Commit Graph

491 Commits

Author SHA1 Message Date
Matt Jacob
70e9673917 Disable RIO (reduced interrupt operation) for 2200 boards- it seemed like
it worked- but I ran into a case with a 2204 where commands were being lost
right and left. Best be safe.

For target mode, or things called if we call isp_handle_other response- note
that we might have dropped locks by changing the output pointer so we bail
from the loop. It's the responsibility of the entity dropping the lock to
make sure that we let the f/w know we've read thus far into the response
queue (else we begin processing the same entries again- blech!).

MFC after:	1 day
2002-03-07 17:32:45 +00:00
Matt Jacob
f553351ed2 Reorder some of the ioctls and add a few new ones.
MFC after:	1 day
2002-02-21 23:30:05 +00:00
Matt Jacob
014e78d18c Fix a problem where a local loop disk logs out- and we get a PORT LOGGED
OUT status. We are, apparently, required to force the f/w to log back in
if we want to try and talk to that disk again. This means either issuing
a LOGIN LOCAL LOOP PORT mailbox command, or by issuing a LIP. I've elected
to issue a LIP because this has a better chance of waking up the disk which
clearly just crashed and burned.

These should not occur at all. If they do, they should be darned rare.

MFC after:	1 week
2002-02-21 01:56:08 +00:00
Matt Jacob
d134aa0b20 More for f/w crash dumps (bug fixing and adding ioctl entry points
and hints to enable for specific units)

MFC after:	1 week
2002-02-18 00:00:34 +00:00
Matt Jacob
b894188248 Support for f/w crash dumps (2200 && 23XX).
If you want QLogic to look at a potential f/w problem for FC cards, you really
have to provide them info in the format they expect. This involves dumping
a lot of hardware registers (> 300 16 bit registers) and a lot of SRAM
(> 128KB minimum). Thus all of this code is #ifdef protected which will
become an option so that the memory allocation of where to dump the crash
image is pretty expensive. It's worth it if you have a reproducible problem
because they have some tools that can tell them, given the f/w version,
the precise state of everything.

MFC after:	1 week
2002-02-17 06:38:22 +00:00
Matt Jacob
3f02619fb8 Hints for WWN are now WWNN and/or WWPN.
MFC after:	1 week
2002-02-17 06:34:21 +00:00
Matt Jacob
01ff579d86 Add in support firmware crash dumps. Change CFG options to split
WWN into WWNN and WWPN.

MFC after:	1 week
2002-02-17 06:32:58 +00:00
Matt Jacob
75c1e828c0 + A variety of 23XX changes:
disable MWI on 2300

	based on function code, set an 'isp_port' for the 2312- it's a
	separate instance, but the NVRAM is shared, and the second port's
	NVRAM is at offset 256.

+ Enable RIO operation for LVD SCSI cards. This makes a *big* difference
as even under reasonable load we get batched completions of about 30
commands at a time on, say, an ISP1080.

+ Do 'continuation' mailbox commands- this allows us to specify a work
area within the softc and 'continue' repeated mailbox commands. This is
more or less on an ad hoc basis and is currently only used for firmware
loading (which f/w now loads substantially faster becuase the calling
thread is only woken when all the f/w words are loaded- not for each
one of the 40000 f/w words that gets loaded).

+ If we're about to return from isp_intr with a 'bogus interrupt' indication,
and we're not a 23XX card, check to see whether the semaphore register is
currently *2* (not *1* as it should be) and whether there's an async completion
sitting in outgoing mailbox0. This seems to capture cases of lost fast posting
and RIO interrupts that the 12160 && 1080 have been known to pump out under
extreme load (extreme, as in > 250 active commands).

+ FC_SCRATCH_ACQUIRE/FC_SCRATCH_RELEASE macros.

+ Endian correct swizzle/unswizzle of an ATIO2 that has a WWPN in it.

MFC after:	1 week
2002-02-04 21:04:25 +00:00
Matt Jacob
975284da32 Add missing move of relative offset for CTIO2 updates. 2002-01-11 23:48:25 +00:00
Matt Jacob
2903b27203 Implement REDUCED INTERRUPT OPERATION usage form FC cards- this allows the
firmware to delay completion of commands so that it can attempt to batch
a bunch of completions at once- either returning 16 bit handles in mailbox
registers, or in a resposne queue entry that has a whole wad of 16 bit handles.

Distinguish between 2300 and 2312 chipsets- if only because the revisions
on the chips have different meanings.

Add more instrumentation plus ISP_GET_STATS and ISP_CLR_STATS ioctls.
Run up the maximum number of response queue entities we'll look at
per interrupt.

If we haven't set HBA role yet, always return success from isp_fc_runstate.

MFC after:	2 weeks
2002-01-03 20:43:22 +00:00
Matt Jacob
c748b5e634 Explicitly decode GetAllNext SNS Response back *as*
a GetAllNext response. Otherwise, we won't unswizzle
it correctly. This was found on linux/PPC.

This mandated creating another inline: isp_get_gan_response.
2001-12-11 21:58:04 +00:00
Matt Jacob
4fd13c1ba2 Major restructuring for swizzling to the request queue and unswizzling from
the response queue. Instead of the ad hoc ISP_SWIZZLE_REQUEST, we now have
a complete set of inline functions in isp_inline.h. Each platform is
responsible for providing just one of a set of ISP_IOX_{GET,PUT}{8,16,32}
macros.

The reason this needs to be done is that we need to have a single set of
functions that will work correctly on multiple architectures for both little
and big endian machines. It also needs to work correctly in the case that
we have the request or response queues in memory that has to be treated
specially (e.g., have ddi_dma_sync called on it for Solaris after we update
it or before we read from it). It also has to handle the SBus cards (for
platforms that have them) which, while on a Big Endian machine, do *not*
require *most* of the request/response queue entry fields to be swizzled
or unswizzled.

One thing that falls out of this is that we no longer build requests in the
request queue itself. Instead, we build the request locally (e.g., on the
stack) and then as part of the swizzling operation, copy it to the request
queue entry we've allocated. I thought long and hard about whether this was
too expensive a change to make as it in a lot of cases requires an extra
copy. On balance, the flexbility is worth it. With any luck, the entry that
we build locally stays in a processor writeback cache (after all, it's only
64 bytes) so that the cost of actually flushing it to the memory area that is
the shared queue with the PCI device is not all that expensive. We may examine
this again and try to get clever in the future to try and avoid copies.

Another change that falls out of this is that MEMORYBARRIER should be taken
a lot more seriously. The macro ISP_ADD_REQUEST does a MEMORYBARRIER on the
entry being added. But there had been many other places this had been missing.
It's now very important that it be done.

Additional changes:

Fix a longstanding buglet of sorts. When we get an entry via isp_getrqentry,
the iptr value that gets returned is the value we intend to eventually plug
into the ISP registers as the entry *one past* the last one we've written-
*not* the current entry we're updating. All along we've been calling sync
functions on the wrong index value. Argh. The 'fix' here is to rename all
'iptr' variables as 'nxti' to remember that this is the 'next' pointer-
not the current pointer.

Devote a single bit to mboxbsy- and set aside bits for output mbox registers
that we need to pick up- we can have at least one command which does not
have any defined output registers (MBOX_EXECUTE_FIRMWARE).

