of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.
The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.
The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.
Reviewed by: freebsd-net
operands. `movw' could be used, but instead let the assembler decide
the right instruction to use.
2. AT&T asm syntax requires a leading '*' in front of the operand for
indirect calls and jumps.
<sys/bio.h>.
<sys/bio.h> is now a prerequisite for <sys/buf.h> but it shall
not be made a nested include according to bdes teachings on the
subject of nested includes.
Diskdrivers and similar stuff below specfs::strategy() should no
longer need to include <sys/buf.> unless they need caching of data.
Still a few bogus uses of struct buf to track down.
Repocopy by: peter
source address when receiving frames (and keep using address 2 when in
pseudo-IBSS mode). This is apparently necessary in order to obtain the
true MAC address of the sending station which is needed for PPPoE.
Patch supplied by: Blaz Zupan <blaz@amis.net>
- Add support for using the PCI BIOS functions for configuration space
accesses, and make this the default.
- Make PNPBIOS the default (obsoletes the PNPBIOS config option).
- Add two new boot-time tunables to disable each of the above.
Exceptions:
Vinum untouched. This means that it cannot be compiled.
Greg Lehey is on the case.
CCD not converted yet, casts to struct buf (still safe)
atapi-cd casts to struct buf to examine B_PHYS
non-device code.
* Re-implement the method dispatch to improve efficiency. The new system
takes about 40ns for a method dispatch on a 300Mhz PII which is only
10ns slower than a direct function call on the same hardware.
This changes the new-bus ABI slightly so make sure you re-compile any
driver modules which you use.
(Much of this done by script)
Move B_ORDERED flag to b_ioflags and call it BIO_ORDERED.
Move b_pblkno and b_iodone_chain to struct bio while we transition, they
will be obsoleted once bio structs chain/stack.
Add bio_queue field for struct bio aware disksort.
Address a lot of stylistic issues brought up by bde.
fe_read_eeprom_rex() and fe_init_rex(). These functions should be
useful for REX-5580 series (for PC-AT). But they are included in
`#ifdef PC98' to avoid warnings by unused static functions. If you
try to support REX-5580, please be aware of these functions.
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
removed unncessary MPLOCKED and 'lock' prefixes from the interrupt
nesting level, since (A) the MP lock is held at the time, and (B) since
the neting level is restored prior to return any interrupted code
will see a consistent value.
includes one of bus_at386.h and bus_pc98.h. Becuase only bus_pc98.h
supports indirect pio and bus_at386.h is identical to old bus.h, there
is no functional change in PC-AT's kernels. That is, it cannot cause
performance loss.
Submitted by: nyan
Reviewed by: imp
bde and luoqi provided useful comments for earlier version.
syscall path inward. A system call may select whether it needs the MP
lock or not (the default being that it does need it).
A great deal of conditional SMP code for various deadended experiments
has been removed. 'cil' and 'cml' have been removed entirely, and the
locking around the cpl has been removed. The conditional
separately-locked fast-interrupt code has been removed, meaning that
interrupts must hold the CPL now (but they pretty much had to anyway).
Another reason for doing this is that the original separate-lock for
interrupts just doesn't apply to the interrupt thread mechanism being
contemplated.
Modifications to the cpl may now ONLY occur while holding the MP
lock. For example, if an otherwise MP safe syscall needs to mess with
the cpl, it must hold the MP lock for the duration and must (as usual)
save/restore the cpl in a nested fashion.
This is precursor work for the real meat coming later: avoiding having
to hold the MP lock for common syscalls and I/O's and interrupt threads.
It is expected that the spl mechanisms and new interrupt threading
mechanisms will be able to run in tandem, allowing a slow piecemeal
transition to occur.
This patch should result in a moderate performance improvement due to
the considerable amount of code that has been removed from the critical
path, especially the simplification of the spl*() calls. The real
performance gains will come later.
Approved by: jkh
Reviewed by: current, bde (exception.s)
Some work taken from: luoqi's patch
not introduce (hopefully) any functional changes but gets rid of
the #ifdef spaghetti pcvt suffered from more and more over the
years.
