Thanks to Sam for importing tags in a way that allowed this to be done.
Submitted by: Gleb Smirnoff <glebius@cell.sick.ru>
Also allow the sr and ar drivers to create netgraph versions of their modules.
Document the change to the ksocket node.
Version 3.5 brings:
- Atomic commits of ruleset changes (reduce the chance of ending up in an
inconsistent state).
- A 30% reduction in the size of state table entries.
- Source-tracking (limit number of clients and states per client).
- Sticky-address (the flexibility of round-robin with the benefits of
source-hash).
- Significant improvements to interface handling.
- and many more ...
- Remove pflog and pfsync modules. Things will change in such a fashion
that there will be one module with pf+pflog that can be loaded into
GENERIC without problems (which is what most people want). pfsync is no
longer possible as a module.
- Add multicast address for in-kernel multicast pfsync protocol. Protocol
glue will follow once the import is done.
- Add one more mbuf tag
its primary use is for the FEPS/FAS366 SCSI found in Sun Ultra 1e and 2
machines. Once the pci front-end is ported, this driver can replace the
amd(4) driver.
The code as-is is fairly stable. I've disabled tagged-queueing until I can
figure out a corruption bug related to it. I'm importing it now so that
people with these machines can (finally) stop netbooting and report bugs
before 5.3.
been developed for use with FreeBSD, version 4.8 and later.
Submitted by: Hema Joyce
Reviewed by: Prafulla Deuskar
Approved by: Prafulla Deuskar
MFC after: 1 week
- Connect geom_stripe and geom_nop modules to the build.
- Connect STRIPE and NOP classes to the LINT build.
- Disconnect gconcat(8) from the build.
Supported by: Wheel - Open Technologies - http://www.wheel.pl
hal_raise_irql(void) doesn't take an argument, but it is called with one.
eg: irql = FASTCALL1(hal_raise_irql, DISPATCH_LEVEL);
This is hidden by the macros on i386, but becomes a compile error on amd64
since the arguments are actually checked.
modules is a very nice way to produce hard-to-find panics. Who would look for
a bug in a Makefile anyway?
Has anyone seen the pointy hat? :-o
Approved by: njl (mentor)
can more easily be used INSTEAD OF the hard-working Yarrow.
The only hardware source used at this point is the one inside
the VIA C3 Nehemiah (Stepping 3 and above) CPU. More sources will
be added in due course. Contributions welcome!
stuff was here (NFS) was fixed by Alfred in November. The only remaining
consumer of the stub functions was umapfs, which is horribly horribly
broken. It has missed out on about the last 5 years worth of maintenence
that was done on nullfs (from which umapfs is derived). It needs major
work to bring it up to date with the vnode locking protocol. umapfs really
needs to find a caretaker to bring it into the 21st century.
Functions GC'ed:
vop_noislocked, vop_nolock, vop_nounlock, vop_sharedlock.
mini-layer. I don't have time to bing it forward into the GEOM world, and
no one else has stepped forward to claim it. It'll be in the Attic for safe
keeping for now.
This adds the former ports registered groups: proxy and authpf as well as
the proxy user. Make sure to run mergemaster -p in oder to complete make
installworld without errors.
This also provides the passive OS fingerprints from OpenBSD (pf.os) and an
example pf.conf.
For those who want to go without pf; it provides a NO_PF knob to make.conf.
__FreeBSD_version will be bumped soon to reflect this and to be able to
change ports accordingly.
Approved by: bms(mentor)
ethernet (tested) and FDDI (not tested). The main use for this is on ADSL (or
other ATM) connections where bridged ethernet is used, PPPoE being a prime
example.
There is no manual page as yet, I will write one shortly.
Reviewed by: harti
if_ndis.c has been split into if_ndis_pci.c and if_ndis_pccard.c.
The ndiscvt(8) utility should be able to parse device info for PCMCIA
devices now. The ndis_alloc_amem() has moved from kern_ndis.c to
if_ndis_pccard.c so that kern_ndis.c no longer depends on pccard.
NOTE: this stuff is not guaranteed to work 100% correctly yet. So
far I have been able to load/init my PCMCIA Cisco Aironet 340 card,
but it crashes in the interrupt handler. The existing support for
PCI/cardbus devices should still work as before.
along with KeInitializeTimerEx(), KeSetTimer(), KeSetTimerEx(),
KeCancelTimer(), KeReadStateTimer() and KeInitializeDpc(). I don't
know for certain that these will make the Atheros driver happy since
I don't have the card/driver combo needed to test it, but these are
fairly independent so they shouldn't break anything else.
- Debugger() is present even in kernels without options DDB, so no
conditional compilation is necessary (pointed out by bde).
- Remove the extra km_acquirecnt member that I added to struct kmutant
and embed it within an unused portion of the structure instead, so that
we don't make the structure larger than it's defined to be in Windows.
I don't know what crack I was smoking when I decided it was ok to do
this, but it's worn off now.
is set, since some drivers with debug info can be very chatty.