MFC after:	2 weeks
2001-12-11 00:18:45 +00:00
Matt Jacob
fc16d270b7 Tra-La, another QLogic f/w funny- this time with the 2300.
If we get a completion status of RQCS_QUEUE_FULL, it means
that the internal queues are full. Other QLogic boards set
the QFULL SCSI status. But *nooooooooooo*, not the 2300.

MFC after:	1 day
2001-10-23 23:05:20 +00:00
Matt Jacob
8b8e73049d Protect against deranged fabric nameservers that spit out 10000 identical
port numbers.

MFC after:	1 day
2001-10-18 17:26:52 +00:00
Matt Jacob
1c3749836f Add some somewhat vague documentation for this driver and a list
of Hardware that might, in fact, work.
2001-10-07 18:26:47 +00:00
Matt Jacob
71793c0dc4 Some patches from Doug for ia64 support- the principle one being the
appropriate cache flush that provides MEMORY_BARRIER in between handoffs
between host && RISC processor for the shared memory request/response
queues.

Submitted by:	dfr@nlsystems.com
2001-10-07 18:18:50 +00:00
Matt Jacob
cd37f56f5a Misunderstanding documentation caused me to try and set 1Gbps/2Gps/Auto
connection speed for the 2300 in the wrong offset in the ICB. Oops.

Respect some QLogic errat wrt PCI errors on certain shared host/RISC registers.
2001-10-06 20:41:18 +00:00
Matt Jacob
3bd4033010 Whups- remember to zero the isr pointer arg. 2001-10-06 19:34:43 +00:00
Matt Jacob
db4fa023f8 Respect QLogic's errata- read BIU_ISR even on the 2300
to see if there's an interrupt (avoids PCI parity errors
which can occur on the 2312 if you access some registers
from the host at the same time the RISC on the 2312 is
C accessing them).

MFC after:	1 day
2001-10-06 19:19:24 +00:00
Matt Jacob
53036e9289 Begin to implement target mode that for Fibre Channel has a private
per-command component that we *don't* try and pass thru CAM. CAM just
is too risky and too much of a pain- structures get copied, but not
all info of interest can be considered safely transported thru all
consumers (including user space) from the incoming ATIO to the outgoing
CTIO- it's just much safer to have a buddy structure, identified by the
command's tag which *does* make it thru safely.

Pay attention to link speed and report 200MB/s xfer speed for a
23XX card in 2GPs mode.

MFC after:	1 week
2001-10-01 03:48:42 +00:00
Matt Jacob
c507669af4 Implement a call to get the actual link data rate (if 23XX) so we can
set whether it's a 2Gps or 1Gps link.

MFC after:	1 week
2001-10-01 03:45:54 +00:00
Matt Jacob
83548830a7 When calling isp_reset, set the request/response in/out pointers all at
once so there isn't a window with the ones for the 23XX cards being wrong.

When being verbose, print out some more FC NVRAM values (like framesize).

MFC after:	1 week
2001-09-29 19:37:49 +00:00
Julian Elischer
b40ce4165d KSE Milestone 2
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.

Sorry john! (your next MFC will be a doosie!)

Reviewed by: peter@freebsd.org, dillon@freebsd.org

X-MFC after:    ha ha ha ha
2001-09-12 08:38:13 +00:00
Matt Jacob
64edff948b I don't know what I was thinking- if I have two separate busses on on
SIM (as is true for the 1280 and the 12160), then I have to have separate
flags && status for *both* busses. *Whap*.

Implement condition variables for coordination with some target mode
events. It's nice to use these and not panic in obscure little places
in the kernel like 'propagate_priority' just because we went to sleep
holding a mutex, or some other absurd thing.

Remove some bogus ISP_UNLOCK calls. *Whap*.

No longer require that somebody do a lun enable on the wildcard device
to enable target mode. They are, in fact, orthogonal. A wildcard open
is a statement that somebody upstream is willing to accept commands which
are otherwise unrouteable. Now, for QLogic regular SCSI target mode, this
won't matter for a damn because we'll never see ATIOs for luns we haven't
enabled (are listening for, if you will). But for SCCLUN fibre channel
SCSI, we get all kinds of ATIOs. We can either reflect them back here
with minimal info (which is isp_target.c:isp_endcmd() is for), or the
wildcard device (nominally targbh) can handle them.

Do further checking against firmware attributes to see whether we can,
in fact, support target mode in Fibre Channel. For now, require SCCLUN
f/w to supoprt FC target mode.

This is an awful lot of change, but target mode *still* isn't quite right.

MFC after:	4 weeks
2001-09-04 21:53:12 +00:00
Matt Jacob
23ac1fce7b Note for ATIOs returned because of BDRs or Bus Resets for which bus this
applies to.  Do more bus # foo things.

Acknowledge Immediate Notifies right away prior to throwing events upstream
(where they're currently being ignored, *groan*)

Capture ASYNC_LIP_F8 as with ASYNC_LIP_OCCURRED. Don't percolate them
upstream as if they were BUS RESETS- they're not.
2001-09-04 21:48:02 +00:00
Matt Jacob
b96934e89a If we're on an interrupt stack, mark things so that we don't try
and cv_wait for mailbox commands to complete if we start them from
here.

Fix residuals for target mode such that we only check the residual and
set it in the CTIO if this is the last CTIO (when we're sending status).

MFC after:	4 weeks
2001-09-04 21:45:57 +00:00
Matt Jacob
f6a3bcf86c I don't know what I was thinking- if I have two separate busses on on
SIM (as is true for the 1280 and the 12160), then I have to have separate
flags && status for *both* busses. *Whap*.

Implement condition variables for coordination with some target mode
events. It's nice to use these and not panic in obscure little places
in the kernel like 'propagate_priority' just because we went to sleep
holding a mutex, or some other absurd thing.

MFC after:	4 weeks
2001-09-04 21:33:06 +00:00
Matt Jacob
2332ac8c61 Fix SET_IID_VAL/SET_BUS_VAL macros to usable.
MFC after:	4 weeks
2001-09-04 19:42:13 +00:00
Matt Jacob
d82b6503a9 Because we now store SCCLUN capabilities in firmware attributes, get
rid of the silly test of isp_maxluns > 16 and use the attibutes directly.

MFC after:	4 weeks
2001-09-03 03:12:10 +00:00
Matt Jacob
181640a81c Clarify issues about whether we have SCCLUN (65535 luns) or non-SCCLUN (16
luns) firmware for the Fibre Channel cards.

We used to assume that if we didn't download firmware, we couldn't know
what the firmware capability with respect to SCCLUNs is- and it's important
because the lun field changes in the request queue entry based upon which
firmware it is.

At any rate, we *do* get back firmware attributes in mailbox register 6
when we do ABOUT FIRMWARE for all 2200/2300 cards- and for 2100 cards
with at least 1.17.0 firmware. So- we now assume non-SCCLUN behaviour
for 2100 cards with firmware < 1.17.0- and we check the firmware attributes
for other cards (loaded firmware or not).

This also allows us to get rid of the crappy test of isp_maxluns > 16-
we simply can check firmware attributes for SCCLUN behaviour.

This required an 'oops' fix to the outgoing mailbox count field for
ABOUT FIRMWARE for FC cards.

