PMAP_DIAGNOSTIC was eliminated from amd64/i386, and, in fact, the
non-MIPS parts of the kernel, several years ago. Any of the interesting
checks were turned into KASSERT()s. Basically, the motivation was that
lots of people run with INVARIANTS but no one runs with DIAGNOSTIC.
panic strings needn't and shouldn't have a terminating newline.
Finally, there is one functional change. The sched_pin() in
pmap_remove_pages() is an artifact of the way we temporarily map page
table pages on i386. (The mappings are processor private. We don't do
a system-wide shootdown.) It isn't needed by MIPS.
Tested by: jchandra
Submitted by: alc
1. On n64, use XKPHYS to map page table pages instead of KSEG0. Maintain
just one freepages list on n64.
The changes are mainly to introduce MIPS_PHYS_TO_DIRECT(pa),
MIPS_DIRECT_TO_PHYS(), which will use KSEG0 in 32 bit compilation
and XKPHYS in 64 bit compilation.
2. Change macro based PMAP_LMEM_MAP1(), PMAP_LMEM_MAP2(), PMAP_LMEM_UNMAP()
to inline functions.
3. Introduce MIPS_DIRECT_MAPPABLE(pa), which will further reduce the cases
in which we will need to have a special case for 64 bit compilation.
4. Update CP0 hazard definitions for CPU_RMI - the cpu does not need any
nops
Reviewed by: neel
In particular, provide pagesize and pagesizes array, the canary value
for SSP use, number of host CPUs and osreldate.
Tested by: marius (sparc64)
MFC after: 1 month
1. Move dirty bit emulation code that is duplicted for kernel and user
in trap.c to a function pmap_emulate_modified() in pmap.c.
2. While doing dirty bit emulation, it is not necessary to update the
TLB entry on all CPUs using smp_rendezvous(), we can just update the
TLB entry on the current CPU, and let the other CPUs update their TLB
entry lazily if they get an exception.
Reviewed by: alc, neel
r211130 in favor of this more general fix.
This fixes a compilation error for mips 64-bit little endian build.
libexec/rtld-elf/mips/reloc.c:196: warning: right shift count >= width of type
Suggested by: stefanf, jchandra, bde
IPI to a specific CPU by its cpuid. Replace calls to ipi_selected() that
constructed a mask for a single CPU with calls to ipi_cpu() instead. This
will matter more in the future when we transition from cpumask_t to
cpuset_t for CPU masks in which case building a CPU mask is more expensive.
Submitted by: peter, sbruno
Reviewed by: rookie
Obtained from: Yahoo! (x86)
MFC after: 1 month
pmap_page_wired_mappings() counts the number of pv entries for the
specified page that have the pv entry wired flag set to TRUE.
pmap_enter() correctly initializes this flag. However,
pmap_change_wiring() doesn't update the corresponding pv entry flag,
only the PTE. So, the count returned by pmap_page_wired_mappings()
will sometimes be wrong.
In the short term, the best fix would be to eliminate the pv entry
flag and use only the PTE. That flag is wasting non-trivial memory.
Remove pv_wired flag, and use PTE flag to count the wired mappings.
Reviewed by: alc
- 32 bit compilation will still use old 2 level page tables
- re-arrange pmap code so that adding another level is easier
- pmap code for 3 level page tables for n64
- update TLB handler to traverse 3 levels in n64
Reviewed by: jmallett
now it uses a very dumb first-touch allocation policy. This will change in
the future.
- Each architecture indicates the maximum number of supported memory domains
via a new VM_NDOMAIN parameter in <machine/vmparam.h>.
- Each cpu now has a PCPU_GET(domain) member to indicate the memory domain
a CPU belongs to. Domain values are dense and numbered from 0.
- When a platform supports multiple domains, the default freelist
(VM_FREELIST_DEFAULT) is split up into N freelists, one for each domain.
The MD code is required to populate an array of mem_affinity structures.
Each entry in the array defines a range of memory (start and end) and a
domain for the range. Multiple entries may be present for a single
domain. The list is terminated by an entry where all fields are zero.
This array of structures is used to split up phys_avail[] regions that
fall in VM_FREELIST_DEFAULT into per-domain freelists.
- Each memory domain has a separate lookup-array of freelists that is
used when fulfulling a physical memory allocation. Right now the
per-domain freelists are listed in a round-robin order for each domain.
In the future a table such as the ACPI SLIT table may be used to order
the per-domain lookup lists based on the penalty for each memory domain
relative to a specific domain. The lookup lists may be examined via a
new vm.phys.lookup_lists sysctl.
- The first-touch policy is implemented by using PCPU_GET(domain) to
pick a lookup list when allocating memory.
Reviewed by: alc
alc@.
