clearing hazards.
This revision makes currently known MIPS32 Release 2 and Release 3 CPUs use
the EHB instruction when clearing hazards. So far the MIPS 74K and MIPS1004K
(somewhat) were already using the EHB. Now we add more r2 and r3 CPUs to
this list.
Also, for the cases of MIPS coherent processing systems (currently 1004K,
1074K, interAptiv and proAptiv) - define proper CCA attributes.
Submitted by: Stanislav Galabov <sgalabov@gmail.com>
Reviewed by: imp
Differential Revision: https://reviews.freebsd.org/D5078
to open the device in exclusive mode as, without this, the firmware may
also be reading packets off the interface leading to a race.
Reviewed by: emaste
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D4132
the processor and debug state registers. A flag has been added to the pcb
to tell us when to enable single stepping for a given thread.
Reviewed by: kib
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D4730
function is only called from vm_page_startup() and vm_reserv_startup().
I.e. during vm subsystem initialization. As VM_PROT_WRITE is always
used in these calls, the typo did not have any effect. Likely, it's
the reason why it wasn't discovered so long.
This revision does the following renames:
CPU_MIPS24KC -> CPU_MIPS24K
CPU_MIPS74KC -> CPU_MIPS74K
CPU_MIPS1004KC -> CPU_MIPS1004K
It also adds the following new CPU_MIPSxxx options:
CPU_MIPS24KE, CPU_MIPS34K, CPU_MIPS1074K, CPU_INTERAPTIV, CPU_PROAPTIV
CPU_MIPSxxxxKC is limiting and possibly misleading as it implies the
MIPSxxxxK CPU has no FPU.
It would be better if the CPUs are named after their standard functionalities
only and the presence or absence of FPU can then be controlled via the
CPU_HAVEFPU option.
I will send out another dependent revision that moves MIPS 32 r2 and r3
CPUs to use the EHB instruction for clearing hazards instead of NOP/SSNOP.
Submitted by: Stanislav Galabov <sgalabov@gmail.com>
Reviewed by: imp
Differential Revision: https://reviews.freebsd.org/D5077
MD_ROOT_SIZE and embed_mfs.sh were basically retired as part of
https://reviews.freebsd.org/D2903 .
However, when building a kernel with 'options MD_ROOT_SIZE' specified, this
results in a non-working MFS, as within sys/dev/md/md.c we fall within the
wrong # ifdef.
This patch implements the following:
* Allow kernels to be built without the MD_ROOT_SIZE option, which results
in a kernel built as per D2903.
* Allow kernels to be built with the MD_ROOT_SIZE option, which results
in a kernel built similarly to the pre-D2903 way, with the following
differences:
* The MFS is now put in a separate section within the kernel (oldmfs,
so it differs from the mfs section introduced by D2903).
* embed_mfs.sh is changed, so it looks up the oldmfs section within the
kernel, gets its size and offset, sees if the MFS will fit within the
allocated oldmfs section and only if all is well does a dd of the MFS
image into the kernel.
Submitted by: Stanislav Galabov <sgalabov@gmail.com>
Reviewed by: brooks, imp
Differential Revision: https://reviews.freebsd.org/D5093
Some hardware supports AES acceleration but not SHA1, e.g., AES-NI
extensions. It is useful to have accelerated AES even if SHA1 must be
software.
Suggested by: asomers
Reviewed by: asomers, dfr
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D5146
causes watchdog timeouts when using TSO4 at link speeds below
Gigabit, at least with 82573E. So disable the assist automatically
when at lower speeds.
Submitted by: jfv
Approved by: erj
Obtained from: D3162
MFC after: 3 days
The PT_{GET,SET}FPREGS requests use 'struct fpreg' and the NT_FPREGSET
core note stores a copy of 'struct fpreg'. As with x86 and the floating
point state there compared to the extended state in XSAVE, struct fpreg
on powerpc now only holds the 'base' FP state, and setting it via
PT_SETFPREGS leaves the extended vector state in a thread unchanged.
Reviewed by: jhibbits
Differential Revision: https://reviews.freebsd.org/D5004
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Ned Bass <bass6@llnl.gov>
Reviewed by: Tim Chase <tim@chase2k.com>
Approved by: Gordon Ross <gwr@nexenta.com>
Author: Andriy Gapon <avg@icyb.net.ua>
illumos/illumos-gate@e7e978b1f7
During the update process in sa_modify_attrs(), the sizes of existing
variably-sized SA entries are obtained from sa_lengths[]. The case where
a variably-sized SA was being replaced neglected to increment the index
into sa_lengths[], so subsequent variable-length SAs would be rewritten
with the wrong length. This patch adds the missing increment operation
so all variably-sized SA entries are stored with their correct lengths.
Another problem was that index into attr_desc[] was increased even when
an attribute was removed. If that attribute was not the last attribute,
then the last attribute was lost.
print until cncheckc returned a non -1, i.e. a character had been entered.
After this change it would print only if cncheckc returned a character.
As this was before each call to db_mach_vtrace the normal outcome was
nothing was printed.
With this change 'show ktr /a' will now keep printing until the user stops
the command with a key press, or there is no more entries to print.
Fix ixgbe reporting of flow control autoneg when running under DBG 1
Reviewed by: erj
MFC after: 2 days
Sponsored by: Multiplay
Differential Revision: https://reviews.freebsd.org/D5089
Setup phy and gbic power as per Linux 4.3.13 driver.
This fixes link not detected on X540-AT2 after booting to Linux which turns
the phy power off on detach.
Reviewed by: sbruno
MFC after: 2 days
Sponsored by: Multiplay
Differential Revision: https://reviews.freebsd.org/D5107
new addresses during restart. If this is not done, restart doesn't
work when the local socket is IPv4 only and the peer uses
IPv4 and IPv6 addresses.
MFC after: 3 days.
Fix the inverted set of interrupts being used as the mask for ixl.
Without this ixl devices fail to detect link state changes.
Reviewed by: erj, sbruno
MFC after: 2 days
Sponsored by: Multiplay
There is no explanation why IPI ID is incremented here by "16".
This should have been removed in r285533 but somehow survived.
Reviewed by: wma
Obtained from: Semihalf
Sponsored by: Cavium
Differential Revision: https://reviews.freebsd.org/D5120
