDT data and the regulator framework. But our
am335x code currently doesn't have any regulator framework support.
Reverting to the prior code will get the popular Beaglebone boards working
again.
This is part of the fix for PR 241301, but also requires r353651 for a
complete fix.
PR: 241301
Discussed with: manu
the slot is flagged as 'embedded'.
The features related to embedded and shared slots were added in v3.0 of
the sdhci spec. Hardware prior to v3 sometimes supported 1.8v on non-
removable devices in embedded systems, but had no way to indicate that
via the standard sdhci registers (instead they use out of band metadata
such as FDT data).
This change adds the controller specification version to the check for
whether to filter out the 1.8v selection. On older hardware, the 1.8v
option is allowed to remain. On 3.0 or later it still requires the
embedded-slot flag to remain.
This is part of the fix for PR 241301 (eMMC not detected on Beaglebone).
Changes to the sdhci_ti driver are also needed for a full fix.
PR: 241301
moea_pvo_remove() might remove the last mapping of a page, in which case
it is clearly no longer writeable. This can happen via pmap_remove(),
or when a CoW fault removes the last mapping of the old page.
Reported and tested by: bdragon
Reviewed by: alc, bdragon, kib
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D22044
-o will force the origin to be destroyed unconditionally.
BE_DESTROY_AUTOORIGIN, on the other hand, will only destroy the origin if it
matches the format used by be_snapshot. This lets us clean up the snapshots
that are clearly not user-managed (because we're creating them) while
leaving user-created snapshots in place and warning that they're still
around when the BE created goes away.
This allows to remove a bunch of low level code.
Also, superio(4) provides safer interaction with other drivers
that work with Super I/O configuration registers.
Tested only on PCengines APU2:
superio0: <Nuvoton NCT5104D/NCT6102D/NCT6106D (rev. B+)> at port 0x2e-0x2f on isa0
wbwd0: <Nuvoton NCT6102 (0xc4/0x53) Watchdog Timer> at WDT ldn 0x08 on superio0
The watchdog output is incorrectly wired on that system and the watchdog
does not really do it its job, but the pulse can be seen with a signal
analyzer.
Reviewed by: delphij, bcr (man page)
MFC after: 19 days
Differential Revision: https://reviews.freebsd.org/D21979
New BEs can be created from either an existing snapshot or an existing BE.
If an existing BE is chosen (either implicitly via 'bectl create' or
explicitly via 'bectl create -e foo bar', for instance), then bectl will
create a snapshot of the current BE or "foo" with be_snapshot, with a name
formatted like: strftime("%F-%T") and a serial added to it.
This commit adds the needed bits for libbe or consumers to determine if a
snapshot names matches one of these auto-created snapshots (with some light
validation of the date/time/serial), and also a be_destroy flag to specify
that the origin should be automatically destroyed if possible.
A future commit to bectl will specify BE_DESTROY_AUTOORIGIN by default so we
clean up the origin in the most common case, non-user-managed snapshots.
This is where it logically belongs.
The change allows to drop a bunch of low lewel code.
Reviewed by: gonzo
MFC after: 19 days
Differential Revision: https://reviews.freebsd.org/D21980
Arm updates these with each new architecture revision. To help keep them
updated use a collection of tables to hold the needed information to
decode these registers.
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D22020
The timespec struct holds a seconds value in a time_t and a nanoseconds
value in a long. On most architectures these are the same size, however
on 32-bit architectures other than i386 time_t is 8 bytes and long is
4 bytes.
Most ABIs will then pad a struct holding an 8 byte and 4 byte value to
16 bytes with 4 bytes of padding. When copying one of these structs the
compiler is free to copy the padding if it wishes.
In this case the padding may contain kernel data that is then leaked to
userspace. Fix this by copying the timespec elements rather than the
entire struct.
This doesn't affect Tier-1 architectures so no SA is expected.
admbugs: 651
MFC after: 1 week
Sponsored by: DARPA, AFRL