The UMA zone based allocation is replaced by a scheme that creates
a new free page list for the KSEG0 region, and a new function
in sys/vm that allocates pages from a specific free page list.
This also fixes a race condition introduced by the UMA based page table
page allocation code. Dropping the page queue and pmap locks before
the call to uma_zfree, and re-acquiring them afterwards will introduce
a race condtion(noted by alc@).
The changes are :
- Revert the earlier changes in MIPS pmap.c that added UMA zone for
page table pages.
- Add a new freelist VM_FREELIST_HIGHMEM to MIPS vmparam.h for memory that
is not directly mapped (in 32bit kernel). Normal page allocations will first
try the HIGHMEM freelist and then the default(direct mapped) freelist.
- Add a new function 'vm_page_t vm_page_alloc_freelist(int flind, int
order, int req)' to vm/vm_page.c to allocate a page from a specified
freelist. The MIPS page table pages will be allocated using this function
from the freelist containing direct mapped pages.
- Move the page initialization code from vm_phys_alloc_contig() to a
new function vm_page_alloc_init(), and use this function to initialize
pages in vm_page_alloc_freelist() too.
- Split the function vm_phys_alloc_pages(int pool, int order) to create
vm_phys_alloc_freelist_pages(int flind, int pool, int order), and use
this function from both vm_page_alloc_freelist() and vm_phys_alloc_pages().
Reviewed by: alc
library:
o) Increase inline unit / large function growth limits for MIPS to accommodate
the needs of the Simple Executive, which uses a shocking amount of inlining.
o) Remove TARGET_OCTEON and use CPU_CNMIPS to do things required by cnMIPS and
the Octeon SoC.
o) Add OCTEON_VENDOR_LANNER to use Lanner's allocation of vendor-specific
board numbers, specifically to support the MR320.
o) Add OCTEON_BOARD_CAPK_0100ND to hard-wire configuration for the CAPK-0100nd,
which improperly uses an evaluation board's board number and breaks board
detection at runtime. This board is sold by Portwell as the CAM-0100.
o) Add support for the RTC available on some Octeon boards.
o) Add support for the Octeon PCI bus. Note that rman_[sg]et_virtual for IO
ports can not work unless building for n64.
o) Clean up the CompactFlash driver to use Simple Executive macros and
structures where possible (it would be advisable to use the Simple Executive
API to set the PIO mode, too, but that is not done presently.) Also use
structures from FreeBSD's ATA layer rather than structures copied from
Linux.
o) Print available Octeon SoC features on boot.
o) Add support for the Octeon timecounter.
o) Use the Simple Executive's routines rather than local copies for doing reads
and writes to 64-bit addresses and use its macros for various device
addresses rather than using local copies.
o) Rename octeon_board_real to octeon_is_simulation to reduce differences with
Cavium-provided code originally written for Linux. Also make it use the
same simplified test that the Simple Executive and Linux both use rather
than our complex one.
o) Add support for the Octeon CIU, which is the main interrupt unit, as a bus
to use normal interrupt allocation and setup routines.
o) Use the Simple Executive's bootmem facility to allocate physical memory for
the kernel, rather than assuming we know which addresses we can steal.
NB: This may reduce the amount of RAM the kernel reports you as having if
you are leaving large temporary allocations made by U-Boot allocated
when starting FreeBSD.
o) Add a port of the Cavium-provided Ethernet driver for Linux. This changes
Ethernet interface naming from rgmxN to octeN. The new driver has vast
improvements over the old one, both in performance and functionality, but
does still have some features which have not been ported entirely and there
may be unimplemented code that can be hit in everyday use. I will make
every effort to correct those as they are reported.
o) Support loading the kernel on non-contiguous cores.
o) Add very conservative support for harvesting randomness from the Octeon
random number device.
o) Turn SMP on by default.
o) Clean up the style of the Octeon kernel configurations a little and make
them compile with -march=octeon.
o) Add support for the Lanner MR320 and the CAPK-0100nd to the Simple
Executive.
o) Modify the Simple Executive to build on FreeBSD and to build without
executive-config.h or cvmx-config.h. In the future we may want to
revert part of these changes and supply executive-config.h and
cvmx-config.h and access to the options contained in those files via
kernel configuration files.
o) Modify the Simple Executive USB routines to support getting and setting
of the USB PID.
Move inappropriate stuff in cpu.h elsewhere:
{s,g}et_intr_mask -> md_var.h
num_tlbentries -> tlb.h
Remove #define clockframe trapframe and fix clock, which was the only place
this was used.
All the rest of this stuff was unused.
# we're not quite minimal yet, since we duplicate a few status register things
# here...
Inspired by: bde@
Use int32/intptr casts for exception vector names.