Several no more used parts of the source were removed, others
which are used by default are now non-optional components:
PCVT_NETBSD removed completety
PCVT_FREEBSD removed option, code is now standard
PCVT_KBD_FIFO removed option, code is now standard
PCVT_EMU_MOUSE removed completety
PCVT_SW0CNOUTP removed completety
PCVT_PORTIO_DELAY obsolete, removed
PCVT_KEYBDID removed option, code is now standard
PCVT_SIGWINCH removed option, code is now standard
PCVT_PALFLICKER removed completety
PCVT_WAITRETRACE removed completety
PCVT_NOFASTSCROLL removed option, code is now standard
PCVT_USL_VT_COMPAT removed the "old" non-vt Xserver code completely,
depending on XSERVER, this code is now standard.
Pcvt userland cleanup will follow as well as newbusifying the
kernel part.
Make the public interface more systematically named.
Remove the alternate method, it doesn't do any good, only ruins performance.
Add counters to profile the usage of the 8 access functions.
Apply the beer-ware to my code.
The weird +/- counts are caused by two repocopies behind the scenes:
kern/kern_clock.c -> kern/kern_tc.c
sys/time.h -> sys/timetc.h
(thanks peter!)
field in struct buf: b_iocmd. The b_iocmd is enforced to have
exactly one bit set.
B_WRITE was bogusly defined as zero giving rise to obvious coding
mistakes.
Also eliminate the redundant struct buf flag B_CALL, it can just
as efficiently be done by comparing b_iodone to NULL.
Should you get a panic or drop into the debugger, complaining about
"b_iocmd", don't continue. It is likely to write on your disk
where it should have been reading.
This change is a step in the direction towards a stackable BIO capability.
A lot of this patch were machine generated (Thanks to style(9) compliance!)
Vinum users: Greg has not had time to test this yet, be careful.
it's options COMPAT_OLDISA and COMPAT_OLDPCI. This is meant to be a
fairly strong incentive to update the older drivers to newbus, but doesn't
(quite) leave anybody hanging with no hardware support. I was talking with
a few folks and I was encouraged to simply break or disable the shims but
that was a bit too drastic for my liking.
prevent a page fault if the card is ejected while BPF is in use. This
could happen if DHCP or tcpdump was in use on that interface during
ejection. Other drivers may also require this modification.
Reviewed by: wes
new-bus Olicom driver, previously known as "ol". The new
driver unfortunately does not support ISA cards yet.
o Update the microcode files, interface library and include files
to the latest PowerMACH works version. Force even byte alignment
of adapter microcode.
o Roll in some of the patches from Nikolai Saoukh <nms@ethereal.ru>.
- Properly keep track of resources (I/O ports and irq).
- Use bus_space_read/write() to access the ports.
- Add PnP IDs.
- Add a watchdog timer in case interrupts are lost (experimental).
- Add `detach' function (experimental).
fixes some namespace pollution in general and breakage of modules that
aren't in the sys tree in particular (<machine/ipl.h> includes further
headers that aren't installed under /usr/include).
Reimplemented SPLASSERT() so that it is more machine independent and
less bloated and doesn't require the <machine/ipl.h> include spam.
In particular, don't assume that `cpl' can be printed using %08x
format. The alpha arch doesn't even have `cpl'. SPLASSERT() was
harmless on alphas because it isn't actually used.
chipset to be probed & attached on newer Dell PowerEdge servers, such as
the 2400 and 4400.
Reviewed by: dfr, msmith, jlemon
Tested by: hnokubi@yyy.or.jp (in a previous incantation)
Approved by: jkh
Also update wicontrol to enable/disable encryption, set WEP keys and set the
TX key index. Silver cards only have 40-bit keys. This is something of a quick
hack, but it works well enough for me to commit this from the LinuxWorld
exhibit floor.
The WEP support only shows up if you have a card that supports it.
Would have been approved by: jkh, if he hadn't wandered off somewhere
Approved in his place by: msmith, who's standing right here
be safe enough to recommend for working around the problem with CHS mode
normally being limited to 65536*16*63 sectors.
Fixed bitrot in related debugging code.
Fixed related style bugs.
Removed another vestige of bad144 support.
actually used it since the only device that specified it (vga0) was marked
as "FLG_INVISIBLE" in userconfig and therefore never shown.
Suggested by: bde
are using an old unconverted driver. Most (if not all) of the drivers
for common hardware are newbus these days. However, we don't want
to encourage people to take the easy way out and write new drivers
using the shims. This is just passive "encouragement".
Reviewed by: phk
subr_diskmbr.c:
Don't "helpfully" enlarge our idea of the disk size to cover all the
primary slices. Instead, truncate or discard slices that don't seem
to be on the disk. The enlargement was a hack for disks that don't
report their size (e.g., MFM disks). It is just wrong in general.
wd.c:
In CHS mode, limit the disk size so that cylinder numbers >= 65536
cannot occur. This normally only affects disks larger than 33.8GB.
