rl(4) driver and put it in a new re(4) driver. The re(4) driver shares
the if_rlreg.h file with rl(4) but is a separate module. (Ultimately
I may change this. For now, it's convenient.)
rl(4) has been modified so that it will never attach to an 8139C+
chip, leaving it to re(4) instead. Only re(4) has the PCI IDs to
match the 8169/8169S/8110S gigE chips. if_re.c contains the same
basic code that was originally bolted onto if_rl.c, with the
following updates:
- Added support for jumbo frames. Currently, there seems to be
a limit of approximately 6200 bytes for jumbo frames on transmit.
(This was determined via experimentation.) The 8169S/8110S chips
apparently are limited to 7.5K frames on transmit. This may require
some more work, though the framework to handle jumbo frames on RX
is in place: the re_rxeof() routine will gather up frames than span
multiple 2K clusters into a single mbuf list.
- Fixed bug in re_txeof(): if we reap some of the TX buffers,
but there are still some pending, re-arm the timer before exiting
re_txeof() so that another timeout interrupt will be generated, just
in case re_start() doesn't do it for us.
- Handle the 'link state changed' interrupt
- Fix a detach bug. If re(4) is loaded as a module, and you do
tcpdump -i re0, then you do 'kldunload if_re,' the system will
panic after a few seconds. This happens because ether_ifdetach()
ends up calling the BPF detach code, which notices the interface
is in promiscuous mode and tries to switch promisc mode off while
detaching the BPF listner. This ultimately results in a call
to re_ioctl() (due to SIOCSIFFLAGS), which in turn calls re_init()
to handle the IFF_PROMISC flag change. Unfortunately, calling re_init()
here turns the chip back on and restarts the 1-second timeout loop
that drives re_tick(). By the time the timeout fires, if_re.ko
has been unloaded, which results in a call to invalid code and
blows up the system.
To fix this, I cleared the IFF_UP flag before calling ether_ifdetach(),
which stops the ioctl routine from trying to reset the chip.
- Modified comments in re_rxeof() relating to the difference in
RX descriptor status bit layout between the 8139C+ and the gigE
chips. The layout is different because the frame length field
was expanded from 12 bits to 13, and they got rid of one of the
status bits to make room.
- Add diagnostic code (re_diag()) to test for the case where a user
has installed a broken 32-bit 8169 PCI NIC in a 64-bit slot. Some
NICs have the REQ64# and ACK64# lines connected even though the
board is 32-bit only (in this case, they should be pulled high).
This fools the chip into doing 64-bit DMA transfers even though
there is no 64-bit data path. To detect this, re_diag() puts the
chip into digital loopback mode and sets the receiver to promiscuous
mode, then initiates a single 64-byte packet transmission. The
frame is echoed back to the host, and if the frame contents are
intact, we know DMA is working correctly, otherwise we complain
loudly on the console and abort the device attach. (At the moment,
I don't know of any way to work around the problem other than
physically modifying the board, so until/unless I can think of a
software workaround, this will have do to.)
- Created re(4) man page
- Modified rlphy.c to allow re(4) to attach as well as rl(4).
Note that this code works for the sample 8169/Marvell 88E1000 NIC
that I have, but probably won't work for the 8169S/8110S chips.
RealTek has sent me some sample NICs, but they haven't arrived yet.
I will probably need to add an rlgphy driver to handle the on-board
PHY in the 8169S/8110S (it needs special DSP initialization).
of the infrastructure for the gamma driver which was removed a while back.
The DRM_LINUX option is removed because the handler is now provided by the
linux compat code itself.
ethernet controller. The driver has been tested with the LinkSys
USB200M adapter. I know for a fact that there are other devices out
there with this chip but don't have all the USB vendor/device IDs.
Note: I'm not sure if this will force the driver to end up in the
install kernel image or not. Special magic needs to be done to exclude
it to keep the boot floppies from bloating again, someone please
advise.
mechanism, and then excludes device drivers which have not been tested or
are known to not work with more than 4G of ram.
Sponsored by: DARPA, Network Associates Laboratories
This keeps the logical cpu's halted in the idle loop. By default
the logical cpu's are halted at startup. It is also possible to
halt any cpu in the idle loop now using machdep.hlt_cpus.