Define MIPS_SR_INT_MASK again
Change MIPS_XKPHYS_CCA_* to MIPS_CCA_* since we can use them in many contexts
Minor gratuitous whitespace churn
The problem with setting it there is that the last CPU to come up
wins, it seems. This also removes one more ifdef in locore.S, a noble
goal too. Since they are unused, and pollute cpu.h, remove them.
Submitted by: bde.h (cpu.h pollution)
Approved in theory by: jmallet@
Updated PTE/PDE macros from http://svn.freebsd.org/base/user/jmallett/octeon
Introduce pmap_segshift() macro, use pmap_segmap() in place of pmap_pde, and
remove pmap_pde().
Approved by: rrs (mentor)
Obtained from: jmallett@
If we save/restore the PageMask, the value set by the bootloader will
persist, and will cause problems later in TLB exception handler.
This caused a crash in AR71xx boards.
Also fixes the EntryHi mask in pte.h
Reported by: Luiz Otavio O Souza <lists.br@gmail.com>
Tested by: Luiz Otavio O Souza <lists.br@gmail.com>
Approved by: rrs (mentor)
Initial support for n32 and n64 ABIs from
http://svn.freebsd.org/base/user/jmallett/octeon
Changes are:
- syscall, exception and trap support for n32/n64 ABIs
- 64-bit address space defines
- _jmp_buf for n32/n64
- casts between registers and ptr/int updated to work on n32/n64
Approved by: rrs(mentor), jmallett
PTE flag cleanup from http://svn.freebsd.org/base/user/jmallett/octeon
- Rename PTE_xx flags to match their MIPS names
- Use the new pte_set/test/clear macros uniformly, instead of a mixture
of mips_pg_xxx(), pmap_pte_x() macros and direct access.
- Remove unused macros and defines from pte.h and pmap.c
Discussed on freebsd-mips@
Approved by: rrs(mentor), jmallett
am now able to run 32 cores ok.. but I still will hang
on buildworld with a NFS problem. I suspect I am missing
a patch for the netlogic rge driver.
JC check and see if I am missing anything except your
core-mask changes
Obtained from: JC
architecture from page queue lock to a hashed array of page locks
(based on a patch by Jeff Roberson), I've implemented page lock
support in the MI code and have only moved vm_page's hold_count
out from under page queue mutex to page lock. This changes
pmap_extract_and_hold on all pmaps.
Supported by: Bitgravity Inc.
Discussed with: alc, jeffr, and kib
o) Use <machine/asm.h> macros for register-width, etc., rather than doing it
by hand in a few more assembly files.
o) Reduce diffs between various bits of TLB refill code in exception.S and
between interrupt processing code.
o) Use PTR_* to operate on registers that are pointers (e.g. sp).
o) Add and use a macro, CLEAR_PTE_SWBITS rather than using the
mysteriously-named WIRED_SHIFT to select bits to truncate when loading PTEs.
o) Don't doubly disable interrupts by moving zero to the status register,
especially since that has the nasty side-effect of taking us out of 64-bit
mode.
o) Use CLEAR_STATUS to disable interrupts the first time.
o) Keep SR_PX set as well as SR_[KSU]X when doing exception processing. This
is the bit that determines whether 64-bit operations are allowed.
o) Don't enable interrupts until configure_final(), like most other ports.
attributes for XKPHYS.
o) Make coprocessor 0 accessor function macros for register+selector registers
take the full name so that e.g. (as done in this commit), prid selector 1
can be written through mips_wr_ebase() rather than mips_wr_prid1().
o) Allow for sign extension of 32-bit segment addresses.
o) Remove an unused MIPS-I register number.
address space for an address as aligned by the new pmap_align_tlb()
function, which is for constraints imposed by the TLB. [1]
o) Add a kmem_alloc_nofault_space() function, which acts like
kmem_alloc_nofault() but allows the caller to specify which find-space
option to use. [1]
o) Use kmem_alloc_nofault_space() with VMFS_TLB_ALIGNED_SPACE to allocate the
kernel stack address on MIPS. [1]
o) Make pmap_align_tlb() on MIPS align addresses so that they do not start on
an odd boundary within the TLB, so that they are suitable for insertion as
wired entries and do not have to share a TLB entry with another mapping,
assuming they are appropriately-sized.
o) Eliminate md_realstack now that the kstack will be appropriately-aligned on
MIPS.
o) Increase the number of guard pages to 2 so that we retain the proper
alignment of the kstack address.