Also- while here, hardwire firmware revisions for loaded code for SBus
cards. Apparently the 1.35 or 1.37 f/w we've been loading into isp1000
just doesn't report firmware revisions out to mailbox regs 1, 2 and 3
like everyone else. Grumble. Not that this fix hardly matters for FreeBSD.

MFC after:	4 weeks
2001-09-03 03:09:48 +00:00
Matt Jacob
f8597b62e5 Add some more firmware revision macros. Add firmware attributes field
to fcparam structure.
MFC after:	4 weeks
2001-09-03 03:03:32 +00:00
Matt Jacob
126ec86486 Add 2 Gigabit Fibre Channel support (2300 && 2312 cards). This required
some reworking (and consequent cleanup) of the interrupt service code.

Also begin to start a cleanup of target mode support that will (eventually)
not require more inforamtion routed with the ATIO to come back with the
CTIO other than tag.

MFC after:	4 weeks
2001-08-31 21:39:04 +00:00
Matt Jacob
ed4bea259e Clean up some ways in which we set defaults for SCSI cards
that do not have valid NVRAM. In particular, we were leaving
a retry count set (to retry selection timeouts) when thats
not really what we want. Do some constant string additions
so that LOGDEBUG0 info is useful across all cards.

MFC after:	2 weeks
2001-08-20 17:28:32 +00:00
Matt Jacob
dec1985672 Add MBOX_GET_PCI_PARAMS alias.
MFC after:	2 weeks
2001-08-20 17:26:45 +00:00
Matt Jacob
169ad8cfef oops- typo in a previous commit 2001-08-16 17:39:45 +00:00
Matt Jacob
561e7bb942 Fix a spelling error in a comment. 2001-08-16 17:31:27 +00:00
Matt Jacob
dda035d1fc Add more MBOX and ASYNC event defines.
MFC after:	2 weeks
2001-08-16 17:26:03 +00:00
Matt Jacob
be534d5f1a Thanks to PHK for spotting: ISPASYNC_UNHANDLED_RESPONSE not
handle in isp_async.
2001-08-16 17:25:41 +00:00
Matt Jacob
50719f7521 Enable LIP F8, LIP Reset async events.
Be more chatty about SNS failures. Fix
typo for skipped phase mesage. Correct
MBOX_GET_PORT_QUEUE_PARAMS options in
table.

MFC after:	2 weeks
2001-08-16 17:25:08 +00:00
Matt Jacob
d51456f800 Oops- don't set 'goal' twice when you mean to set 'nvrm' as well.
This breaks bogus NVRAM boards.

MFC after:	1 day
2001-08-02 00:34:56 +00:00
Matt Jacob
9ce9bdaf8a Redo how we manage SCSI device settings- have a 3rd flags (nvram) that records
either what's in NVRAM or what the safe defaults would be if we lack NVRAM.
Then we rename cur_XXXX to actv_XXXX (these are the currently active settings)
and the dev_XXX settings to goal_XXXX (these are the settings which we want
cur_XXXX to converge to).

This probably isn't entirely final as yet- but it's a lot closer to now
being what it should be, including allowing camcontrol to actually set
specific settings.
2001-07-30 01:00:21 +00:00
Matt Jacob
d9c272f3ea Redo how we manage SCSI device settings- have a 3rd flags (nvram) that records
either what's in NVRAM or what the safe defaults would be if we lack NVRAM.
Then we rename cur_XXXX to actv_XXXX (these are the currently active settings)
and the dev_XXX settings to goal_XXXX (these are the settings which we want
cur_XXXX to converge to).

Roll core minor.
2001-07-30 00:59:32 +00:00
Matt Jacob
df225582bf Redo how we manage SCSI device settings- have a 3rd flags (nvram) that records
either what's in NVRAM or what the safe defaults would be if we lack NVRAM.
Then we rename cur_XXXX to actv_XXXX (these are the currently active settings)
and the dev_XXX settings to goal_XXXX (these are the settings which we want
cur_XXXX to converge to).
2001-07-30 00:59:06 +00:00
Matt Jacob
f44257c29a Remove ISP_SMPLOCK stuff- we're just using locking now.
Correctly reintroduce loop_seen_once semantics- that is, if we've never
seen good link, start bouncing commands with CAM_SEL_TIMEOUT. But we
have to be careful to have let ourselves try (in isp_kthread) to check
for loop up at least once.

PR:		28992
MFC after:	1 week
2001-07-25 04:23:52 +00:00
Matt Jacob
3910362ab8 Roll minor version. Remove ISP_SMPLOCK nonsense. We're using full locking,
and that's final.

MFC after:	1 week
2001-07-25 04:21:53 +00:00
Matt Jacob
761d6b7150 Hmm. Let's try this on for size...
We originally had it such that if the connection topology was FL-loop
(public loop), we never looked at any local loop addresses. The reason
for not doing that was fear or concern that we'd see the same local
loop disks reflected from the name server and we'd attach them twice.

However, when I recently hooked up a JBOD and a system to an ANCOR SA-8
switch, the disks did *not* show up on the fabric. So at least the
ANCOR is screening those disks from appearing on the fabric. Now, it's
possible this is a 'feature' of the ANCOR. When I get a chance, I'll
check the Brocade (it's hard to do this on a low budget).

In any case, if they *do* also show up on the fabric, we should
simply elect to not log into them because we already have an
entry for the local loop. There is relatively unexercised code
just for this case.

MFC after:	2 weeks
2001-07-11 02:34:21 +00:00
Matt Jacob
8e6a12fcad Oops- missed a CAMLOCK_2_ISP case. 2001-07-05 19:34:06 +00:00
Matt Jacob
45c9a36af5 Things have become cinched down more tightly about assertions for Giant.
This uncovered some missing spots where I trade off between isp's lock
and Giant as I enter CAM.
2001-07-05 17:14:57 +00:00
Matt Jacob
ab163f5fee Add CAM_NEW_TRAN_CODE support. Use correct CAMLOCK_2_ISPLOCK macros.
For fibre channel, start going for the gusto and using AC_FOUND_DEVICE
and AC_LOST_DEVICE calls to xpt_async when devices appear and disappear
as the loop or fabric changes.

ISPASYNC_FW_CRASH is the async event code where the platform layer
deals with a firmware crash.
2001-07-04 18:54:29 +00:00
Matt Jacob
9927912756 Macroize request/response in/out queue pointer access. 2001-07-04 18:52:23 +00:00
Matt Jacob
559a1ad2c1 Some possibly helpful casts. 2001-07-04 18:51:58 +00:00
Matt Jacob
f0f4c8ae4b Add a microcomment about how you'd use ispds64_t or ispdlist_t
for CTIO3/CTIO4 entries.
2001-07-04 18:51:06 +00:00
Matt Jacob
1ee34f05dd Add a bunch of additional defines for completion codes. Define
some of the RIO (reduced interrupt operation) stuff. Add 64 bit
data list (DSD type 1) and arbitrary data list (DSD type 2)
data structure defines.

Add macros that parameterize usage of the Request/Response in/out
queue pointers. When we finish 2300 support, different registers
will be accessed for the 2300.
2001-07-04 18:49:00 +00:00
Matt Jacob
b91862efef Firmware crashes handled in platform specific code (isp_async call).
Fix longstanding silly buglet that left a hole in the debug log defines.
2001-07-04 18:46:50 +00:00
Matt Jacob
9b9288ec4a More 2300 support prep- the Request/Response in/out pointers are
part of the PCI block for the 2300- not software convention usage
of the mailbox registers- so we macrosize in/out pointer usage.