Also implement DbgBreakPoint(), which is the Windows equivalent of
Debugger(). Unfortunately, this forces subr_ntoskrnl.c to include
opt_ddb.h.
pf/pflog/pfsync as modules. Do not list them in NOTES or modules/Makefile
(i.e. do not connect it to any (automatic) builds - yet).
Approved by: bms(mentor)
versions of the modules, and unconditionally putting -g in CFLAGS
has negative impact on the size of the resulting .ko object, even
now that debugging symbols are always stripped.
- Unify the conditional assignments section so that architectural
exclusions come first, sorted, then options and !options, sorted
by the option name, also in directory order, then architecture
specific sections, sorted by the architecture name, with i386
being a traditional exception.
Prodded by: bde
I started with a year-old patch by Orlando Bassotto
<orlando.bassotto@ieo-research.it>, and ported it to 5.2-CURRENT along with
fixing the problems working with pre-Audigy cards.
By default, we search for files in /compat/ndis. This can be changed with
a systcl. These routines are used by some drivers which need to download
firmware or microcode into their respective devices during initialization.
Also, remove extraneous newlines from the 'built-in' sysctl/registry
variables.
of ${.TARGET}). This was the last instances of @echo in module Makefiles
after it was removed in sio/Makefile. NOMAN is nonsense in module
Makefiles, and was removed, but came back here and in too many other
places.
- SRCS was totally disordered.
- the echos to create options headers were hidden using '@'.
- the args of echos to create options headers were single-quoted.
- the target names for the rules to create options headers were repeated.
- the unused option COMPAT_FREEBSD4 was put in opt_compat.h.
(most recently bde), so I'll commit the module I've had knocking
around in my tree for a while. This may have some rough edges, so if
you are able to build it on non-i386 platform (including pc98) please
let me know you succeeded. When I get enough reports, I'll connect it
to the build. If there are problems, feel free to fix them.
Suggested by: bde
Yes, it's what you think it is. Yes, you should run away now.
This is a special compatibility module for allowing Windows NDIS
miniport network drivers to be used with FreeBSD/x86. This provides
_binary_ NDIS compatibility (not source): you can run NDIS driver
code, but you can't build it. There are three main parts:
sys/compat/ndis: the NDIS compat API, which provides binary
compatibility functions for many routines in NDIS.SYS, HAL.dll
and ntoskrnl.exe in Windows (these are the three modules that
most NDIS miniport drivers use). The compat module also contains
a small PE relocator/dynalinker which relocates the Windows .SYS
image and then patches in our native routines.
sys/dev/if_ndis: the if_ndis driver wrapper. This module makes
use of the ndis compat API and can be compiled with a specially
prepared binary image file (ndis_driver_data.h) containing the
Windows .SYS image and registry key information parsed out of the
accompanying .INF file. Once if_ndis.ko is built, it can be loaded
and unloaded just like a native FreeBSD kenrel module.
usr.sbin/ndiscvt: a special utility that converts foo.sys and foo.inf
into an ndis_driver_data.h file that can be compiled into if_ndis.o.
Contains an .inf file parser graciously provided by Matt Dodd (and
mercilessly hacked upon by me) that strips out device ID info and
registry key info from a .INF file and packages it up with a binary
image array. The ndiscvt(8) utility also does some manipulation of
the segments within the .sys file to make life easier for the kernel
loader. (Doing the manipulation here saves the kernel code from having
to move things around later, which would waste memory.)
ndiscvt is only built for the i386 arch. Only files.i386 has been
updated, and none of this is turned on in GENERIC. It should probably
work on pc98. I have no idea about amd64 or ia64 at this point.
This is still a work in progress. I estimate it's about %85 done, but
I want it under CVS control so I can track subsequent changes. It has
been tested with exactly three drivers: the LinkSys LNE100TX v4 driver
(Lne100v4.sys), the sample Intel 82559 driver from the Windows DDK
(e100bex.sys) and the Broadcom BCM43xx wireless driver (bcmwl5.sys). It
still needs to have a net80211 stuff added to it. To use it, you would
do something like this:
# cd /sys/modules/ndis
# make; make load
# cd /sys/modules/if_ndis
# ndiscvt -i /path/to/foo.inf -s /path/to/foo.sys -o ndis_driver_data.h
# make; make load
# sysctl -a | grep ndis
All registry keys are mapped to sysctl nodes. Sometimes drivers refer
to registry keys that aren't mentioned in foo.inf. If this happens,
the NDIS API module creates sysctl nodes for these keys on the fly so
you can tweak them.
An example usage of the Broadcom wireless driver would be:
# sysctl hw.ndis0.EnableAutoConnect=1
# sysctl hw.ndis0.SSID="MY_SSID"
# sysctl hw.ndis0.NetworkType=0 (0 for bss, 1 for adhoc)
# ifconfig ndis0 <my ipaddr> netmask 0xffffff00 up
Things to be done:
- get rid of debug messages
- add in ndis80211 support
- defer transmissions until after a status update with
NDIS_STATUS_CONNECTED occurs
- Create smarter lookaside list support
- Split off if_ndis_pci.c and if_ndis_pccard.c attachments
- Make sure PCMCIA support works
- Fix ndiscvt to properly parse PCMCIA device IDs from INF files
- write ndisapi.9 man page
This is the vastly updated cx drvier from Roman Kurakin <rik@cronyx.ru>
who has been patiently waiting for this update for sometime.
