an URB before sending ZLP) set to the default. Choosing a bad value
can apparently cause a lockup on some machines/controllers.
Reported by: Doug Ambrisko
93cx6.c:
Make the SRAM dump output a little prettier.
aic7xxx.c:
Store all SG entries into our SG array in kernel space.
This makes data-overrun and other error reporting more
useful as we can dump all SG entries. In the past,
we only stored the SG entries that the sequencer might
need to access, which meant we skipped the first element
that is embedded into the SCB.
Add a table of chip strings and replace ugly switch
statements with table lookups.
Add a table with bus phase strings and message reponses
to parity errors in those phases. Use the table to
pretty print bus phase messages as well as collapse
another switch statement.
Fix a bug in target mode that could cause us to unpause
the sequencer early in bus reset processing.
Add the 80MHz/DT mode into our syncrate table. This
rate is not yet used or enabled.
Correct some comments, clean up some code...
aic7xxx.h:
Add U160 controller feature information.
Add some more bit fields for various SEEPROM formats.
aic7xxx.reg:
Add U160 register and register bit definitions.
aic7xxx.seq:
Make phasemis state tracking more straight forward. This
avoids the consumption of SINDEX which is a very useful register.
For the U160 chips, you must use the 'mov' instruction to
update DFCNTRL. Using 'or' to set the PRELOADED bit is
completely ineffective.
At the end of the command phase, wair for our ACK signal
to de-assert before disabling the SCSI dma engine. For
slow devices, this avoids clearing the ACK before the
other end has had a chance to see it and lower REQ.
controllers will run at U2 speeds until I can complete the U160 support
for this driver.
Correct a termination buglet for the 2940UW-Pro.
Be more paranoid in how we probe and enable external ram, fast external
ram timing and external ram parity checking. We should now work on
20ns and 8bit SRAM parts.
Perform initial setup for the DT feature on cards that support it.
Factorize and clean up code. Use tables where it makes sense, etc.
Add some delays in dealing with the board control logic. I've never
seen this code fail, but with the ever increasing speed of processors,
its better to insert deterministic delays just to be safe. This stuff
is only touched during probe and attach, so the extra delay is of no
concern.
ethernet adapters that are supported by the aue and kue drivers.
There are actually a couple more out there from Accton, Asante and
EXP Computer, however I was not able to find any Windows device
drivers for these on their servers, and hence could not harvest
their vendor/device ID info. If somebody has one of these things
and can look in the .inf file that comes with the Windows driver,
I'd appreciate knowing what it says for 'VID' and 'PID.'
Additional adapters include: the D-Link DSB-650 and DSB-650TX, the
SMC 2102USB, 2104USB and 2202USB, the ATen UC10T, and the Netgear EA101.
These are all mentioned in the man pages, relnotes and LINT.
Also correct the date in the kue(4) man page. I wrote this thing
on Jan, 4 2000, not 1999.
. add Xrs to hosts.equiv(5), auth.conf(5), services(5) to some pages
. sort Xrs in SEE ALSO sections
Patches based on PR: docs/15680
Submitted by: Christian Weisgerber <naddy@mips.rhein-neckar.de>
* Add the 'h' ftp flag (allocate local port in high range)
* Add the 'd' flag (use direct connection even if proxy is defined)
* Make sure flags != NULL before calling strchr().
* Minor changes to some comments.
only when either of sflag and "-f inet6" is specified.
-fix the indentation of default output
Specified by: Stephen McKay <syssgm@detir.qld.gov.au>
Reviewed and Confirmed by: Stephen McKay <syssgm@detir.qld.gov.au>