Only report that a LIP destroyed commands if it actually destroyed
commands. Get the chan/tgt/lun order correct.  Fix a longstanding
stupid bug that caused us to try and issue a command with a tag on
Channel B because we were checking the tagged capability for the
target against Channel A.

A firmware crash is now vectored out to platform specific code
as an async event.

Some minor formatting tweaks.
2001-07-04 18:42:41 +00:00
Peter Wemm
22941bd78f Fix warnings:
554: passing arg 4 of `resource_string_value' from incompatible pointer type
576: passing arg 4 of `resource_string_value' from incompatible pointer type
593: passing arg 4 of `resource_string_value' from incompatible pointer type
2001-06-15 00:13:18 +00:00
Matt Jacob
cb62bc53d1 We've had problems with data corruption occuring on
commands that complete (with no apparent error) after
we receive a LIP. This has been observed mostly on
Local Loop topologies. To be safe, let's just mark
all active commands as dead if we get a LIP and we're
on a private or public loop.

MFC after:	4 weeks
2001-06-14 17:13:24 +00:00
Matt Jacob
6a23026c6e Fix botch for state levels. Role minor release. Start adding code for a
'force logout' path.

MFC after:	4 weeks
2001-06-05 17:11:06 +00:00
Matt Jacob
5d57194434 Spring MegaChange #1.
----

Make a device for each ISP- really usable only with devfs and add an ioctl
entry point (this can be used to (re)set debug levels, reset the HBA,
rescan the fabric, issue lips, etc).

----

Add in a kernel thread for Fibre Channel cards. The purpose of this
thread is to be woken up to clean up after Fibre Channel events
block things.  Basically, any FC event that casts doubt on the
location or identify of FC devices blocks the queues. When, and
if, we get the PORT DATABASE CHANGED or NAME SERVER DATABASE CHANGED
async event, we activate the kthread which will then, in full thread
context, re-evaluate the local loop and/or the fabric. When it's
satisfied that things are stable, it can then release the blocked
queues and let commands flow again.

The prior mechanism was a lazy evaluation. That is, the next command
to come down the pipe after change events would pay the full price
for re-evaluation. And if this was done off of a softcall, it really
could hang up the system.

These changes brings the FreeBSD port more in line with the Solaris,
Linux and NetBSD ports. It also, more importantly, gets us being
more proactive about topology changes which could then be reflected
upwards to CAM so that the periph driver can be informed sooner
rather than later when things arrive or depart.

---

Add in the (correct) usage of locking macros- we now have lock transition
macros which allow us to transition from holding the CAM lock (Giant)
and grabbing the softc lock and vice versa. Switch over to having this
HBA do real locking. Some folks claim this won't be a win. They're right.
But you have to start somewhere, and this will begin to teach us how
to DTRT for HBAs, etc.

--

Start putting in prototype 2300 support.  Add back in LIP
and Loop Reset as async events that each platform will handle.
Add in another int_bogus instrumentation point.

Do some more substantial target mode cleanups.

MFC after:	8 weeks
2001-05-28 21:20:43 +00:00
Matt Jacob
a1bc34c6b8 Redo a lot of the target mode infrastructure to be cognizant of Dual Bus
cards like the 1280 && the 12160. Cleanup isp_target_putback_atio.
Make sure bus and correct tag ids and firmware handles get propagated
as needed.
2001-04-04 21:58:29 +00:00
Matt Jacob
1209134a70 Roll platform minor.
Change target mode state definitions to be aware of 'channel' (for the
dualbus 1280/12160 cards).
2001-04-04 21:56:15 +00:00
Matt Jacob
e9a2738ad1 Complete some Ansification. Check to make sure, in tdma_mk, that we won't
overflow the request queue. The reason we want to do this is that we
now push out completed CTIOs as we complete them- this gets the QLogic
working on them quicker. So we need to know whether we can put the entire
burrito out before we start.

We now support conjoint status with data for the last CTIO for both Fibre
Channel and SCSI. Leave the old code in place in case we need to go back
(minor 3 line ifdef).

Ultra-ultra important- *don't* set rq->req_seg_count for non-data
target mode requests in isp_pci_dmasetup. D'oh- this is actually
the tag value area for a CTIO. What *was* I thinking? Boy howdy
does both aic7xxx and sym get awfully unhappy when on reconnect
you give them a constant '1' for a tag value.
2001-04-04 21:53:59 +00:00
Matt Jacob
b25bcef87a Perform some more Ansification. Remove and then replace the isp_putback_atio
function- we did it a bit cleaner. We only use this if a CTIO completes with
!CT_OK state. We now have managed to get away without having to poke around
and trying to find the original ATIO- the csio we're using has the tag_id
and lun values with it which is mostly what we need when we do the putback.

Make sure we correctly propagate AT_TQAE->CT_TQAE for tags. Make sure
we call ISP_DMAFREE only if we had DATA to move.
2001-04-04 21:49:51 +00:00
Matt Jacob
b5da7b232e Amazing. The bits to enable tagged queing in target mode, grok that a
tag is active for an ATIO, and say that you want to reconnect with
a tag value in a CTIO have *never* been exercised until now. This lossage
derived from Solaris code where this stuff originally came from that is
about 7 years old. Amazing.

We now bundle the incoming tag (legal values are 0..256) as the low
16 bits of the ccb_accept_tio's at_tagid while we put the firmware
handle for this ATIO in the top 16 bits- define some macros to make
this cleaner.

Complete some Ansification.
2001-04-04 21:46:48 +00:00
Matt Jacob
8055acd82d Add some target mode definitions and firmware (FC only) attribute definitions. 2001-04-04 21:44:10 +00:00
Matt Jacob
56f7a63a7a Ansification of source. 2001-04-04 21:43:43 +00:00
Matt Jacob
534bd9fecb After loading f/w, for FC cards print out Firmware Attributes.
Redo establishment of default SCSI parameters whether or not
we've been compiled for target mode. Unfortunately, the Qlogic
f/w is confused so that if we set all targets to be 'safe' (i.e.,
narrow/async), it will also then report narrow, async if we're
contacted in target mode from that target (acting in initiator
role). D'oh!

Fix ISPCTL_TOGGLE_TMODE to correctly enable the right channel for
dual channel cards. Add some more opcodes. Fix a stupid NULL
pointer bug.
2001-04-04 21:42:59 +00:00
John Baldwin
f34fa851e0 Catch up to header include changes:
- <sys/mutex.h> now requires <sys/systm.h>
- <sys/mutex.h> and <sys/sx.h> now require <sys/lock.h>
2001-03-28 09:17:56 +00:00
Matt Jacob
b72b15696c For parallel SCSI, let us now do status with the final CTIO. For the 1080,
I was hanging after sending a xfer CTIO and a status CTIO for a non-discon
INQUIRY- the xfer CTIO was returned as completed OK, but the status CTIO
was dropped on the floor. All the fields looked good. I don't know why
it got dropped. But allowing status to go back with data xfer seemed to
work. I also noticed that with a non-disconnecting command that the
firmware handle in the ATIO is zero- this leads me to believe that the
f/w really can only handle one CTIO at a time in the discon case, and
it had no idea what to do with the second (status) CTIO.
2001-03-21 00:49:37 +00:00
Matt Jacob
290dc24b4d Check CT2_SENDSTATUS/CT_SENDSTATUS against cto->ct_flags, not
CAM_SEND_STATUS. Set a timeout of 2 seconds per CTIO. Make sure
that the 'real' tag value is being checked against- not the
one that also carries the firmware handle.
2001-03-21 00:46:44 +00:00
Matt Jacob
b0bd9b71f2 Clean up usage- ct_reserved is really ct_syshandle now. 2001-03-14 04:14:58 +00:00
Matt Jacob
f5a4462713 First cut of target mode swizzling for non-little endian machines.
It's probably wrong but it's a start.
2001-03-14 04:14:22 +00:00
Matt Jacob
75f7d77928 Mote that how the pad bytes can be divided in half and used by either
the target mode code or outer layers.