The driver is mostly a rewrite from the version we have in the tree.
While some similarities remain, losing the little history that the old
driver has is not a big loss, and the re@ felt it was easier this way (less
error prone).
The userland parts of this update will be committed shortly.
The driver is not connected to the build yet. I want to make sure I
don't break any platform at any time, so I want to test that with
these files in the tree before I continue (on the off chance I'm
forgetting a file).
I changed the DEBUG macro to CX_DEBUG from the code that was submitted
(to not break when we go to building with opt_global.h after the
release), as well adding $FreeBSD$.
Submitted by: Roman Kurakin
Approved by: re@ <scottl>
idx'th present CPU with pc_acpi_id equal to *acpi_id. If *acpi_id
does not match that processor's pc_acpi_id, return the value for
ProcId derived from the MADT in *acpi_id. If pc_acpi_id is 0xffffffff,
always override it with the value of *acpi_id. Finally, return
pc_cpuid in *cpu_id and use that as our primary key.
* Use pc_cpuid as our unique key because we know it is valid since
MD code set it. The values for ProcId in the ASL and MADT don't
match up on some machines (!), forcing us to fall back to ordered
probing in that case.
* Remove some #ifdef SMP since the refcount doesn't hurt performance
and will be needed for dynamic _CST objects. Only one #ifdef SMP
(for smp_rendezvous) remains.
* Hook up SMP in the compile flags in the Makefile.
Tested by: marcel, truckman
Approved by: re (scottl)
regocnized as such at the time. Now that the other bogons in the
tree have been fixed, we can remove this ugly kludge.
o Remove stale/bogus opt_foo.h files. These are left over from
by-gone resources. And they point to the need, yet again, to
improve the build system so meta information is only in one place.
Submitted by: ru
Reviewed by: bde
Approved by: re@ (jhb)
the MAC label referenced from 'struct socket' in the IPv4 and
IPv6-based protocols. This permits MAC labels to be checked during
network delivery operations without dereferencing inp->inp_socket
to get to so->so_label, which will eventually avoid our having to
grab the socket lock during delivery at the network layer.
This change introduces 'struct inpcb' as a labeled object to the
MAC Framework, along with the normal circus of entry points:
initialization, creation from socket, destruction, as well as a
delivery access control check.
For most policies, the inpcb label will simply be a cache of the
socket label, so a new protocol switch method is introduced,
pr_sosetlabel() to notify protocols that the socket layer label
has been updated so that the cache can be updated while holding
appropriate locks. Most protocols implement this using
pru_sosetlabel_null(), but IPv4/IPv6 protocols using inpcbs use
the the worker function in_pcbsosetlabel(), which calls into the
MAC Framework to perform a cache update.
Biba, LOMAC, and MLS implement these entry points, as do the stub
policy, and test policy.
Reviewed by: sam, bms
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
the nfsv4 files. It is intended to be a short-term bridge while
alfred deals with the problem in a better way (eg, don't hesitate to
back this out when the real fix comes along). I've not heard back
from alfred in a few hours and other people are hitting this problem.
Approved by: markm, rwatson, grog, murray
* Use the cpu_idle_hook() to do idling for C1-C3.
* Use both _CST and the FADT to detect Cx states.
* Use both _PTC and P_CNT for controlling throttling.
* Add a notify handler to detect changes in _CST and _PSS
* Call the _INI function for each processor if present. This will be
done by ACPI-CA in the future.
* Fix a bug on SMP systems where CPUs will attach multiple times if the
bus is rescan.
* Document new sysctls for controlling idling.
be printed, if the module were loaded into a kernel which had INET6 enabled.
The gre(4) driver does not use INET6, nor is it specified for IPv6. The
tunnel_status() function in ifconfig(8) is somewhat overzealous and assumes
that all tunnel interfaces speak KAME ifioctls.
This fix follows the path of least resistance, by teaching gre(4) about
the two KAME ifioctls concerned.
PR: bin/56341
message encoding and decoding stuff into the base module. All of this
is accessed by several of the NgATM modules and putting this into
atmbase reduceds the memory footprint.
dcons(4): very simple console and gdb port driver
dcons_crom(4): FireWire attachment
dconschat(8): User interface to dcons
Tested with: i386, i386-PAE, and sparc64.
Though this is still incomplete and has some missing features such as
exclusive login and event notification, it may be enough for someone
who wants to play with it.
This driver is supposed to work with firewire(4), targ(4) of CAM(4)
and scsi_target(8) which can be found in /usr/share/example/scsi_target.
This driver doesn't require sbp(4) which implements initiator mode.