Examples of how to use this:
machdep.hlt_cpus=1 halt cpu0
machdep.hlt_cpus=2 halt cpu1
machdep.hlt_cpus=4 halt cpu2
machdep.hlt_cpus=3 halt cpu0,cpu1
Reviewed by: jhb, peter
included in XFree86 4.3, but includes some fixes. Notable changes include
Radeon 8500-9100 support, PCI Radeon/Rage 128 support, transform & lighting
support for Radeons, and vblank syncing support for r128, radeon, and mga.
The gamma driver was removed due to lack of any users.
Fixed memory leak in the "nodevice" option implementation.
Use these instead of sed(1) in MD NOTES.
Use a single makefile (sys/conf/makeLINT.mk) to generate
LINT for all architectures. (Previous versions missed
the LINT dependency on Makefile, and i386 version also
missed the dependency on ${NOTES}.)
Fixed bugs in the previous NOTES conversion using the
"nodevice" token and sed(1):
- i386 LINT lost "device pst".
- pc98 LINT lost SC_*, MAXCONS and KBD_DISABLE_KEYMAP_LOAD
options, and got needless DPT_* options.
- Added nooptions PPC_DEBUG, PPC_PROBE_CHIPSET, KBD_INSTALL_CDEV
to sparc64 LINT so that it has a chance to config(8).
This basically returns us to where we were before.
frequency in Hz. The default is still 33.333 MHz. Please notice
that the number is round to a multiple of four internally so it may
not read back exactly the same as written.
Add compile time ELAN_XTAL option to override the 33.333 MHz default.
Add compile time ELAN_PPS option to enable code for high precision
(250 nanoseconds) timestamping of external signals.
GENERIC. Each device can be re-enabled at startup time by unsetting the
disabled hint in the loader.
Requested by: mdodd
Approved by: re
Prodded by: rwatson
ACL configuration changes, this shouldn't result in different code paths
for file systems not explicitly configured for ACLs by the system
administrator. For UFS1, administrators must still recompile their
kernel to add support for extended attributes; for UFS2, it's sufficient
to enable ACLs using tunefs or at mount-time (tunefs preferred for
reliability reasons). UFS2, for a variety of reasons, including
performance and reliability, is the preferred file system for use with
ACLs.
Approved by: re
needed to be quoted (to get a C string literal), not the value itself.
Fixed the value of SC_CUT_SEPCHARS. Setting this value would have had no
effect even if it were used, since the value was the same as the default.
The above bugs had no effect except to set bad examples, since test
coverage of SC_CUT_SEPCHARS is broken by enabling a negative option.
Removed (unquoted) double quotes for all options. They were all bogus
since they had no effect except to make non-strings look like strings.
Most of the non-strings were expressions. The value of INIT_PATH is
a non-string since it is stringified later (unlike SC_CUT_SEPCHARS).
Fixed parenthesization errors inside bogus quotes (parenthesize values
if they have more than one token in them but don't parenthesize single
tokens).
This is most beneficial for vmware client os installs.
Reviewed by: jmallet, iedowse, tlambert2@mindspring.com
MFC After: never, -STABLE does not currently use this instruction
that add an instance of themselves. The npx(4) driver doesn't even check
the npx 'port' hint but hardcodes IO_NPX instead. The npx(4) driver also
will use isa IRQ 13 (on x86, 8 on pc98) by default if no 'irq' hint is
specified, so we don't need that hint either.
NB: But it will enable it in all kernels not having options "NO_GEOM"
Put the GEOM related options into the intended order.
Add "options NO_GEOM" to all kernel configs apart from NOTES.
In some order of controlled fashion, the NO_GEOM options will be
removed, architecture by architecture in the coming days.
There are currently three known issues which may force people to
need the NO_GEOM option:
boot0cfg/fdisk:
Tries to update the MBR while it is being used to control
slices. GEOM does not allow this as a direct operation.
SCSI floppy drives:
Appearantly the scsi-da driver return "EBUSY" if no media
is inserted. This is wrong, it should return ENXIO.
PC98:
It is unclear if GEOM correctly recognizes all variants of
PC98 disklabels. (Help Wanted! I have neither docs nor HW)
These issues are all being worked.
Sponsored by: DARPA & NAI Labs.
if compiling with I686_CPU as a target. CPU_DISABLE_SSE will prevent
this from happening and will guarantee the code is not compiled in.