Increase cd_tagval to be 32 bits since it will have to now carry 16
bits of parallel SCSI ATIO handle as well as a normal tag (if any).
2001-03-14 04:13:30 +00:00
Matt Jacob
e2ec5cf0f9 In order to save ourselves grief with the SUNPRO compiler under
Solaris (which, for reasons unknown to me, chokes on u_int16_t
as a typedef of unsigned short if used in a transitional (mixed K&R
and ANSI) way), we'll go the extra mile and fully ANSIfy things.
2001-03-14 04:11:56 +00:00
Matt Jacob
d8d5f2adc5 more 32 to 16 bit handle conversions 2001-03-04 18:42:51 +00:00
Matt Jacob
24d52eb7b5 More 32 to 16 bit handle stuff. Roll core minor version. 2001-03-04 18:42:23 +00:00
Matt Jacob
3bfa867765 Remove a superfluous newline in a string (isp_prt adds this).
Fix a missed conversion of 32 to 16 bit handles.
2001-03-04 18:41:23 +00:00
Matt Jacob
5f5aafe1fc Switch to using 16 bit handles instead of 32 bit handles.
This is a pretty invasive change, but there are three good
reasons to do this:

1. We'll never have > 16 bits of handle.
2. We can (eventually) enable the RIO (Reduced Interrupt Operation)
bits which return multiple completing 16 bit handles in mailbox
registers.
3. The !)$*)$*~)@$*~)$* Qlogic target mode for parallel SCSI spec
changed such that at_reserved (which was 32 bits) was split into
two pieces- and one of which was a 16 bit handle id that functions
like the at_rxid for Fibre Channel (a tag for the f/w to correlate
CTIOs with a particular command). Since we had to muck with that
and this changed the whole handler architecture, we might as well...

Propagate new at_handle on through int ct_fwhandle. Follow
implications of changing to 16 bit handles.

These above changes at least get Qlogic 1040 cards working in target
mode again. 1080/12160 cards don't work yet.

In isp.c:
Prepare for doing all loop management in outer layers.
2001-03-02 06:28:55 +00:00
Matt Jacob
715ec7e9a7 Fix isp_print_qentry to print all four lines- it's been broken for months. 2001-03-02 04:48:41 +00:00
Mark Murray
ed34d0ade2 Turn on interrupt-entropy harvesting for all/any mass storage devices
I could find. I have no doubt missed a couple.

Interrupt entropy harvesting is still conditional on the
kern.random.sys.harvest_interrupt sysctl.
2001-03-01 17:09:09 +00:00
Matt Jacob
6e5c5328c4 Eliminate the use of the getenv_int stuff we'd been using (with a bitmap
for selecting unit). Instead, use the resource hints mechanism.

One unfortunate situation here is that there is no resource_quad_value
function- which is what I needed for WWN boot time replacement. Worse-
you can't store the hint as just plain

hint.isp.0.nodewwn="0x50000000aaaa0001"

because this gets interpreted as an int- incorrectly because it can't
be converted to an int. I can't even get this as a string. To work
around this particular case for nodewwn && portwwn setting, this
rather grotesque form will be used:

hint.isp.0.nodewwn="w50000000aaaa0001"
hint.isp.0.portwwn="w50000000aaaa0002"

At the same time, if we have no hinted WWN, set the default WWN (which, btw,
gets overridden if the card has valid NVRAM, which is usual) to
0x400000007F000009ull (which translates to NAA == IPv4, 127.0.0.9).

Eliminate more printf's and replace them either with device_printf or
isp_prt calls.
2001-03-01 02:21:36 +00:00
Matt Jacob
c9a6d60b09 Go to a default port and default node wwn model. Eliminate isp_name
and isp_unit and just store the device_t, fer gosh sakes.... Include
sys/bus.h for use by isp_pci.c.
2001-03-01 02:15:58 +00:00
Matt Jacob
3c75bb14be Finally eliminate as many of the printf calls as possible (still leaving
ones where we have a CAM path) and replacing them with calls to isp_prt.,

Eliminate isp_unit references- we no longer have an isp_unit- we now
have an isp_dev that device_get_unit can work with.
2001-03-01 02:14:54 +00:00
Matt Jacob
b0a3ba7e28 Fix at2_entry_t to reflect what the firmware actually writes (instead
of just deriving from SCSI at_entry_t). In this case, there is no
'suggested sense' for FC cards.
2001-02-27 00:14:39 +00:00
Matt Jacob
4102f2f6ef Fix a longstanding bug- we had the sense of what bit 14
for the ICB firmware options meant- *I* had taken it to
mean that if you set it, Node Name would be ignored and
derived from Port Name. Actually, it meant the opposite.
As a consequence- change ICBOPT_USE_PORTNAME to the
define ICBOPT_BOTH_WWNS- makes more sense.

Fix wrong input bitmap for MBOX_DUMP_RAM command. Call
ISP_DUMPREGS if we get a f/w crash. Add ISPCTL_RUN_MBOXCMD
control command (so outer layers can run a mailbox command
directly) and add a ISPASYNC_UNHANDLED_RESPONSE hook so
outer layers can understand response queue entries we
might not know about.
2001-02-23 05:35:50 +00:00
Matt Jacob
410b556714 Eliminate ISP2100_FABRIC- we always allow for fabric now. Add an
isp_iid_set/isp_iid for fibre channel- this is because we now
fake a port database entry for ourselves. Add the additional loop
states between LOOP_PDB_RCVD and LOOP_READY.

Change and comment on a wad of Fibre Channel isp_control functions.
Change and comment on some of the ISPASYNC Fibre Channel events.
2001-02-11 03:56:48 +00:00
Matt Jacob
b21d3f4ef8 Add structure defining FC-AL position maps. The only tool that I know of
that really uses this is luxadm(8) under Solaris.
2001-02-11 03:53:58 +00:00
Matt Jacob
b9b599fe4c Shuffle around how we do isp_disable management- make sure we return 0 so
the unit number doesn't get reused.

Make sure that if we've compiled for ISP_TARGET_MODE we set the
default role to be ISP_ROLE_INITIATOR|ISP_ROLE_TARGET.