Sample configuration:
Kernel: (you can use modules as well)
device firewire
device scbus
device targ
device sbp_targ
After reboot:
# mdconfig -a -t malloc -s 10m
md0
# scsi_target 0:0:0 /dev/md0
(Assuming sbp_targ0 on scbus0)
You should find the 10MB HDD on FreeBSD/MacOS X/WinXP or whatever connected
to the target using FireWire.
Manpage is not finished yet.
And many changes.
* all
- Major change of struct fw_xfer.
o {send,recv}.buf is splitted into hdr and payload.
o Remove unnecessary fields.
o spd is moved under send and recv.
- Remove unnecessary 'volatile' keyword.
- Add definition of rtcode and extcode.
* firewire.c
- Ignore FWDEVINVAL devices in fw_noderesolve_nodeid().
- Check the existance of the bind before call STAILQ_REMOVE().
- Fix bug in the fw_bindadd().
- Change element of struct fw_bind for simplicity.
- Check rtcode of response packet.
- Reduce split transaction timeout to 200 msec.
(100msec is the default value in the spec.)
- Set watchdog timer cycle to 10 Hz.
- Set xfer->tv just before calling fw_get_tlabel().
* fwohci.c
- Simplifies fwohci_get_plen().
* sbp.c
- Fix byte order of multibyte scsi_status informations.
- Split sbp.c and sbp.h.
- Unit number is not necessary for FIFO¤ address.
- Reduce LOGIN_DELAY and SCAN_DELAY to 1 sec.
- Add some constants defineded in SBP-2 spec.
* fwmem.c
- Introduce fwmem_strategy() and reduce memory copy.
o revamp IPv4+IPv6+bridge usage to match API changes
o remove pfil_head instances from protosw entries (no longer used)
o add locking
o bump FreeBSD version for 3rd party modules
Heavy lifting by: "Max Laier" <max@love2party.net>
Supported by: FreeBSD Foundation
Obtained from: NetBSD (bits of pfil.h and pfil.c)
from the sparc64 subtree, which breaks building non-sparc64 platforms
in the event the sparc64 subtree does not exist.
The problem is specific to the module, because non-module builds are
affected by the presence or absence of "device ebus" in the kernel
configuration.
PR: kern/56869
ethernet chips. This driver is pretty simple, however it contains
special DSP initialization code which is needed in order to get
the chip to negotiate a gigE link. (This special initialization
may not be needed in subsequent chip revs.) Also:
- Fix typo in if_rlreg.h (RL_GMEDIASTAT_1000MPS -> RL_GMEDIASTAT_1000MBPS)
- Deal with shared interrupts in re_intr(): if interface isn't up,
return.
- Fix another bug in re_gmii_writereg() (properly apply data field mask)
- Allow PHY driver to read the RL_GMEDIASTAT register via the
re_gmii_readreg() register (this is register needed to determine
real time link/media status).
written by Stuart Walsh and Duncan Barclay (with some kibbitzing by
me). I'm checking it in on Stuart's behalf.
The BCM4401 is built into several x86 laptop and desktop systems. For the
moment, I have only enabled it in the x86 kernel config because although
it's a PCI device, I haven't heard of any standalone NICs that use it. If
somebody knows of one, we can easily add it to the other arches.
This driver uses register/structure data gleaned from the Linux
driver released by Broadcom, but does not contain any of the code
from the Linux driver itself. It uses busdma.
rl(4) driver and put it in a new re(4) driver. The re(4) driver shares
the if_rlreg.h file with rl(4) but is a separate module. (Ultimately
I may change this. For now, it's convenient.)
rl(4) has been modified so that it will never attach to an 8139C+
chip, leaving it to re(4) instead. Only re(4) has the PCI IDs to
match the 8169/8169S/8110S gigE chips. if_re.c contains the same
basic code that was originally bolted onto if_rl.c, with the
following updates:
- Added support for jumbo frames. Currently, there seems to be
a limit of approximately 6200 bytes for jumbo frames on transmit.
(This was determined via experimentation.) The 8169S/8110S chips
apparently are limited to 7.5K frames on transmit. This may require
some more work, though the framework to handle jumbo frames on RX
is in place: the re_rxeof() routine will gather up frames than span
multiple 2K clusters into a single mbuf list.
- Fixed bug in re_txeof(): if we reap some of the TX buffers,
but there are still some pending, re-arm the timer before exiting
re_txeof() so that another timeout interrupt will be generated, just
in case re_start() doesn't do it for us.
- Handle the 'link state changed' interrupt
- Fix a detach bug. If re(4) is loaded as a module, and you do
tcpdump -i re0, then you do 'kldunload if_re,' the system will
panic after a few seconds. This happens because ether_ifdetach()
ends up calling the BPF detach code, which notices the interface
is in promiscuous mode and tries to switch promisc mode off while
detaching the BPF listner. This ultimately results in a call
to re_ioctl() (due to SIOCSIFFLAGS), which in turn calls re_init()
to handle the IFF_PROMISC flag change. Unfortunately, calling re_init()
here turns the chip back on and restarts the 1-second timeout loop
that drives re_tick(). By the time the timeout fires, if_re.ko
has been unloaded, which results in a call to invalid code and
blows up the system.
