been around for a long time now (7.1-ish or even earlier); assume
they are present. These includes MSI, TSO, LRO, VLAN, INTR_FILTERS,
FIRMWARE, etc.
Also, eliminate some dead code and clean up in other places as part
of this quick once-over.
MFC after: 1 week
- support for the new Gen-2, BT, and LP-CR cards.
- T3 firmware 7.7.0
- shared "common code" updates.
Approved by: gnn (mentor)
Obtained from: Chelsio
MFC after: 1 month
- remove mbuf iovec - useful, but adds too much complexity when isolated to
the driver
- remove driver private caching - insufficient benefit over UMA to justify
the added complexity and maintenance overhead
- remove separate logic for managing multiple transmit queues, with the
new drbr routines the control flow can be made to much more closely resemble
legacy drivers
- remove dedicated service threads, with per-cpu callouts one can get the same
benefit much more simply by registering a callout 1 tick in the future if there
are still buffered packets
- remove embedded mbuf usage - Jeffr's changes will (I hope) soon be integrated
greatly reducing the overhead of using kernel APIs for reference counting
clusters
- add hysteresis to descriptor coalescing logic
- add coalesce threshold sysctls to allow users to decide at run-time
between optimizing for forwarding / UDP or optimizing for TCP
- add once per second watchdog to effectively close the very rare races
occurring from coalescing
- incorporate Navdeep's changes to the initialization path required to
convert port and adapter locks back to ordinary mutexes (silencing BPF
LOR complaints)
- enable prefetches in get_packet and tx cleaning
Reviewed by: navdeep@
MFC after: 2 weeks
1) Add a sysctl that will say what type of PHYs exist on the card.
2) Fix a bug that occurs when an AEL 2005 PHY resets without a transciever
in the card.
3) Unify the PHY link detection code.
Obtained from: Navdeep Parhar
MFC after: 10 days
Firmware upgraded to 7.1.0 (from 5.0.0).
T3C EEPROM and SRAM added; Code to update eeprom/sram fixed.
fl_empty and rx_fifo_ovfl counters can be observed via sysctl.
Two new cxgbtool commands to get uP logic analyzer info and uP IOQs
Synced up with Chelsio's "common code" (as of 03/03/09)
Submitted by: Navdeep Parhar at Chelsio
Reviewed by: gnn
MFC after: 2 weeks
packet loss, of between 10-30%. The fix is to put the PHY into
and take it out of local loopback mode when resetting the interface.
Obtained from: Chelsio Inc.
MFC after: 3 days
when it sees only received packets. In some cases where a device only
recieves data it mistakenly thinks that its transmitting side is broken
and resets the device.
Obtained from: Chelsio Inc.
MFC after: 3 days
1) Fix a bug in dealing with the Alerus 1006 PHY which prevented the
device from ever coming back up once it had been set to down.
2) Add a kernel tunable (hw.cxgb.snd_queue_len) which makes it possible
to give the device more than IFQ_MAXLEN entries in its send queue. The
default remains 50.
3) Add code to place the card'd identification and serial number into
its description (%desc) so that users can tell which card they have
installed.
- add support for T3C
- add DDP support (zero-copy receive)
- fix TOE transmit of large requests
- fix shutdown so that sockets don't remain in CLOSING state indefinitely
- register listeners when an interface is brought up after tom is loaded
- fix setting of multicast filter
- enable link at device attach
- exit tick handler if shutdown is in progress
- add helper for logging TCB
- add sysctls for dumping transmit queues
- note that TOE wxill not be MFC'd until after 7.0 has been finalized
MFC after: 3 days
- return the error from cxgb_tx_common so that when an error is hit we dont
spin forever in the taskq thread
- remove unused rxsd_ref
- simplify header_offset calculation for embedded mbuf headers
- fix memory leak by making sure that mbuf header initialization took place
- disable printf's for stalled queue, don't do offload/ctrl queue restart
when tunnel queue is restarted
- add more diagnostic information about the txq state
- add facility to dump the actual contents of the hardware queue using sysctl
and t3_push_frames).
- Import latest changes to cxgb_main.c and cxgb_sge.c from toestack p4 branch
- make driver local copy of tcp_subr.c and tcp_usrreq.c and override tcp_usrreqs so
TOE can also functions on versions with unmodified TCP
- add cxgb back to the build
- fix the use after free seen when sending packets small enough to fit as an immediate
and bpf peers are present
- update to firmware rev 4.7 along with various small vendor fixes
Supported by: Chelsio
Approved by: re (blanket)
MFC after: 3 days
- remove cpl->iff panic - we can't know the port number from the rspq on the 4-port
- pick the ifnet based on the interface in the CPL header
- switch to using qset 0 for egress on the 4-port for now - may change
when we start using RSS
- move ether_ifdetach to before the port lock gets deinitialized to avoid
hang in the case where there are BPF peers (cxgb_ioctl is called indirectly
when BPF peers are present)
- don't call t3_mac_reset if multiport is set, this was causing tx errors
by misconfiguring the MAC on the 4-port
- change V_TXPKT_INTF to use txpkt_intf as the interfaces are not contiguous
- free the mbuf immediately in the case where the payload is small enough to be copied
into the rspq
- only update the coalesce timer if for a queue if packets were taken off of it
- add in missed 20ms DELAY in initializaton vsc8211
- prompt MFC as this only applies to the 4-port which is currently completely
broken - OK'd by kensmith
Supported by: Chelsio
Approved by: re (blanket)
MFC after: 0 days
- update to firmware version 4.1.0
- switch over to standard method for initializing cdevs (contributed by scottl@)
- break out timer_reclaim_task to be per-port
- move msix teardown into separate function
- fix bus_setup_intr for msi-x for the multi-port case so that msi-x resources
are not corrupted on unload
- handle 10/100/1000 base-T media and auto negotiation
- bind qset to cpu even for singleq case
- white space cleanups
- remove recursive PORT_LOCK
- move mtu setting to separate function
- stop and re-init port when changing mtu
- replace all direct references to m_data with calls to mtod
- handle attach failure better by not trying to de-initialize
taskqueues when they have not been allocated
- no longer default to jumbo frames
Sponsored by: Chelsio
MFC after: 3 days
- upgrade to reflect state of 1.0.0.86
- move from firmware rev 3.2 to 4.0.0
- import driver bits for offload functionality
- remove binary distribution clause from top level files as it
runs counter to the intent of purely supporting the hardware
MFC after: 3 days
(with the notable exception of improvements for using multiple TX queues)
This adds support for the T3B2 ASIC rev
Obtained from: Chelsio
MFC after: 3 days