Do some misc other cleanups.
2001-02-11 03:53:23 +00:00
Matt Jacob
6b528b1a1e Add isp_fc_runstate function- this function's purpose is to, in stages,
and depending on role, make sure link is up, scan the fabric (if we're
connected to a fabric), scan the local loop (if appropriate), merge
the results into the local port database then, check once again
to make sure we have f/w at FW_READY state and the the loopstate
is LOOP_READY.
2001-02-11 03:52:04 +00:00
Matt Jacob
250bc0aa8b Roll minor version. Remove ISP2100_FABRIC define (unneeded now).
Comment out usage of ISP_SMPLOCK- I have my doubts that this works sanely
as yet because CAM itself still needs Giant. I *was* dropping my lock
and grabbing Giant when doing the upcall for completion, but this is all
seems ridiculous until CAM is fixed.
2001-02-11 03:48:54 +00:00
Matt Jacob
d6e5500f27 Do some cleanup based upon adapter role- mainly not enabling interrupts
if we're ISP_ROLE_NONE. Change ISPASYNC_LOGGED_INOUT to ISPASYNC_PROMENADE.
Make sure we note if something is a fabric device.

Target mode:
Finally fix (to a first approximation) SCSI Target Mode again- we needed
to correctly check against CAM_TARGET_WILDCARD and CAM_LUN_WILDCARD
so that targbh won't confuse us. Comment out the drainqueue stuff for
now. Use isp_fc_runstate instead if isp_control/ISPCTL_FCLINK_TEST.
2001-02-11 03:47:39 +00:00
Matt Jacob
b2b4adaa33 Minor stuff:
Remove ISP2100_FABRIC defines- we always handle fabric now. Insert
isp_getmap helper function (for getting Loop Position map). Make
sure we (for our own benefit) mark req_state_flags with RQSF_GOT_SENSE
for Fibre Channel if we got sense data- the !*$)!*$)~*$)*$ Qlogic
f/w doesn't do so. Add ISPCTL_SCAN_FABRIC, ISPCTL_SCAN_LOOP, ISPCTL_SEND_LIP,
and ISPCTL_GET_POSMAP isp_control functions. Correctly send async notifications
upstream for changes in the name server, changes in the port database, and
f/w crashes. Correctly set topology when we get a ASYNC_PTPMODE event.

Major stuff:
Quite massively redo how we handle Loop events- we've now added several
intermediate states between LOOP_PDB_RCVD and LOOP_READY. This allows us
a lot finer control about how we scan fabric, whether we go further
than scanning fabric, how we look at the local loop, and whether we
merge entries at the level or not. This is the next to last step for
moving managing loop state out of the core module entirely (whereupon
loop && fabric events will simply freeze the command queue and a thread
will run to figure out what's changed and *it* will re-enable the queu).
This fine amount of control also gets us closer to having an external
policy engine decide which fabric devices we really want to log into.
2001-02-11 03:44:43 +00:00
Bosko Milekic
9ed346bab0 Change and clean the mutex lock interface.
mtx_enter(lock, type) becomes:

mtx_lock(lock) for sleep locks (MTX_DEF-initialized locks)
mtx_lock_spin(lock) for spin locks (MTX_SPIN-initialized)

similarily, for releasing a lock, we now have:

mtx_unlock(lock) for MTX_DEF and mtx_unlock_spin(lock) for MTX_SPIN.
We change the caller interface for the two different types of locks
because the semantics are entirely different for each case, and this
makes it explicitly clear and, at the same time, it rids us of the
extra `type' argument.

The enter->lock and exit->unlock change has been made with the idea
that we're "locking data" and not "entering locked code" in mind.

Further, remove all additional "flags" previously passed to the
lock acquire/release routines with the exception of two:

MTX_QUIET and MTX_NOSWITCH

The functionality of these flags is preserved and they can be passed
to the lock/unlock routines by calling the corresponding wrappers:

mtx_{lock, unlock}_flags(lock, flag(s)) and
mtx_{lock, unlock}_spin_flags(lock, flag(s)) for MTX_DEF and MTX_SPIN
locks, respectively.

Re-inline some lock acq/rel code; in the sleep lock case, we only
inline the _obtain_lock()s in order to ensure that the inlined code
fits into a cache line. In the spin lock case, we inline recursion and
actually only perform a function call if we need to spin. This change
has been made with the idea that we generally tend to avoid spin locks
and that also the spin locks that we do have and are heavily used
(i.e. sched_lock) do recurse, and therefore in an effort to reduce
function call overhead for some architectures (such as alpha), we
inline recursion for this case.

Create a new malloc type for the witness code and retire from using
the M_DEV type. The new type is called M_WITNESS and is only declared
if WITNESS is enabled.

Begin cleaning up some machdep/mutex.h code - specifically updated the
"optimized" inlined code in alpha/mutex.h and wrote MTX_LOCK_SPIN
and MTX_UNLOCK_SPIN asm macros for the i386/mutex.h as we presently
need those.

Finally, caught up to the interface changes in all sys code.

Contributors: jake, jhb, jasone (in no particular order)
2001-02-09 06:11:45 +00:00
Jeroen Ruigrok van der Werven
f09deb6962 Fix typo: wierd -> weird.
There is no such thing as wierd in the english language.
2001-02-06 09:25:10 +00:00
Matt Jacob
d69a5f7d9c Guard against overflow of the calculated timeout value. 2001-01-16 07:15:36 +00:00
Matt Jacob
7afb656f3f Add was_fabric_dev/fabric_dev tags to our local FC database structure
(so we can see rapidly whether something was a fabric device but is
now gone).

Add a tag which says what role this adapter should take. It can take
on the value of None, Target, Initiator or Both. None is useful for
warm failover purposes. Remove the ISP_CFG_NOINIT silliness since
a role of "None" does this.

Add a isp_lastmbxcmd tag to store the opcode for the last mailbox
command used.
2001-01-15 18:40:37 +00:00
Matt Jacob
144ff11903 Put in offset definitions for FPM and FBM registers, plus just enough
bits defined so we can reset them.
2001-01-15 18:37:14 +00:00
Matt Jacob
df1590c05d Set default adapter role. 2001-01-15 18:36:39 +00:00
Matt Jacob
fe4a3254ce Use the isp_lastmbxcmd tag to report timed out mailbox commands.
Arrrggghhhh! Very likely fix 22650 by remembering to, ahem, set
CAM_AUTOSNS_VALID when one has sense data.
2001-01-15 18:36:09 +00:00
Matt Jacob
70d2cccebd Do more cleanup of the usage of 0..125 for F-port topologies. 2001-01-15 18:34:49 +00:00
Matt Jacob
6677e7f89e When resetting the Qlogic 2X00 units, reset the FPM (Fibre Protocol
Module) and FBM (Fibre Buffer Modules). Also remember to clear the
semaphore registers. Tell the RISC processor to not halt on FPM
parity errors.

Throw out the ISP_CFG_NOINIT silliness and instead go to the use of
adapter 'roles' to see whether one completes initialization or not
(mostly for Fibre Channel). The ultimate intent, btw, of all of this
is to have a warm standby adapter for failover reasons.  Because
we do roles now, setting of Target Capable Class 3 service parameters
in the ICB for the 2x00 cards reflects from role. Also, in isp_start,
if we're not supporting an initiator role, we bounce outgoing commands
with a Selection Timeout error. Also clean out the TOGGLE_TMODE
goop for FC- there is no toggling of target mode like there is
for parallel SCSI cards.

Do more cleanup with respect to using target ids 0..125 in F-port
topologies. Also keep track of things which *were* fabric devices
so that when you rescan the fabric you can notify the outer layers
when fabric devices go away.