To fix this, I cleared the IFF_UP flag before calling ether_ifdetach(),
which stops the ioctl routine from trying to reset the chip.
- Modified comments in re_rxeof() relating to the difference in
RX descriptor status bit layout between the 8139C+ and the gigE
chips. The layout is different because the frame length field
was expanded from 12 bits to 13, and they got rid of one of the
status bits to make room.
- Add diagnostic code (re_diag()) to test for the case where a user
has installed a broken 32-bit 8169 PCI NIC in a 64-bit slot. Some
NICs have the REQ64# and ACK64# lines connected even though the
board is 32-bit only (in this case, they should be pulled high).
This fools the chip into doing 64-bit DMA transfers even though
there is no 64-bit data path. To detect this, re_diag() puts the
chip into digital loopback mode and sets the receiver to promiscuous
mode, then initiates a single 64-byte packet transmission. The
frame is echoed back to the host, and if the frame contents are
intact, we know DMA is working correctly, otherwise we complain
loudly on the console and abort the device attach. (At the moment,
I don't know of any way to work around the problem other than
physically modifying the board, so until/unless I can think of a
software workaround, this will have do to.)
- Created re(4) man page
- Modified rlphy.c to allow re(4) to attach as well as rl(4).
Note that this code works for the sample 8169/Marvell 88E1000 NIC
that I have, but probably won't work for the 8169S/8110S chips.
RealTek has sent me some sample NICs, but they haven't arrived yet.
I will probably need to add an rlgphy driver to handle the on-board
PHY in the 8169S/8110S (it needs special DSP initialization).
FIDs to be 128-bits wide and adds support for realms.
Add a new CODA_COMPAT_5 option, which requests support for the old
Coda 5.x interface instead of the new one.
Create a new coda5.ko module that supports the 5.x interface, and make
the existing coda.ko module use the new 6.x interface. These modules
cannot both be loaded at the same time.
Obtained from: Jan Harkes & the coda-6.0.2 distribution,
NetBSD (drochner) (CODA_COMPAT_5 option).
of what uart(4) is and/or is not see the initial commit log of one
of the files in sys/dev/uart (or see share/man/man4/uart.4).
Note that currently pc98 shares the MD file with i386. This needs
to change when pc98 support is fleshed-out to properly support the
various UARTs. A good example is sparc64 in this respect.
We build uart(4) as a module on all platforms. This may break
the ppc port. That depends on whether they do actually build
modules.
To use uart(4) on alpha, one must use the NO_SIO option.
change also disables interrupts around non-S4 suspends whereas before we
did not do this. Our version of AcpiEnterSleepStateS4bios was almost
identical to the ACPICA version.
support stripped out and minimally renamed to owi. This driver
attaches to lucent cards only. This is designed to aid in the testing
of fixes to the wi driver for lucent cards. It is supported only as a
module (you cannot compile it into your kernel). You cannot have the
wi driver in your kernel (or loaded as a moudle) to use the owi
module.
I've not connected it to build, as this module is currently for
debugging purposes. This is for developers only at the present time.
If we can't get lucent support fixed by 5.2 code freeze, then we'll
re-evaulate this support level. Please use this to fix the lucent
support in dev/wi. This will be removed from the system when lucent
support has been fixed in dev/wi.
Note to developers: Do not connect this to the build, make it possible
to build into the kernel or otherwise 'integrate' this into system
without checking with me first. This is for debugging purposes only.
If this doesn't work for you, I don't want to hear about it unless you
are fixing the wi driver :-)
found only many tv-cards.
We currently use more ore less evil hacks (slow_msp_audio sysctl) to
configure the various variants of these chips in order to have
stereo autodetection work. Nevertheless, this doesn't always work
even though it _should_, according to the specs.
This is, for example, the case for some popular Hauppauge models sold
sold in Germany.
However, the Linux driver always worked for me and others. Looking at
the sourcecode you will find that the linux-driver uses a very much
enhanced approach to program the various msp34xx chipset variants,
which is also found in the specs for these chips.
This is a port of the Linux MSP34xx code, written by Gerd Knorr
<kraxel@bytesex.org>, who agreed to re-release his code under a
BSD license for this port.
A new config option "BKTR_NEW_MSP34XX_DRIVER" is added, which is required
to enable the new driver. Otherwise the old code is used.
The msp34xx.c file is diff-reduced to the linux-driver to make later
modifications easier, thus it doesn't follow style(9) in most cases.
Approved by: roger (committing this, no time to test/review),
keichii (code review)
it attaches to all existing NATM network interfaces in the system
and creates a HARP physical interface for each of them. This allows
us to use the same set of ATM drivers for all ATM stuff. It is
possible to use the same interface for HARP, NATM and netgraph at the
same time.
with a ProATM-155 and an IDT evaluation board and should also work
with a ProATM-25 (it seems to work at least, I cannot really measure
what the card emits). The driver has been tested on i386 and sparc64,
but should work an other archs also. It supports UBR, CBR, ABR and VBR;
AAL0, AAL5 and AALraw. As an additional feature VCI/VPI 0/0 can be
opened for receiving in AALraw mode and receives all cells not claimed
by other open VCs (even cells with invalid GFC, VPI and VCI fields and
OAM cells).