CHS mode accesses to addresses above the limit are now properly broken
(an error is returned instead of garbage for reads and disk corruption
for writes).
PR: 15611
Reviewed by: readers of freebsd-bugs did not respond to a request
for review
same object file (atapi-cd.o) as the ata drivers. I'd have called it
wcd.[ch], but there's already one of those in the Attic that we can't
clobber - the good names are taken.
Fix building so that it can be compiled into LINT alongside ata.
Requested by: bde
isa_device->id_ri_flags and RI_FAST were not implemented and did nothing.
The two drivers that were mistakenly thinking this was working were
cy.c and loran.c - these should be converted to newbus.
GC (garbage collect) isa_device->id_alive
GC userconfig.c references to isa_device->id_scsiid (!).
unless both "option INVARIANTS" and "options INVARIANT_SUPPORT"
are defined in the kernel's config(8) file.
SPLASSERT(expression, msg) used KASSERT to check that the
expression is true, panic()ing the kernel otherwise.
Approved by: jkh
Reviewed by: jdp, dfr, phk, eivind and green
Collect together the components of several drivers and export eisa from
the i386-only area (It's not, it's on some alphas too). The code hasn't
been updated to work on the Alpha yet, but that can come later.
Repository copies were done a while ago.
Moving these now keeps them in consistant place across the 4.x series
as the newbusification progresses.
Submitted by: mdodd
things like sound cards can get called "Parallel port". A note to the
unwary; the isa-pnp devices in the system are probed like PCI - each
device ID is passed to *all* isa probe routines to find the best match.
If the driver is not prepared to deal with this, it must abort in this
scenario or it will try and claim all PnP devices.
Note1: the correct interrupt level is invoked correctly for each driver.
For this purpose, drivers request the bus before being able to
call BUS_SETUP_INTR and BUS_TEARDOWN_INTR call is forced by the ppbus
core when drivers release it. Thus, when BUS_SETUP_INTR is called
at ppbus driver level, ppbus checks that the caller owns the
bus and stores the interrupt handler cookie (in order to unregister
it later).
Printing is impossible while plip link is up is still TRUE.
vpo (ZIP driver) and lpt are make in such a way that
using the ZIP and printing concurrently is permitted is also TRUE.
Note2: specific chipset detection is not done by default. PPC_PROBE_CHIPSET
is now needed to force chipset detection. If set, the flags 0x40
still avoid detection at boot.
Port of the pcf(4) driver to the newbus system (was previously directly
connected to the rootbus and attached by a bogus pcf_isa_probe function).
layout. It seems that I cleaned it up a bit too much and confused a few
if () {
if () {
} else {
}
}
statements in the obvious manner.
This allows the driver to transmit packets again. *sigh*
ddb is entered. Don't refer to `in_Debugger' to see if we
are in the debugger. (The variable used to be static in Debugger()
and wasn't updated if ddb is entered via traps and panic anyway.)
- Don't refer to `in_Debugger'.
- Add `db_active' to i386/i386/db_interface.d (as in
alpha/alpha/db_interface.c).
- Remove cnpollc() stub from ddb/db_input.c.
- Add the dbctl function to syscons, pcvt, and sio. (The function for
pcvt and sio is noop at the moment.)
Jointly developed by: bde and me
(The final version was tweaked by me and not reviewed by bde. Thus,
if there is any error in this commit, that is entirely of mine, not
his.)
Some changes were obtained from: NetBSD
the low level interrupt handler number should be used. Change
setup_apic_irq_mapping() to allocate low level interrupt handler X (Xintr${X})
for any ISA interrupt X mentioned in the MP table.
Remove an assumption in the driver for the system clock (clock.c) that
interrupts mentioned in the MP table as delivered to IOAPIC #0 intpin Y
is handled by low level interrupt handler Y (Xintr${Y}) but don't assume
that low level interrupt handler 0 (Xintr0) is used.
Don't allocate two low level interrupt handlers for the system clock.
Reviewed by: NOKUBI Hirotaka <hnokubi@yyy.or.jp>
Aaron Campbell <aaron@cs.dal.ca>.
Use SHIFT-PgUp and SHIFT-PgDn to scroll back and forward.