I am still not happy with this, but gcc is now generating code that uses
these instructions if you set CPUTYPE to p3/p4 or athlon-4/mp/xp or higher.
lnc(4) will attach to AMD PCnet/FAST NICs if pcn(4) does not attach.
I.e. pcn(4) gets first chance. There is a problem however in that pcn(4)
was moved out of the install kernel so that the module would be used.
This however causes bad installs if one has an AMD PCnet/FAST NIC.
i4bq931, i4b, isic, iwic, ifpi, ifpi2, ifpnp, ihfc, and itjc are
no longer count devices. Also remove a few other instances of N<DEVICE>
being used to control compilation of whole files.
Reviewed by: hm
This is an architecture that present a thing message passing interface
to the OS. You can query as to how many ports and what kind are attached
and enable them and so on.
A less grand view is that this is just another way to package SCSI (SPI or
FC) and FC-IP into a one-driver interface set.
This driver support the following hardware:
LSI FC909: Single channel, 1Gbps, Fibre Channel (FC-SCSI only)
LSI FC929: Dual Channel, 1-2Gbps, Fibre Channel (FC-SCSI only)
LSI 53c1020: Single Channel, Ultra4 (320M) (Untested)
LSI 53c1030: Dual Channel, Ultra4 (320M)
Currently it's in fair shape, but expect a lot of changes over the
next few weeks as it stabilizes.
Credits:
The driver is mostly from some folks from Jeff Roberson's company- I've
been slowly migrating it to broader support that I it came to me as.
The hardware used in developing support came from:
FC909: LSI-Logic, Advansys (now Connetix)
FC929: LSI-Logic
53c1030: Antares Microsystems (they make a very fine board!)
MFC after: 3 weeks
and function) with existing configuration choices. Arguably if
ALT_BREAK_TO_DEBUGGER was present, so should have been
BREAK_TO_DEBUGGER. Regardless, it broke the option sort order in
these kernel configuration files.
Requested by: bde
ever connect a SCSI Cdrom/Tape/Jukebox/Scanner/Printer/kitty-litter-scooper
to your high-end RAID controller. The interface to the arrays is still
via the block interface; this merely provides a way to circumvent the
RAID functionality and access the SCSI buses directly. Note that for
somewhat obvious reasons, hard drives are not exposed to the da driver
through this interface, though you can still talk to them via the pass
driver. Be the first on your block to low-level format unsuspecting
drives that are part of an array!
To enable this, add the 'aacp' device to your kernel config.
MFC after: 3 days
drivers with MI portions into the MI notes. Device drivers such as busses
like the isa, eisa, and pci devices are now in the MD NOTES section even
though they have some MI code. This will ensure that only the proper bits
of device drivers will be included due to the optional bits dependent on
the busses in sys/conf/files. This commit also takes the stance that since
hints are ignored in NOTES anyways, it is ok to include hints for a bus
that may not be present.
Advice from: bde
Unfortunately, this level doesn't really provide enough granularity. We
probably need several MI NOTES type files for things that are shared by
several architectures but not by all. For example, the PCI options could
live in a NOTES.pci.
This also updates the Makefile for i386 to generate LINT. The only changes
in the generated LINT are the order of various options.
Suggestions for improvement welcome.
and commenting of NETSMB, NETWMBCRYPTO, and SMBFS. In NOTES, they
had all floated to the bottom of the file with the list of seemingly
random and unclassified kernel options. This change moves them back
up to the network protocol and file system areas, and also documents
the dependencies.
the structure definitions come from NetBSD to make it easier to share card
definitions. The driver only acts as a shim between the pci bus and the
sio driver. Later pci parallel ports could also be supported through this
driver. Support for most single and multiport pci serial cards should be
as simple as adding its definition to pucdata.c
Tested with the following pci cards:
Moxa Industio CP-114, 4 port RS-232,RS-422/485
Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports
Netmos NM9835 PCI-2S-550, 2 port RS-232
ACPI_NO_SEMAPHORES, ASR_MEASURE_PERFORMANCE, AST_DEBUG, ATAPI_DEBUG,
ATA_DEBUG, BKTR_ALLOC_PAGES, BROOKTREE_ALLOC_PAGES, CAPABILITIES,
COMPAT_SUNOS, CV_DEBUG, MAXFILES, METEOR_TEST_VIDEO, NDEVFSINO,
NDEVFSOVERFLOW, NETGRAPH_BRIDGE, NETSMB, NETSMBCRYPTO, PFIL_HOOKS,
SIMOS, SMBFS, VESA_DEBUG, VGA_DEBUG.