Thanks to Christian Bucari from ProSum for lending two cards and answering
my questions.
large to huge amounts of small or medium sized receive buffers. The problem
with these situations is that they eat up the available DMA address space
very quickly when using mbufs or even mbuf clusters. Additionally this
facility provides a direct mapping between 32-bit integers and these buffers.
This is needed for devices originally designed for 32-bit systems. Ususally
the virtual address of the buffer is used as a handle to find the buffer as
soon as it is returned by the card. This does not work for 64-bit machines
and hence this mapping is needed.
ACPI nodes with the plug and play ID's defined for a "Generic ISA Bus
Device" as defined in section 10.7 of the ACPI 2.0 specification. This
gives machines like the Libretto that contain a fake ISA bus that is not
connected via a PCI-ISA bridge an ISA bus for ISA devices to attach to.
Tested by: markm
This is based on the ubsa driver by Alexander Kabaev along with documentation
gleaned from the Linux mct_u232 driver. I've had this driver sitting in my
tree for almost 6 months, and several others have found it useful.
build it on the i386 and alpha architectures, where this has been
set up (there is also a sparc64-bitops.h in sys/gnu/ext2fs, but it
appears to be broken and it is not linked up).
This should unbreak the sparc64 LINT build.
built by LINT. Also override a number of knobs for enabling and
disabling various modules in the ALL_MODULES case to further increase
LINT's module coverage.
Submitted by: ru
redundant paths to the same device.
This class reacts to a label in the first sector of the device,
which is created the following way:
# "0123456789abcdef012345..."
# "<----magic-----><-id-...>
echo "GEOM::FOX someid" | dd of=/dev/da0 conv=sync
NB: Since the fact that multiple disk devices are in fact the same
device is not known to GEOM, the geom taste/spoil process cannot
fully catch all corner cases and this module can therefore be
confused if you do the right wrong things.
NB: The disk level drivers need to do the right thing for this to
be useful, and that is not by definition currently the case.
on friday 13th and without making a universe). This adds struct and
constant definitions for ATM traffic parameters and re-enables the
build of the midway driver.
Tested by: make universe
from the tree until it is fixed. Since it is an atm driver, it isn't
commonly used so this will not negatively impact too many people.
harti can reconnect it when he resurfaces and corrects the en module
problems. This should allow snapshots to start succeeding again.
Reported by: lots of people
It currently supports the PMC Sierra Lite, Ultra and 622 chips and
the IDT 77105. The driver handles media options and state in a consistent
manner for ATM drivers. The next commit to the midway driver will make
it use utopia.
series. This driver was generously developed and released by David
Jeffreys and Adaptec. I've updated it to work with 5.x and fixed a
few bugs.
MFC After: 1 week
* AcpiOsDerivePciId(): finds a bus number, given the slot/func and the
acpi parse tree.
* AcpiOsPredefinedOverride(): use the sysctl hw.acpi.os_name to
override the value for _OS.
Ideas from: takawata, jhb
Reviewed by: takawata, marcel
Tested on: i386, ia64
following changes have been done:
- stylify. The original code was too hard to read.
- get rid of a number of compilation options (Adaptec-only, Eni-only, no-DMA).
- more debugging features.
- locking. This is not correct yet in the absence of interface layer locking,
but is correct enough to not to cause lock order reversals.
- remove RAW mode. There are no users of this in the tree and I doubt that
there are any.
- remove NetBSD compatibility code. There was no way to keep NetBSD non-busdma
and FreeBSD busdma code together.
- if_en now buildable as a module.
This has been actively tested on sparc64 and i386 with ENI server and
client cards and an Adaptec card (thanks to kjc).
Reviewed by: mdodd, arr
ethernet controller. The driver has been tested with the LinkSys
USB200M adapter. I know for a fact that there are other devices out
there with this chip but don't have all the USB vendor/device IDs.
Note: I'm not sure if this will force the driver to end up in the
install kernel image or not. Special magic needs to be done to exclude
it to keep the boot floppies from bloating again, someone please
advise.
Many internal structure changes for the FireWire driver.
- Compute CRC in CROM parsing.
- Add support for configuration ROM build.
- Simplify dummy buffer handling.
- busdma conversion
- Use swi_taskqueue_giant for -current. Mark the interrupt routine as MPSAFE.
- AR buffer handling.
Don't reallocate AR buffer but just recycle it.
Don't malloc and copy per packet in fwohci_arcv().
Pass packet to fw_rcv() using iovec.
Application must prepare receiving buffer in advance.
- Change fw_bind API so that application should pre-allocate xfer structure.
- Add fw_xfer_unload() for recycling struct fw_xfer.