Aarons original code was enhanced to have a separate scrollbuffer
for every virtual terminal and to preserve the screen contents
when switching screen sizes.
The scrollbuffer size is currently fixed at 8 pages but this
will be made configurable through the use of scon(1) in the
near future.
For pcvt_kbd.h, a longstanding compiler warning was fixed by
using excessive backetizing of the key2ascii[] table.
is an application space macro and the applications are supposed to be free
to use it as they please (but cannot). This is consistant with the other
BSD's who made this change quite some time ago. More commits to come.
is not configured. Including <isa/isavar.h> when it is not used is
harmful as well as bogus, since it includes "isa_if.h" which is not
generated when isa is not configured.
Some interface botches went away, leaving the macros unused outside of
the implementation of interrupt masking, and it was silly for the
implementation to use the macros in only one place each.
apm_default_resume() to sometimes set a very wrong time.
(1) Accesses to the RTC index and data registers were not atomic enough.
Interrupts were not masked. This was only good enough until an
interrupt handler (rtcintr()) started accessing the RTC in FreeBSD-2.0.
(2) Access to the block of time registers in inittodr() was not atomic
enough. inittodr() has 244us to read the time registers. Interrupts
were not masked. This was only good enough until something (apm)
started calling inittodr() after boot time in FreeBSD-2.0.
The fix for (2) also makes the timecounter update more atomic, although
this is currently unimportant due to the low resolution of the RTC.
Problem reported by: mckay
3.3R and then to -current. The pccard support has been left in the
driver, but is presently non-functional because we are using the
isa_compat layer for the moment.
Obtained From: PAO
Sponsored by: Timing Solutions
These drivers were cloned from the ed and ep drivers back in 1994
when PCMCIA cards were a very new thing and we had no other support
for such devices. They treated the PCIC (the chip which controls the
PCCARD slot) as part of their device and generally hacked their way
to success. They have significantly bit-rotted relative to their
ancestor drivers (ed & ep) and they were a dead-end on the evolution
path to proper PCCARD support in FreeBSD.
They have been terminally broken since August 18 where mdodd forgot
them and nobody seems to have missed them enough to fix them since.
I found no outstanding PRs against these drivers.
The same goes for CD drivers and tape drivers. In systems with mixed IDE
and SCSI, devices in the same priority class will be sorted in attach
order.
Also, the 'CCD' priority is now the 'ARRAY' priority, and a number of
drivers have been modified to use that priority.
This includes the necessary changes to all drivers, except the ATA drivers.
Soren will modify those separately.
This does not include and does not require any change in the devstat
version number, since no known userland applications use the priority
enumerations.
Reviewed by: msmith, sos, phk, jlemon, mjacob, bde
xxx_query_mode() in the vga and vesa drivers.
- xxx_query_mode() returns 0 (success) and a positive error number.
- Copy mode information on success.
- Remove redundant structure copy.
The bug first found in -STABLE by jmg.
forgot to do when he converted it to newbus.
Note: make *sure* to remove any old joy.o object files from your kernel
build directories in order to be sure the joy driver is properly recompiled.
Noticed by: phk
Copied from i386/isa/atapi.c.
Fixed to support slave devices.
Ignore the device that has strange model strings.
i386/isa/atapi.c
Removed pc98 codes.
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
device_add_child_ordered(). 'ivars' may now be set using the
device_set_ivars() function.
This makes it easier for us to change how arbitrary data structures are
associated with a device_t. Eventually we won't be modifying device_t
to add additional pointers for ivars, softc data etc.
Despite my best efforts I've probably forgotten something so let me know
if this breaks anything. I've been running with this change for months
and its been quite involved actually isolating all the changes from
the rest of the local changes in my tree.
Reviewed by: peter, dfr
- Convert to new bus attachment scheme. Thanks to Blaz Zupan for doing
the initial work here. One thing I changed was to have the attach
and detach routines work like the PCI drivers, which means that in
theory you should be able to load and unload the driver like the PCI
NIC drivers, however the pccard support for this hasn't settled down
yet so it doesn't quite work. Once the pccard work is done, I'll have
to revisit this.
- Add device wi0 to PCCARD. If we're lucky, people should be able to
install via their WaveLAN cards now.
- Add support for signal strength caching. The wicontrol utility has
also been updated to allow zeroing and displaying the signal strength
cache.
- Add a /sys/modules/wi directory and fix a Makefile to builf if_wi.ko.
