solving a possible panic when snd_ai2s is loaded at boot time. Also change
the device setup to indicate to the pcm layer that the device is MPSAFE.
Submitted by: Marco Trillo
Suggestions by: Ariff Abdullah
o add missing channel flags for ECM, indoor, and outdoor constraints
o use HT capabilities to short-circuit HT20/HT40 channel construction
o rewrite 1/2 and 1/4 width channel handling yet again; previously
we assumed there was a full-width version of the channel in the
calibration table but that's not always true (e.g. for the Public
Safety Band), now we first check the calibration table for the
exact channel we want then fall back to the heuristics we used before
o fix HT channel construction; wasn't adjusting band edges for HT40
channel bandwidth requirements
- ath(4) is the last listed device, so make it's comment last as well
- since we have hints for le(4), bring it back by inserting commented
out line until I check, if it can be safely enabled.
- bring snc(4) explanation
- put pmtimer comment together with other drivers' comments in a block
- bring comments for canbus, canbepm, pmc
olpt comment has been left blank, since I don't know how does this
driver differ from other printer drivers.
- leave pmtimer comment that is common to other architectures.
- bring pbio explanation to the block comment relating to other
drivers in the same block.
- remove misleading nve/nfe comments, which make it hard to
distinguish those two at a first glance
- bring pbio documentation to the block comment together with
other drivers
I also brought commented out line responsible for si(4), since it
seems to compile and already has respective comment in this file.
sequence of pathname components. We walk the list building a string in
the caller's passed in buffer. Currently this only handles path names
in CS8 (character set 8) as that is what mkisofs generates for UDF images.
MFC after: 1 month
global NOTES file.
cx(4) driver isn't present in this file, though it could be. However, cx(4)
seems to be more or less dead -- it hasn't been linked to the modules build,
and after TTY-ng transformations it doesn't compile.
Remove it until cx(4) is broken.
need to explicitly list it here once again. This removes:
WARNING: duplicate option `DEV_URAL' encountered.
WARNING: duplicate device `ural' encountered.
Warnings when compiling LINT on amd64.
- correct format strings
- fill opt_agp.h if AGP_DEBUG is defined
- bring AGP_DEBUG to LINT by mentioning it in NOTES
This should hopefully fix a warning that was...
Found by: Coverity Prevent(tm)
CID: 3676
Tested on: amd64, i386
- Add a separate set of vnode operations that inherits from the fifo ops
and use it for fifo nodes.
- Add a VOP_SETATTR() method that allows setting the size (by silently
ignoring the requests) of fifos. This is to allow O_TRUNC opens of
fifo devices (e.g. I/O redirection in shells using ">").
- Add a VOP_PRINT() handler while I'm here.
- Align the fifo output in fifo_print() with other vn_printf() output.
- Remove the leading space from lockmgr_printinfo() so its output lines up
in vn_printf().
- lockmgr_printinfo() now ends with a newline, so remove an extra newline
from vn_printf().
of devvp becomes VBAD, which UFS incorrectly interprets as snapshot
vnode, which in turns causes panic. Fix it by replacing '!= VCHR'
with '== VREG'.
With this fix in place, you should no longer be able to panic the system
by removing a device with an UFS filesystem mounted from it - assuming
you don't use softupdates.
Reviewed by: kib
Tested by: pho
Approved by: rwatson (mentor)
Sponsored by: FreeBSD Foundation
Back in 1.1 of kern_sysctl.c the sysctl() routine wired the "old" userland
buffer for most sysctls (everything except kern.vnode.*). I think to prevent
issues with wiring too much memory it used a 'memlock' to serialize all
sysctl(2) invocations, meaning that only one user buffer could be wired at
a time. In 5.0 the 'memlock' was converted to an sx lock and renamed to
'sysctl lock'. However, it still only served the purpose of serializing
sysctls to avoid wiring too much memory and didn't actually protect the
sysctl tree as its name suggested. These changes expand the lock to actually
protect the tree.
Later on in 5.0, sysctl was changed to not wire buffers for requests by
default (sysctl_handle_opaque() will still wire buffers larger than a single
page, however). As a result, user buffers are no longer wired as often.
However, many sysctl handlers still wire user buffers, so it is still
desirable to serialize userland sysctl requests. Kernel sysctl requests
are allowed to run in parallel, however.
- Expose sysctl_lock()/sysctl_unlock() routines to exclusively lock the
sysctl tree for a few places outside of kern_sysctl.c that manipulate
the sysctl tree directly including the kernel linker and vfs_register().
- sysctl_register() and sysctl_unregister() require the caller to lock
the sysctl lock using sysctl_lock() and sysctl_unlock(). The rest of
the public sysctl API manage the locking internally.
- Add a locked variant of sysctl_remove_oid() for internal use so that
external uses of the API do not need to be aware of locking requirements.
- The kernel linker no longer needs Giant when manipulating the sysctl
tree.
- Add a missing break to the loop in vfs_register() so that we stop looking
at the sysctl MIB once we have changed it.
MFC after: 1 month
in fallback_mount() function.
Add a comment to indicate that the fallback_mount() function
should eventually go away.
Submitted by: Jaakko Heinonen <jh saunalahti fi>
sysctls during a linker file unload. We drop the lock when doing similar
operations during a linker file load. To close races, clear the LINKED
flag before dropping the lock so that the linker file is no longer visible
to userland.
MFC after: 1 week
o change tdma packet drop msg when ack required to ATH_DEBUG_TDMA
(ATH_DEBUG_XMIT is too noisy)
o add a debug msg for raw packet drop due to interface down/invalid
o add stats for these two cases
o explain how another drop case is handled
