don't recurse in "make describe". The new INDEX target in
ports/Makefile invokes a perl script to recurse and convert them
into package names.
While I'm here, change the name of targets and move them around a
little bit for the sake of consistency.
It is also probably worth noting here that the meaning of the
"build dependency" list in INDEX has been changed slightly
changed. The old list was "build depends and its build depends"
-- not particularly useful if you had things like autoconf, which
run-depend on gm4 (you install all the things listed here and
you'll get an autoconf that won't run).
It is now "build depends and its run depends" -- you install
everything listed here, and you'll be able to build the port.
Submitted by: steve
(0') Fast README.html generation. It uses ports/INDEX to find
dependencies instead of embarking on to a recursive loop.
Submitted by: steve
(1) Remove NO_WRKDIR and NO_EXTRACT. Their functionality are easily
replacable with NO_WRKSUBDIR=t and EXTRACT_ONLY= (nothing on right
side), and they get in the way of read-only port trees.
(2) Surround first few variable definitions with ".if !defined()".
This will make cross-compilation easier and also speed up make
processes.
(3) Call sysctl with absolute path. Prefer the one in /sbin over the
one in /usr/sbin.
(4) Add four new variables
PKGINSTALL?= ${PKGDIR}/INSTALL
PKGDEINSTALL?= ${PKGDIR}/DEINSTALL
PKGREQ?= ${PKGDIR}/REQ
PKGMESSAGE?= ${PKGDIR}/MESSAGE
and use them in PKG_ARGS. Frobbing with PKG_ARGS directly is
strongly discouraged.
(5) Change PKG_SUFX to ".tar" (instead of ".tgz") if PKG_NOCOMPRESS is
defined. This is intended only for our own use.
(6) Add more sites to MASTER_SITE_GNU.
Submitted by: billf
(7) Override MANUAL_PACKAGE_BUILD if PARALLEL_PACKAGE_BUILD is
defined. This is intended only for our own use.
(8) Add new target "ignorelist" which will print out the package name
if the port is not going to be built on this machine. This is
intended only for our own use.
(9) Make mtree a little quieter.
incorporate some notion of which revision the device is. If it's < SCSI2, for
example, READ BLOCK LIMITS is not a MANDATORY command.
At any rate, the initial state is to try and read block limits to get a notion
of the smallest and largest record size as well as the granularity. However,
this doesn't mean that the device should actually *in* fixed block mode should
the max && min be equal... *That* choice is (for now) determined by whether
the device comes up with a blocksize of nonzero. If so, then it's a fixed block
preferred device, otherwise not (this will change again soon).
When actually doing I/O, and you're in fixed length mode, the block count is
*not* the byte count divided by the minimum block size- it's the byte count
divided by the current blocksize (or use shift/mask shortcuts if that worked
out...).
Then when you *change* the blocksize via an ioctl, make sure this actually
propagates to the stored notion of blocksize (and update the shift/mask
shortcuts).
Misc Other:
When doing a mode select, only use the SCSI_SAME_DENSITY (0x7f) code if
the device is >= SCSI2- otherwise just use the saved density code.
Recover from the ripple of ILLEGAL REQUEST not being 'retried' in that
RESERVE/RELEASE is not a mandatory command for < SCSI2 (so ignore it if it
fails).
but the present PCI probe code still thinks we are there as the pci attach
can't return an error code.
This means we are in the shared interrupt list, but have not been set up.
If we are sharing ints with another device, ohci_intr will be called and will
coredump on a NULL reference. So just return if it is called when not set up.
This fixes the symptom and not the cause.
The right answer is to let the PCI system know that the attach failed,
or to fail earlier (in the PCI probe).
The attach() is a void fn() so it can't return failure..
If we are not transfering any data, use a non S/G ccb type that doesn't
return residual information. It seems that some firmware revisions dislike
S/G ccbs with 0 length S/G lists.
Correct bt_cmd() so that we always honor command status that was latched
by our interrupt routine while polling for completion..
Remove any dial timer that might be hanging around at
datalink_Destroy() time. This timer may be left running
after the link is closed (making sure it's not automatically
opened again too soon).
exits, it causes a select() exception.
Handle these select() exceptions on link descriptors in pretty
much the same way as loss of carrier rather than dropping out
in confusion.
programs using glibc expect edx to be preserved accross syscalls.
As a result, linux programs running in emulation mode can
have whatever value may be represented by edx clobbered.
PR: 9038
Submitted-By: Richard Seaman, Jr. <dick@tar.com>
${DESTDIR}/etc and an install target to install the missing ones. This
allows new files like pam.conf to be installed by the first installworld
after the file is added, but avoid clobbering files that might be
customized. This should save some support questions.
is more robust and common code can be used for both the target and iniator
roles. The mechanism for tracking negotiation state has also been simplified.
Add support for sync/wide negotiation in target mode and fix many of
the target mode bugs running at higher speeds uncovered. Make a first
stab at getting all of the bus skew delays correct. Sync+Wide dataout
transfers still cause problems, but this may be an initiator problem.
Ensure that we exit BITBUCKET mode if the controller is restarted.
Add support for target mode only firmware downloads. This has been
tested on the aic7880, but should mean that we can perform target mode
on any aic7xxx controller. Mixed mode (initiator and target roles in
the same firmware load) is currently only supported on the aic7890, but
with optimization, may fit on chips with less instruction space.
Allow sync transfers if the controller supports it. Wide will follow
as soon as I get the kinks worked out of wide target transfers in the
aic7xxx driver (currently the only target mode driver in the tree).
to specify that it does not provide initiator services (PIM_NOINITIATOR)
and that the initial bus reset for device probing should be avoided
(PIM_NOBUSRESET).
Modify the XPT layer to honor these flags.