Currently this module is only built for the i386 platform, though once
the pccard stuff is done it should be able to work on the alpha too.
(Theoretically you should be able to plug one of the WaveLAN/IEEE ISA
cards into an alpha with an ISA slot, but we'll see how that turns out.
- Update LINT to use only device wi0. There is no true ISA version of
the WaveLAN/IEEE so we'll never use an ISA attachment.
- Update files.i386 so that if_wi is dependent on card.
to use a locked cmpexg when unlocking a lock that we already hold, since
nobody else can touch the lock while we hold it. Second, it is not
necessary to use a locked cmpexg when locking a lock that we already
hold, for the same reason. These changes will allow MP locks to be used
recursively without impacting performance.
Modify two procedures that are called only by assembly and are already
NOPROF entries to pass a critical argument in %edx instead of on the
stack, removing a significant amount of code from the critical path
as a consequence.
Reviewed by: Alfred Perlstein <bright@wintelcom.net>, Peter Wemm <peter@netplex.com.au>
host->pci bridge specifically, then add a pcib0 device on the motherboard
for the pci bus to hang off.
Requested by: Anders Andersson <anders@sanyusan.se>
Obtained from: dfr
the countdown register.
this should not be necessary but there are broken laptops that
do not restore the countdown register on resume.
when it happnes, it messes up the hardclock interval and system clock,
which leads to the infamous "calcru: negative time" problem.
Submitted by: kjc, iwasaki
Reviewed by: Steve O'Hara-Smith <steveo@eircom.net> and committers.
Obtained from: PAO3
Merge the contents (less some trivial bordering the silly comments)
of <vm/vm_prot.h> and <vm/vm_inherit.h> into <vm/vm.h>. This puts
the #defines for the vm_inherit_t and vm_prot_t types next to their
typedefs.
This paves the road for the commit to follow shortly: change
useracc() to use VM_PROT_{READ|WRITE} rather than B_{READ|WRITE}
as argument.
Note to self; when converting a driver to newbus, the foodriver bits
must be removed from sys/i386/isa/isa_compat.h
Reminded gently by: Mitsuru IWASAKI <iwasaki@jp.FreeBSD.org>
if_fe.c uses PCCARD_MODULE() and is part of GENERIC. I've #ifdef'ed out
the #include of "card.h" to hopefully disable pccard support in this
driver until it can be converted. I'm not positive this will fix make
release, but it can't possibly make it any worse than it is now.
I hope this stuff settles down soon.
Been in production for 3 years now. Gives Instant Frame relay to if_sr
and if_ar drivers, and PPPOE support soon. See:
ftp://ftp.whistle.com/pub/archie/netgraph/index.html
for on-line manual pages.
Reviewed by: Doug Rabson (dfr@freebsd.org)
Obtained from: Whistle CVS tree
- Generally clean things up.
- PnP now supported.
Will convert to bus_space, ifmedia and add a DEVICE_IDENTIFY() method
for autodetection. As it stands
device ex0 at isa0
should find a card if one is present.
I feel less dirty now.
resource_list_release. This removes the dependancy on the
layout of ivars.
* Move set_resource, get_resource and delete_resource from
isa_if.m to bus_if.m.
* Simplify driver code by providing wrappers to those methods:
bus_set_resource(dev, type, rid, start, count);
bus_get_resource(dev, type, rid, startp, countp);
bus_get_resource_start(dev, type, rid);
bus_get_resource_count(dev, type, rid);
bus_delete_resource(dev, type, rid);
* Delete isa_get_rsrc and use bus_get_resource_start instead.
* Fix a stupid typo in isa_alloc_resource reported by Takahashi
Yoshihiro <nyan@FreeBSD.org>.
* Print a diagnostic message if we can't assign resources to a PnP
device.
* Change device_print_prettyname() so that it doesn't print
"(no driver assigned)-1" for anonymous devices.
- Move intrhook stuff into kernel.h
- Remove all occurrences of #device <device.h>
- Add kernel.h were necessary (nowhere)
- delete device.h
This file contained the structures for cfdata (old style config) and is no
longer used. It was included by most drivers.
It confuses the remote debugger as the definition of 'struct device' in
device.h is found before the one in bus_private.h.
Turn on the 'new' if_ep driver which supports:
ISA 3c509
MCA 3c529
EISA 3c579
PCCARD 3c589
I think all we're missing is support for the VME bus and S-100 bus
Etherlink III cards.