- Add post_busreset hook
- Remove unused 'sub' and 'act_type' in struct fw_xfer.
- Remove npacket from struct fw_bulkxfer.
- Don't call back handlers in fwochi_arcv() if the packet has
not drained in AT queue
- Make firewire works on big endian platform.
- Use native endian for packet header and remove unnecessary ntohX/htonX.
- Remove FWXFERQ_PACKET mode. We don't use it anymore.
- Remove unnecessary restriction of FWSTMAXCHUNK.
- Don't set root node for phy config packet if the root node is
not cycle master capable but set myself for root node.
We should be the root node after next bus reset.
Spotted by: Yoshihiro Tabira <tabira@scd.mei.co.jp>
- Improve self id handling
Tested on: i386, sparc64 and i386 with forced bounce buffer
monitors the entropy data harvested by crypto drivers to verify it complies
with FIPS 140-2. If data fails any test then the driver discards it and
commences continuous testing of harvested data until it is deemed ok.
Results are collected in a statistics block and, optionally, reported on
the console. In normal use the overhead associated with this driver is
not noticeable.
Note that drivers must (currently) be compiled specially to enable use.
Obtained from: original code by Jason L. Wright
included in XFree86 4.3, but includes some fixes. Notable changes include
Radeon 8500-9100 support, PCI Radeon/Rage 128 support, transform & lighting
support for Radeons, and vblank syncing support for r128, radeon, and mga.
The gamma driver was removed due to lack of any users.
permit users and groups to bind ports for TCP or UDP, and is intended
to be combined with the recently committed support for
net.inet.ip.portrange.reservedhigh. The policy is twiddled using
sysctl(8). To use this module, you will need to compile in MAC
support, and probably set reservedhigh to 0, then twiddle
security.mac.portacl.rules to set things as desired. This policy
module only restricts ports explicitly bound using bind(), not
implicitly bound ports where the port number is selected by the
IP stack. It appears to work properly in my local configuration,
but needs more broad testing.
A sample policy might be:
# sysctl security.mac.portacl.rules="uid:425:tcp:80,uid:425:tcp:79"
This permits uid 425 to bind TCP sockets to ports 79 and 80. Currently
no distinction is made for incoming vs. outgoing ports with TCP,
although that would probably be easy to add.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
turns runs its tasks free of Giant too. It is intended that as drivers
become locked down, they will move out of the old, Giant-bound taskqueue
and into this new one. The old taskqueue has been renamed to
taskqueue_swi_giant, and the new one keeps the name taskqueue_swi.
time and there's no indication that it will improve anytime soon.
By removing support for SimOS it is possible to build LINT on
Alpha, which is considered more important at the moment.
Not objected to on: alpha@
for the agp module, and add agp to the list of modules to compile for alpha.
Add an alpha_mb() to agp_flush_cache for alpha -- it's not correct but may
improve the situation, and it's what linux and NetBSD do.
we have the rc4 code already in the kernel (via wlan stuff or awi).
Add a dependency on the rc4 module so if it doesn't exist then load it.
Reviewed by: archie
IP fast forwarding, SIOCGIFADDR, setting hardware address (not currently
enabled in cm driver), multicasts (experimental)
- add ARC_MAX_DATA, use IF_HANDOFF, remove arc_sprintf() and some unused
variables
- if_simloop logic is made more similar to ethernet
- drop not ours packets early (if we are not in promiscous mode)
Submitted by: mark tinguely (partially)
Interface (SMAPI) BIOS, which is present on some IBM
Thinkpad models (560, 600, 770 to name a few.)
The SMAPI BIOS provides access to System Information,
System Configuration, and Power Management.
- Separate fc->dev (i.e. fwohci0) and fc->bdev (i.e. firewire0).
- Remove unused firewirebusreg.h.
- Reduce size of descriptor block for asynchronous transmit and
check the number of descriptor when copying from mbuf.
- Skip mbuf whose length is zero. NFS seems passing such mbuf and
some chips generates unrecoverable error.
module dependency system rely on linker behaviour that is machine dependent
and not part of the elf spec, and only work by accident on other platforms.
Approved by: re
the supported platforms. We build it into GENERIC, and it is currently
listed on the supported module list for drivers.conf on i386, which
breaks the release build. This may fix the release build for RC1 on
i386.
Conspiracy of: re
This code allows a user program to enable target mode on a SIM and
then emulate any number of devices (disks, tape drives, etc.) All
decisions about device behavior (UA, CA, inquiry response) are left
to the usermode program and the kernel driver is merely a conduit
for CCBs. This enables multiple concurrent target emulators, each
using its own backing store and IO model.
Also included is a user program that emulates a disk (RBC) using a
file as a backing store. This provides functionality similar to
md(4) at the CAM layer.
Code has been tested on ahc(4) and should also work on isp(4) (and
other SIMs that gain target mode support). It is a complete rewrite
of /sys/cam/scsi_target* and /usr/share/examples/scsi_target.