Start using #! to comment out negative options and ## to comment out
broken options.
atapi-all.c:
Fixed rotted bits that were hiding under ATAPI_DEBUG.
atapi-cd.c:
#include "opt_ata.h" so that ACD_DEBUG is actually visible.
ata/atapi-tape.c
#include "opt_ata.h" so that AST_DEBUG is actually visible.
SMP we'd like as much feedback as possible from users about possible
locking problems as early as possible.
To negate most of the performance impact I've also enabled
WITNESS_SKIPSPIN. I've done this as we've been running WITNESS
over the spinlock code for a while without incident and it goes a
long way to making the performance problems of WITNESS much more
bearable.
Users who should be running current should know about turning WITNESS
off for performance reasons.
That said and done, WITNESS could/should be made into a tuneable,
but we'll leave that as an excersize to those that want to disable
it without a kernel recompile.
descriptors. This simplifies code for jumbo frames.
- Cleaned up coding conventions to make code more unix-like.
- Cleaned up code in if_em_fxhw.c and if_em_phy.c.
Added relevant comments.
MFC after: 1 week
slower, and may be impeding adoption of -CURRENT by developers. We
recommend turning on WITNESS by default on crash boxes, and when doing
locking development. It will probably get turned on by default for a week
or two following any major locking commits, also.
Approved by: all and sundry (jhb, phk, ...)
feature bit on newer Athlon CPUs if the BIOS has forgotten to enable
it.
This patch was constructed using some info made available by John
Clemens at http://www.deater.net/john/PavilionN5430.html
Reviewed by: -audit
MFC after: 3 weeks
prior ICP Vortex models. This driver was developed by Achim Leubner
of Intel (previously with ICP Vortex) and Boji Kannanthanam of Intel.
Submitted by: "Kannanthanam, Boji T" <boji.t.kannanthanam@intel.com>
MFC after: 2 weeks
for use on machines with untrusted local users, for security as well
as stability reasons.
o Lack of clarity pointed out by: David Rufino <dr@soniq.net> via bugtraq.
defeats the point of LINT to comment out positive options.
Fixed style bugs in rev.1.973:
- disordering of PCI options list.
- missing space after "options".
- line longer than 80 characters.
- bogus quoting of "BIOS".
been misled to believe by unknown parties. It probably *should* be an option,
but the runtime value is controlled by a tunable, which Ought To Be Enough.
to do with "dropped packets." Any packets matching rules with the
'log' directive are logged regardless of the action, drop, pass,
divert, pipe, etc.
MFC after: 1 day
built without support for miibus PHYs. Most ed cards don't need
miibus support, so it's useful to be able to avoid the bloat of
all the mii devices for small fixed-purpose kernels.
ethernet controllers. This adds support for the 3Com 3c996-T, the
SysKonnect SK-9D21 and SK-9D41, and the built-in gigE NICs on
Dell PowerEdge 2550 servers. The latter configuration hauls ass:
preliminary measurements show TCP speeds of over 900Mbps using
only normal size frames.
TCP/IP checksum offload, jumbo frames and VLAN tag insertion/stripping
are supported, as well as interrupt moderation.
Still need to fix autonegotiation support for 1000baseSX NICs, but
beyond that, driver is pretty solid.
- SC_CUT_SPACES2TABS - when copying text into the cut buffer convert leading
spaces into the tabs;
- SC_CUT_SEPCHARS="XYZ" - treat supplied characters as possible words
separators when the driver searches for words boundaries when doing cut
operation.
Also unify cut code a bit to decrease amount of duplicated code. This fixes
line cut mode, so that it is no longer pads line with useless spaces.
Approved by: ru
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
level implementation stuff out of machine/globaldata.h to avoid exposing
UPAGES to lots more places. The end result is that we can double
the kernel stack size with 'options UPAGES=4' etc.
This is mainly being done for the benefit of a MFC to RELENG_4 at some
point. -current doesn't really need this so much since each interrupt
runs on its own kstack.
then one can restart from a panic by resetting the panicstr variable to
NULL. This commit conditionalizes the previously committed functionality
on this variable. It also removes the __dead2 attribute from the panic()
function so that when one continues from a panic() the behavior will
be predictable.