Only force a LOGOUT for fabric devices if they're still logged in
(i.e., you cat their Port Database entry. Clean up the Get All Next
scanning.

Finally, use a new tag in the softc to store the opcode for the
last mailbox command used so we can report which opcode timed
out.
2001-01-15 18:33:08 +00:00
Matt Jacob
3fc3cadde6 ISPASYNC_PDB_CHANGED -> ISPASYNC_LOGGED_INOUT. 2001-01-09 02:49:02 +00:00
Matt Jacob
0ecded8a13 Add some SNS "Register FC4 type" subcommand defines. Add some defines
that are pertinetnt for state flags on Qlogic 2X00 status completion
entries.
2001-01-09 02:48:44 +00:00
Matt Jacob
27d1caa3cd Up tsleep && poll time for mailbox commands from 2 to 10 seconds. Print
out the mailbox command opcode if the command times out.
2001-01-09 02:47:56 +00:00
Matt Jacob
4b9d588e2c Follow the ISPASYNC_PDB_CHANGED -> ISPASYNC_LOGGED_INOUT change. Also,
ISPASYNC_NOTIFY_CHANGE now is for both local loop && fabric changes.
2001-01-09 02:47:15 +00:00
Matt Jacob
0433833d0d Add a isp_register_fc4_type function so that we work with McData switches
that require us to register our FC4 types of interest. Allow ourselves, in
F-port topologies, to start logging in fabric devices in the target 0..125
range. Change ISPASYNC_PDB_CHANGED (misnamed) to ISPASYNC_LOGGED_INOUT.
Fix (*SMACK*) again some default WWN stuff. This is *really* hard to get
right across all the range of platforms.
2001-01-09 02:46:23 +00:00
Matt Jacob
3486bfe084 add missing length argument 2001-01-09 02:12:42 +00:00
Matt Jacob
91f1caa2d8 Fix problems with incomplete conversions from printf to isp_prt. 2000-12-31 20:50:56 +00:00
Matt Jacob
56c6d0d775 Change the modification of what could be a const string. Apparently the
construct:

	char *foo;
	...
	foo = "XXX";
	...
	foo[1] = 'Y';

is wrong. IT blew up on NetBSD-sparc64 because that platform write-protects
constant strings.
2000-12-30 20:09:26 +00:00
Matt Jacob
e9423e211e Add in Bill Sommerfeld's -Wformat stuff. Add a ISP_CFG_NOINIT option
to keep from completing initialization when isp_init is called.
2000-12-29 19:17:18 +00:00
Matt Jacob
8ead30564e Add in Bill Sommerfelds -Wformat changes. Set up default node && port
WWNs correctly (Again!) - this time for the case that we're not going
to fully init the adapter if isp_init is called (with ISP_CFG_NOINIT
set in options). The pupose for this is to bring the adapter up to
almost ready to go, get info out of NVRAM, but to not start it up- leaving
it until later to actually start things up if wanted (and possibly with
different roles selected).
2000-12-29 19:12:44 +00:00
Matt Jacob
f09b192280 Set up to do a local interrupt fielding before calling common code-
allows us to grab lock as we should.
2000-12-29 19:10:16 +00:00
Matt Jacob
c40e096ed6 Make sure we do locking if we call isp_intr.
Make sure we enter Giant for now if we call into cam for completion.
2000-12-29 19:06:32 +00:00
Matt Jacob
7325560821 add a couple off offset defines for ATIO2s 2000-12-28 23:27:54 +00:00
David Malone
7cc0979fd6 Convert more malloc+bzero to malloc+M_ZERO.
Submitted by:	josh@zipperup.org
Submitted by:	Robert Drehmel <robd@gmx.net>
2000-12-08 21:51:06 +00:00
Matt Jacob
4081cc88c9 Only call ISP_UNLOCK/ISP_LOCK if isp->isp_osinfo.intsok in USEC_SLEEP.
Add a test against isp->isp_osinfo.islocked prior to trying to see
whether --isp->isp_osinfo.islocked is zero to cause us to unlock
(non-SMPLOCK case).
2000-12-05 07:41:53 +00:00
Matt Jacob
bfbab17021 Replace some more printfs with isp_prt's. Use isp_prt/ISP_LOGDEBUG0
for rate setting/getting printouts.
2000-12-05 07:39:54 +00:00
Matt Jacob
f7dddf8a54 Remove more printfs and use either isp_prt or device_printf. Remember
to set ISP_LOGINFO if bootverbose is set.
2000-12-05 07:38:41 +00:00
David Malone
ea8b5a9ae9 More M_ZERO patches.
Submitted by:	josh@zipperup.org
Submitted by:	Robert Drehmel <robd@gmx.net>
Approved by:	mjacob
2000-12-03 20:46:54 +00:00
Matt Jacob
e5f2f488c5 Add USEC_SLEEP macro support. Change the location at which we define
ISP_LOCK/ISP_UNLOCK macros.
2000-12-02 18:33:29 +00:00
Matt Jacob
81babfd043 Make the Not RESPONSE in RESPONSE QUEUE message have a bit more info
(specifically, how many entries we've looked at so far). Maintain
interrupt instrumentation. Use USEC_SLEEP instead of USEC_DELAY in
a number of places (this allows us to drop locks and sleep instead
of spin). Track changes to configuration options for topology preference.
Fix botched order of printout for Channel, Target, Lun.
2000-12-02 18:08:35 +00:00
Matt Jacob
67afe757a2 Add interrupt instrumentation. Change ISP_CFG_NPORT config option to
a set of options that allows specific loop, loop-only, nport, nport-only
topology settings. Define a required macro for all platforms (USEC_SLEEP).
2000-12-02 18:06:03 +00:00
Matt Jacob
aa0898c0e0 I'm dropping the MAINTAINER request and see what happens. If it becomes
too hard for me to keep in sync with other platforms, FreeBSD will go
it's own way.
2000-10-31 05:55:54 +00:00
Matt Jacob
650789cb1b Get rid of ridiculous ISP_PVS macro. Instead, just set an
ISP_SMPLOCK define based on the previous 5.4 major/minor release
define of PVS- because this allows us to turn it off easier.
2000-10-25 04:42:46 +00:00
Matt Jacob
3395b0568a Whoops! Forgot to commit this when I committed the other (turnin on locks)
change. Sorry about that.
2000-10-25 04:40:49 +00:00
John Baldwin
35e0e5b311 Catch up to moving headers:
- machine/ipl.h -> sys/ipl.h
- machine/mutex.h -> sys/mutex.h
2000-10-20 07:58:15 +00:00
Matt Jacob
e92fbe47e2 Roll minor revision- for once we'll use this because.... if revision >= 5.4,
compile time will build in mutex locks, otherwise the old locking (splcam/splx
with a recursion counter) will be compiled in.