The new code has been tested by a number of people and all the important
bits work. I've not been able to test the EISA code but will do so once
my hardware arrives. Since I've changed nothing in the EISA code I suspect
it will perform the same manner as before.
Future changes involve whacking the ISA and PCCARD front ends to use
newbus and to convert the driver to bus_space and make it use ifmedia.
This is the first working network driver that supports MCA bus devices btw.
Enjoy.
work. Be more verbose when one cannot allocate IRQ, et al since this
is a common configuration problem. The cards have the IRQ soft wired
into their BIOS and do not try to do collision detection. This can
cause problems when this IRQ is the same as another card/device.
The PNP hasn't been tested. My PNP board is in a deployed system.
I'll sneak in testing of it sometime later. I've been able to mount
the 3.3R cdrom that arrived today and access files off it.
Submitted by: dfr
have been there in the first place. A GENERIC kernel shrinks almost 1k.
Add a slightly different safetybelt under nostop for tty drivers.
Add some missing FreeBSD tags
fields in struct cdevsw:
d_stop moved to struct tty.
d_reset already unused.
d_devtotty linkage now provided by dev_t->si_tty.
These fields will be removed from struct cdevsw together with
d_params and d_maxio Real Soon Now.
The changes in this patch consist of:
initialize dev->si_tty in *_open()
initialize tty->t_stop
remove devtotty functions
rename ttpoll to ttypoll
a few adjustments to these changes in the generic code
a bump of __FreeBSD_version
add a couple of FreeBSD tags
This means that we will not have to have a bpf and a non-bpf version
of our driver modules.
This does not open any security hole, because the bpf core isn't loadable
The drivers left unchanged are the "cross platform" drivers where the respective
maintainers are urged to DTRT, whatever that may be.
Add a couple of missing FreeBSD tags.
for you to be told there was an error [during verbose boot].
I poked him for the fix, he poked me to get it committed.
Submitted by: Jason Young <doogie@anet-stl.com>
there are stubs compiled into the kernel if BPF support is not enabled,
there aren't any problems with unresolved symbols. The modules in /modules
are compiled with BPF support enabled anyway, so the most this will do is
bloat GENERIC a little.
users have suffered from this breakage, w/o commitment from someone that
they would fix the problems.
This effectively backs out revs 1.{157-160}. It does however fix the
build problem that caused 1.157 to be committed.
If the changes from rev 1.156-1.160 can't be fully tested by the
committer, may I offer posting a diff in the freebsd-current mailing
list for broader testing before inflicting this breakage again.
1) Reworked the probe routine
2) Addition of the 574B's product ID.
3) Added useful info when booting verbosely.
Submitted by: Jason Young <doogie@anet-stl.com>
warnings caused by the arg having the wrong type (not const enough).
The arg was also wrong (a full name instead of a short one) for calls
from from subr_diskmbr.c and pc98/diskslice_machdep.c.
Doug Rabson's work, with a few tweaks from Warner Losh and I. There are
still some quirks to resolve, but the old driver is presently breaking
the build.
`ED_P1_MAR + i' and `ED_P1_PAR + i', respectively.
- convert ED_PC_RESET and ED_PC_MISC into relative offset from
ED_PC_ASIC_OFFSET (those macros are not used in current source).
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
the new PnP code. Since the bulk of the driver changes are not being
committed at this time, it will not affect the driver. The code is being
committed early to allow others synchronise changes.
new system is integrated with the ISA bus code more cleanly and allows
the future addition of more enumerators such as PnPBIOS and ACPI.
This commit also enables the new pcm driver since it is somewhat tied to
the new PnP code.
Remove WD formatting code which has never worked in 386bsd or FreeBSD.
Remove DIOCSSTEP and DIOCSRETRIES ioctls as well, they belong in
history, along with the SMD disks.
OK'ed by: bde
aligned. If I recall correctly, this is to ensure apic_imen can be
accessed in a single bus cycle. Also, use TEXT_ALIGN rather than a
.align 2 (which means 2 byte align on ELF and 4 byte align on a.out)
Diskslice/label code not yet handled.
Vinum, i4b, alpha, pc98 not dealt with (left to respective Maintainers)
Add the correct hook for devfs to kern_conf.c
The net result of this excercise is that a lot less files depends on DEVFS,
and devtoname() gets more sensible output in many cases.
A few drivers had minor additional cleanups performed relating to cdevsw
registration.
A few drivers don't register a cdevsw{} anymore, but only use make_dev().