Design, comments from: gibbs
Supported by: Cryptography Research
Approved by: re
These makefiles work when building in the sys/modules directory, but
not with the objdir stuff that buildkernel uses. This is because they
used -I../../../blah rather than -I${.CURDIR}/../../../blah.
# I didn't fix the abuse of CFLAGS to specify -g since I wanted the
# barest minimal change since we're in a code freeze.
Approved by: make buildkernel...
Hat for armchair anarchists: core member fixing src tree damage
Has been seen to work on several cards and communicating with
several mobile phones to use them as modems etc.
We are still talking with 3com to try get them to allow us to include
the firmware for their pccard in the driver but the driver is here..
In the mean time
it can be downloaded from the 3com website and loaded using the utility
bt3cfw(8) (supplied) (instructions in the man page)
Not yet linked to the build
Submitted by: Maksim Yevmenkin <myevmenk@exodus.net>
Approved by: re
system accounting configuration and for nfsd server thread attach.
Policies might use this to protect the integrity or confidentiality
of accounting data, limit the ability to turn on or off accounting,
as well as to prevent inappropriately labeled threads from becoming nfs
server threads.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
is a compiler tool and needs to be compiled by the host compiler. I've
tested this in i386->sparc cross-build, 4.7->current upgrade, normal
buildkernel target, and normal /sys/i386/compile/GENERIC configurations.
Submitted by: ru
This is NOT YET CONVERTED TO -current.
This node is a source for preprogrammed packets at a known rate for testing.
I will convert it to -current "in place" but will MFC teh original
pre-conversion variant as that is what is originally submitted.
Man page my me, info from Dave's README.
Submitted by: Dave Chapeskie <dchapeskie@SANDVINE.com>
Obtained from: Sandvine inc.
MFC after: 1 week
These are really only partly netgraph nodes as they do not use the
netgraph interfaces for many of the functions for which they could
be used, however they represent important functionality.
Submitted by: wpaul
MFC after: 2 days
"refreshing" the label on the vnode before use, just get the label
right from inception. For single-label file systems, set the label
in the generic VFS getnewvnode() code; for multi-label file systems,
leave the labeling up to the file system. With UFS1/2, this means
reading the extended attribute during vfs_vget() as the inode is
pulled off disk, rather than hitting the extended attributes
frequently during operations later, improving performance. This
also corrects sematics for shared vnode locks, which were not
previously present in the system. This chances the cache
coherrency properties WRT out-of-band access to label data, but in
an acceptable form. With UFS1, there is a small race condition
during automatic extended attribute start -- this is not present
with UFS2, and occurs because EAs aren't available at vnode
inception. We'll introduce a work around for this shortly.
Approved by: re
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
This policy can be loaded dynamically, and assigns each process a
partition number, as well as permitting processes to operate outside
the partition. Processes contained in a partition can only "see"
processes inside the same partition, so it's a little like jail.
The partition of a user can be set using the label mechanisms in
login.conf. This sample policy is a good starting point for developers
wanting to learn about how to produce labeled policies, as it labels
only one kernel object, the process credential.
PR:
Submitted by:
Reviewed by:
Approved by:
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
- Add detach support to the driver so that you can kldunload the module.
Note that currently rc_detach() fails to detach a unit if any of its
child devices are open, thus a kldunload will fail if any of the tty
devices are currently open.
- sys/i386/isa/ic/cd180.h was moved to sys/dev/ic/cd180.h as part of
this change.
Requested by: rwatson
Tested by: rwatson
changes for "LSILogic"
(2) enabled non-disk support through CAM interface
(3) HA_INQ (a) enabled tagged queuing (b) disable reset during
driver loading (b) renamed BSDi string to LSI
(4) disabled detecting disk devices during SCSI INQUIRY
(5) changed dcdb single element sglist to send one entire buffer chunk
(6) nsgelem not set in sglist
(7) ap_data_transfer_length not set for dcdb
(8) changed "struct thread" to "d_thread_t" for compatibliity { xxx_open,
xxx_close, xxx_ioctl }
(9) miscellaneous compatiblity fixes
(10) bug fix for 0x0409/0x1000 card
(11) added compiling amr_cam.c in sys/conf/files
(12) added compiling amr_cam.c in sys/modules/amr/Makefile
Reviewed by:ps
MFC after:1 week
1 week
This allocate the best IRQ to boot-disable devices (have IRQ 0).
Allocated IRQ will be used for PCI interrupt routing when ACPI is
enabled.
Note that verbose messaging enabled for the time being so that
people can easily notice the strange behavior if it happened.
aac driver dependent on the linux emulation module. This was
especially bad for the release engineers who tried to move the
aac driver from the kernel onto the drivers floppy. The linux
compat bits for this driver are now in their own driver, aac_linux.
It can be loaded as a module or compiled into the kernel. For
the latter case, the AAC_COMPAT_LINUX option is needed, along with
the COMPAT_LINUX option.
I've tested this in every configuration I can think of. This is an
MFC candidate for 4.7.
Idea from: rwatson
MFC after: 3 days