We still depend on config_intr_hook to tell us when it's okay to call
msleep instead of polling. It'd be real nice if we could do this early
enough to not hang up a machine struggling with a bad Fibre Channel loop,
but that's still to come.
2000-10-17 18:18:14 +00:00
Matt Jacob
39f3fc6f69 remove "SERVICING_INTERRUPT" nonsense 2000-10-17 18:15:30 +00:00
Poul-Henning Kamp
db7e3af111 Remove unneeded #include <machine/clock.h> 2000-10-15 14:19:01 +00:00
Matt Jacob
e5d4e19714 Make changes required by change in how default and usable node and port
WWNS are made and used.
2000-10-12 23:59:40 +00:00
Matt Jacob
c914d4237d Redo how default Node and Port WWNs are determined (again!). This is so
we don't stomp on the differences between ports for a Qlogic 2202.
2000-10-12 23:49:09 +00:00
Matt Jacob
9cf43b9716 Change some default macro usages/definitions/requirements. 2000-10-12 23:47:03 +00:00
Matt Jacob
aa57fd6fa5 some copyright cleanups 2000-09-21 20:16:04 +00:00
Matt Jacob
c0cfc79790 Inintialize the queue index stuff from what the f/w sends back- just
in case it's insane enough to not do what you tell it to.

Print out (LOGINFO level) initiator ID.
2000-09-21 17:06:45 +00:00
Matt Jacob
e11a1ee870 Per msmith's request, don't attach to Qlogic 12160 id'd cards that have
a certain SubVendorID.
2000-09-07 20:27:40 +00:00
Doug Rabson
21c3015a24 * Completely rewrite the alpha busspace to hide the implementation from
the drivers.
* Remove legacy inx/outx support from chipset and replace with macros
  which call busspace.
* Rework pci config accesses to route through the pcib device instead of
  calling a MD function directly.

With these changes it is possible to cleanly support machines which have
more than one independantly numbered PCI busses. As a bonus, the new
busspace implementation should be measurably faster than the old one.
2000-08-28 21:48:13 +00:00
Matt Jacob
84267b9edd remove clause 3 licence 2000-08-27 23:39:23 +00:00
Matt Jacob
b6b6ad2f23 various fixes 2000-08-27 23:38:44 +00:00
Matt Jacob
3ea883b46d Add a comment as to where stdarg.h applies. 2000-08-03 03:05:50 +00:00
John Baldwin
7d615c1d8b Use <machine/stdarg.h> instead of <stdarg.h> so that this will compile.
While I'm at it, move the #include line up to the top of the file.
2000-08-03 02:47:06 +00:00
Matt Jacob
c7d5594134 Add in macros && masks so that mailbox command errors can be
selectively printed/supressed in isp_mboxcmd.
2000-08-01 06:55:08 +00:00
Matt Jacob
d0d5832ac7 Major whacking for core version 2.0. A major motivator for 2.0 and these
changes is that there's now a Solaris port of this driver, so some things
in the core version had to change (not much, but some).

In order, from the top.....:

A lot of error strings are gathered in one place at the head of the file.
This caused me to rewrite them to look consistent (with respect to
things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'.

The major mailbox function, isp_mboxcmd, now takes a third argument,
which is a mask that selectively says whether mailbox command failures
will be logged. This will substantially reduce a lot of spurious noise
from the driver.

At the first run through isp_reset we used to try and get the current
running firmware's revision by issuing a mailbox command. This would
invariably fail on alpha's with anything but a Qlogic 1040 since SRM
doesn't *start* the f/w on these cards. Instead, we now see whether we're
sitting ROM state before trying to get a running BIOS loaded f/w version.

All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to
isp_prt. There are seperate print levels that can be independently
set (see ispvar.h), which include debugging, etc.

All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and
RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel
cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry
indices, so we can make a 1024 entry index for them instead of the
256 entries we've had until now.

A major change it to fix isp_fclink_test to actually only wait the
delay of time specified in the microsecond argument being passed.
The problem has always been that a call to isp_mboxcmd to get he
current firmware state takes an unknown (sometimes long) amount of
time- this is if the firmware is busy doing PLOGIs while we ask
it what's up. So, up until now, the usdelay argument has been
a joke. The net effect has been that if you boot without being plugged
into a good loop or into a switch, you hang. Massively annonying, and
hard to fix because the actual time delta was impossible to know
from just guessing. Now, using the new GET_NANOTIME macros, a precise
and measured amount of USEC_DELAY calls are done so that only the
specified usecdelay is allowed to pass. This means that if the initial
startup of the firmware if followed by a call from isp_freebsd.c:isp_attach
to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000,
no more than two seconds will actually elapse before we leave concluding
that the cable is unhooked. Jeez. About time....

Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE
macro to a call to the platform supplied isp_done (sane naming).

Limit our size of request queue completions we'll look at at interrupt
time. Since we've increased the size of the Request Queue (and the
size of the Response Queue proportionally), let's not create an
interrupt stack overflow by having to keep a max completion list
(forw links are not an option because this is common code with
some platforms that don't have link space in their XS_T structures).
A limit of 32 is not unreasonable- I doubt there'd be even this many
request queue completions at a time- remember, most boards now use
fast posting for normal command completion instead of filling out
response queue entries.

In the isp_mboxcmd cleanup, also create an array of command
names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8".

Remove the isp_lostcmd function- it's been deprecated for a while.
Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus
register dump fucntion.

Various other cleanups.
2000-08-01 06:51:05 +00:00
Matt Jacob
b09b009594 Core version 2.0 rewrite. In this file we replace isp_tdebug with
isp_prt calls. We now use an argument to the  ISPCTL_FCLINK_TEST
call. We change all IDPRINTF macros to isp_prt calls. We add
the isp_prt function here.
2000-08-01 06:31:44 +00:00
Matt Jacob
18ccaecd45 Core version 2.0 cleanup/rewrite. Things get rearranged and changed
quite a bit so that all of the ports have a similar set of required
macros/definitions (and in similar places in the isp_<platform>.h
file).

Some new macros/functions added- Mailbox Acquire/Relase macros,
NANOTIME macros, SNPRINTf and STRNCAT. MemoryBarrier beomes
MEMORYBARRIER with much stronger types.
2000-08-01 06:29:55 +00:00
Matt Jacob
16dd34376c Remove isp_prtstst (now in case statement in isp.c). Remove
isp2100_fw_statename as an INLINE (now a function in isp.c). Remove
isp2100_pdb_statename (unused). Redo all ISP_SCSI_XFER_T as XS_T types.
Change all RQUEST_QUEUE_LEN/RESULT_QUEUE_LEN macros to take a parameter.
Add isp_print_bytes function.
2000-08-01 06:26:04 +00:00
Matt Jacob
10549c059a Remove isp_tdebug. Change all PRINTF macros to the now common
isp_prt logging function.
2000-08-01 06:24:01 +00:00
Matt Jacob
69fbe07a2e Fix typo. Remove isp_tdebug (we'll use ISP_LOGTDEBUG2 in isp->isp_dblev
as a selector now). Change DFLT_CMD_CNT to a fixed amount for now.
2000-08-01 06:23:24 +00:00
Matt Jacob
a6db0ba6d3 Add in lengths of SBus or PCI registers. 2000-08-01 06:21:21 +00:00
Matt Jacob
53cff3bb65 Rewrite for version 2.0. Some structural changes, but also
a substantial amount of commenting about what each platform
specific definitions are supposed to be.
2000-08-01 06:10:21 +00:00
Matt Jacob
d02373f1a0 Part of major rewrite for core version 2.0- clarification of
mdvec structure, removal of printf/CFGPRINTF in place of isp_prt
calls. Parameterization of RQUEST_QUEUE_LEN/RESULT_QUEUE_LEN.
2000-08-01 05:16:49 +00:00