most devsw referenced functions are now static, as they are
in the same file as their devsw structure. I've also added DEVFS
support for nearly every device in the system, however
many of the devices have 'incorrect' names under DEVFS
because I couldn't quickly work out the correct naming conventions.
(but devfs won't be coming on line for a month or so anyhow so that doesn't
matter)
If you "OWN" a device which would normally have an entry in /dev
then search for the devfs_add_devsw() entries and munge to make them right..
check out similar devices to see what I might have done in them in you
can't see what's going on..
for a laugh compare conf.c conf.h defore and after... :)
I have not doen DEVFS entries for any DISKSLICE devices yet as that will be
a much more complicated job.. (pass 5 :)
pass 4 will be to make the devsw tables of type (cdevsw * )
rather than (cdevsw)
seems to work here..
complaints to the usual places.. :)
That's EVERY SINGLE driver that has an entry in conf.c..
my next trick will be to define cdevsw[] and bdevsw[]
as empty arrays and remove all those DAMNED defines as well..
Each of these drivers has a SYSINIT linker set entry
that comes in very early.. and asks teh driver to add it's own
entry to the two devsw[] tables.
some slight reworking of the commits from yesterday (added the SYSINIT
stuff and some usually wrong but token DEVFS entries to all these
devices.
BTW does anyone know where the 'ata' entries in conf.c actually reside?
seems we don't actually have a 'ataopen() etc...
If you want to add a new device in conf.c
please make sure I know
so I can keep it up to date too..
as before, this is all dependent on #if defined(JREMOD)
(and #ifdef DEVFS in parts)
Convert the remaining sysctl stuff to the new way of doing things.
the devconf stuff is the reason for the large number of files.
Cleaned up some compiler warnings while I were there.
replacing them with TAILQ's as appropriate. The SCSI code is the
first to be changed -- until the changes are complete, both b_act and
b_actf will be in the buf structure. b_actf will eventually be removed.
sometime around 1.51, the check for minphys dissappeared out of
transfers for disks..
we weren't hecking that the adapter could handle a transfer of
the size we were requesting..
Peter!?
:)
this explains the rash of failures I've seen reported recently
with "too many DMA segments" on raw devices
(added one for st as well)
Added CONTROL device that only does user-ioctl and nothing else;
Added protection so user-ioctl requires write access;
Clean up scsiconf.h a little. It needs more work.
flags parameter to all xxstart routines so that the correct information can
be passed down into the device specific routines. This is needed to ensure
that ccb/scb allocation routines don't hang.
Submitted by: John Dyson
function calls. Broken tracking of open partitions gets fixed as a side
effect. Races in sdopen() and sdioctl() become more numerous than before.
Close the device in sdsize(). Media removal could not have worked right
when unused swap devices were held open. There may now be a problem
with used swap devices not being held open.
Fix ancient operator precedence bug in sddump(). It may have been
possible to attempt dumping to unloaded media.
Remove NetBSD ifdefs. We're too different now, and the NetBSD driver was
already too different for them to be relevant.
Remove support for soft write protection. There are no ioctls to set it,
and this driver never set it either. It was used in the wd driver to
disable writing to unlabelled disk, but we want to support writing to
foreign partitions on unlabeled disks.
Clean up some formatting and restore some old-style function headers.
sd.c: Julian's removal of subdriver requests
st.c, scsi_tape.h: Julian's suport of compressed tape drives
Note: compressed tape drives are still not working fully.
scsiconf.h, scsi_base.c, scsi_driver.c: address problems in probes
and error console logs
Reenabled "SCIOCOMAND" ioctl.
Restructured so low level drivers can easily request retries.
Added preliminary fixed SCSI devices (should be revisited before 2.1)
Added "ssc" device that can have its' (HBA, ID, LUN) set via ioctl.
device announcement; assume a sector size of 512 instead (likely to be
right at all).
This case happens when booting with a removable disk device attached
(e.g. an MOD), but no medium inserted.
and all SCSI devices (except that it's not done quite the way I want). New
information added includes:
- A text description of the device
- A ``state''---unknown, unconfigured, idle, or busy
- A generic parent device (with support in the m.i. code)
- An interrupt mask type field (which will hopefully go away) so that
. ``doconfig'' can be written
This requires a new version of the `lsdev' program as well (next commit).
