AR9462/AR9565.
This and some upcoming changes to the HAL for these chips should
address some of the signal sensitivity reported by users.
Tested:
* AR9462 (WB222), STA mode
Obtained from: Linux ath9k
AR9565 (Aphrodite.) These need to use the MCI routines, not
the legacy 2-wire / 3-wire bluetooth coexistence methods.
Tested:
* AR9462 (WB222); STA mode
images into the kernel as currently included into iwn6000g2{a,b}fw.ko
and delete the old files, missed in r254199 and r259135 respectively.
MFC after: 3 days
These variants have a few differences from the default AR9485 NIC,
namely:
* a non-default antenna switch config;
* slightly different RX gain table setup;
* an external XLNA hooked up to a GPIO pin;
* (and not yet done) RSSI threshold differences when
doing slow diversity.
To make this possible:
* Add the PCI device list from Linux ath9k, complete with vendor and
sub-vendor IDs for various things to be enabled;
* .. and until FreeBSD learns about a PCI device list like this,
write a search function inspired by the USB device enumeration code;
* add HAL_OPS_CONFIG to the HAL attach methods; the HAL can use this
to initialise its local driver parameters upon attach;
* copy these parameters over in the AR9300 HAL;
* don't default to override the antenna switch - only do it for
the chips that require it;
* I brought over ar9300_attenuation_apply() from ath9k which is cleaner
and easier to read for this particular NIC.
This is a work in progress. I'm worried that there's some post-AR9380
NIC out there which doesn't work without the antenna override set as
I currently haven't implemented bluetooth coexistence for the AR9380
and later HAL. But I'd rather have this code in the tree and fix it
up before 11.0-RELEASE happens versus having a set of newer NICs
in laptops be effectively RX deaf.
Tested:
* AR9380 (STA)
* AR9485 CUS198 (STA)
Obtained from: Qualcomm Atheros, Linux ath9k
The firmware is from the Linux firmware git repository; the intel
licence is the same as other firmware blobs.
Tested: iwn1: <Intel Centrino Wireless-N 100> mem 0xf4800000-0xf4801fff irq 19 at device 0.0 on pci5
If powersave is enabled and there are any transitions to network
or full sleep - even if they're pretty damned brief - eventually
something messes up somewhere and the bus glue between the AR9331
SoC and the AR9331 wifi stops working. It shows up as stuck DMA
and LOCAL_TIMEOUT interrupts.
Both ath9k and the reference driver does a full chip reset if things
get stuck.
So:
* teach the AR9330 HAL about the force_full_reset option I added a
couple of years ago;
* if the chip is currently in full-sleep, do a full-reset;
* if TX DMA and/or RX DMA are still enabled (eg, they did get
stuck during reset) then do a full-reset.
Tested:
* AR9331 SoC, STA mode
This includes:
o All directories named *ia64*
o All files named *ia64*
o All ia64-specific code guarded by __ia64__
o All ia64-specific makefile logic
o Mention of ia64 in comments and documentation
This excludes:
o Everything under contrib/
o Everything under crypto/
o sys/xen/interface
o sys/sys/elf_common.h
Discussed at: BSDcan
This seems to probe/attach as an AR9485 and thus nothing else besides
adding the device id seems to be required.
ath0: <Atheros AR1111> mem 0xf4800000-0xf487ffff irq 19 at device 0.0 on pci5
ath0: [HT] enabling HT modes
ath0: [HT] enabling short-GI in 20MHz mode
ath0: [HT] 1 stream STBC receive enabled
ath0: [HT] 1 RX streams; 1 TX streams
ath0: AR9485 mac 576.1 RF5110 phy 1926.8
ath0: 2GHz radio: 0x0000; 5GHz radio: 0x0000
The NIC I have here is a 1 antenna, 2GHz only device.
Thankyou to Jim Thompson <jim@netgate.com> for the AR1111 NIC.
Tested:
* AR1111 (pretending not to be an AR9485, but failing miserably);
STA mode with powersave.
Relnotes: yes
Sponsored by: Netgate
This driver is based on Linux 3.8 and a previous effort by kan@.
More informations about this project can be found on the FreeBSD wiki:
https://wiki.freebsd.org/AMD_GPU
The driver is split into:
sys/dev/drm2:
The driver sources.
sys/modules/drm2/radeonkmw:
The driver main kernel module's Makefile.
sys/modules/drm2/radeonkmsfw:
All firmware kernel module Makefiles. There's one directory and one
Makefile for each firmware.
sys/contrib/dev/drm2/radeonkmsfw:
All firmware binary sources.
tools/tools/drm/radeon
Tools to update firmwares or regenerate some headers.
Merging the driver to FreeBSD 9.x may be possible but not a priority for
now.
Help from: kib@, kan@
Tested by: avg@, kwm@, ray@,
Alexander Yerenkow <yerenkow@gmail.com>,
Anders Bolt-Evensen <andersbo87@me.com>,
Denis Djubajlo <stdedjub@googlemail.com>,
J.R. Oldroyd <fbsd@opal.com>,
Mikaël Urankar <mikael.urankar@gmail.com>,
Pierre-Emmanuel Pédron <pepcitron@gmail.com>,
Sam Fourman Jr. <sfourman@gmail.com>,
Wade <wade-is-great@live.com>,
(probably other I forgot...)
HW donations: kyzh, Yakaz
When building AR933x test images, I'd like to only build only the ar9300
HAL. To do this, it needs to supply an RF linker entry or it won't compile.
Tested:
* AR933x test builds
NICs which have bluetooth coexistence enabled.
The WB225 NIC has the common antenna switch configuration set to 0x0 which
disables all external switch bit setting. This obviously won't work when
doing coexistence.
This value is a magic value from the windows .inf files. It _looks_ right
but I haven't yet verified it - unfortunately my AR9285+AR3012 BT combo
has an earlier BT device which doesn't actually _have_ firmware on it.
So I have to fix ath3kfw to handle loading in firmware into the newer
NICs before I can finish testing this.
This may not hold true for CUS198, which is another custom AR9485 board.