Reviewed by: [1] alc
X-MFC-after: Making sure alc has not come up with a better interface.
o) Mask off PAGE_MASK bits in pmap_update_page, etc., rather than modifying the
badvaddr in trapframe. Some nearby interfaces already did this.
o) Make PTEs "unsigned int" for now, not "unsigned long" -- we are only ready
for them to be 32-bit on 64-bit platforms.
o) Rather than using pmap_segmap and calculating the offset into the page table
by hand in trap.c, use pmap_pte().
o) Remove unused quad_syscall variable in trap.c.
o) Log things for illegal instructions like we do for bad page faults.
o) Various cast cleanups related to how to print registers.
o) When logging page faults, show the page table information not just for the
program counter, but for the fault address.
o) Modify support.S to use ABI-neutral macros for operating on pointers.
o) Consistently use CALLFRAME_SIZ rather than STAND_FRAME_SIZE, etc.
o) Remove unused insque/remque functions.
o) Remove some coprocessor 0 accessor functions implemented in assembly that
are unused and have inline assembly counterparts.
o) Remove NBPG, PGOFSET and PGSHIFT. Use the standard names.
o) Remove some unused macros and move things from param.h to vmparam.h that
belong in the latter. (Actually, all of the kernel segment values, virtual
addresses, etc., belong in one place, but this is a step in the right
direction.)
ones implemented using assembly.
o) Use TRAPF_USERMODE() consistently rather than USERMODE(). Eliminate
<machine/psl.h> as a result.
o) Use intr_*() rather than *intr(), consistently.
o) Use register_t instead of u_int in some trap code.
o) Merge some more endian-related macros to machine/asm.h from NetBSD.
o) Add PTR_LI macro, which loads an address with the correct sign-extension for
a pointer.
o) Restore interrupts when bailing out due to an excessive IRQ in
nexus_setup_intr().
o) Remove unused functions from psraccess.S.
o) Enter temporary virtual entries for large memory access into the page tables
rather than simply hoping they stay resident in the TLB and we don't need to
do a refill for them.
o) Abstract out large memory mapping setup/teardown using some macros.
o) Do mips_dcache_wbinv_range() when using temporary virtual addresses just
like we do when we can use the direct map.
sparc64.
o) Use uiomove_fromphys rather than the broken fpage mechanism for /dev/mem.
o) Update sf_buf allocator to not share buffers and to do a pmap_qremove when
done with an sf_buf so as to better track valid mappings.
bit.
o) Remove some unused inlines.
o) Generate CP0 access functions for 64-bit TLB registers when building for
n64.
o) Add an inline function version of the COP0_SYNC macro.
frequency. This counter can be accessed coherently from both cores.
Use this as the preferred timecounter for the SWARM kernels.
The CP0 COUNT register is unusable as the timecounter on SMP platforms because
the COUNT registers on different CPUs are not guaranteed to be in sync.
mapped kseg0 region.
The basic idea is to use KVA from the kseg2 region for mapping page
table pages that lie beyond the direct mapped region.
The TLB miss handler can now recursively fault into the TLB invalid
handler if it dereferences a kseg2 page table page address that is not
in the TLB.
Tested by: JC (c.jayachandran@gmail.com)
- We don't need to fall back to uncacheable memory to satisfy BUS_DMA_COHERENT
requests on these CPUs.
- The bus_dmamap_sync() is a no-op for these CPUs.
A side-effect of this change is rename DMAMAP_COHERENT flag to
DMAMAP_UNCACHEABLE. This conveys the purpose of the flag more accurately.
Reviewed by: gonzo, imp
- remove unused and commented code (MIPS_BUS_SPACE_PCI, pic_usb_ack)
- use rmi_pci_bus_space for USB too (needs byteswap)
- uncomment xls_ehci.c in files.xlr
- changes to xls_ehci.c - updated with dev/usb/controller/ehci_*.c as
Obtained from: JC - c.jayachandran@gmail.com
- (cleanup) remove rmi specific 'struct mips_intrhand' - this is no
longer needed since 'struct intr_event' have all the required hooks
- add xlr_cpu_establish_hardintr, which has args for pre/post ithread
and filter hooks, so that the PCI code can add the PCI controller
interrupt ack code here
- make 'cpu_establish_hardintr' use the above function.
- (fix) change type of eirr/eimr from register_t to uint64_t. These
have to be 64bit otherwise we cannot handle interrupts from 32.
- (fix) use eimr to mask eirr before checking interrupts, so that we
will not handle masked interrupts.
Obtained from: C. Jayachandran - c.jayachandran@gmail.com
The platform that supports SMP currently is a SWARM with a dual-core Sibyte
processor. The kernel config file to use is SWARM_SMP.
Reviewed by: imp, rrs
The basic idea is to use a the same virtual address as a window onto
distinct physical memory locations - one per processor. The physical
address that you access through this mapping depends on which cpu you
are currently executing on. We can now use the same virtual address
on any processor to access its per-cpu area.
The details are:
- The virtual address for 'struct pcpu *pcpup' is obtained by
stealing 2 pages worth of KVA in pmap_bootstrap().
- The mapping from the constant virtual address to a distinct
physical page is done in cpu_pcpu_init() through a wired TLB entry.
- A side-effect of this is that we reserve 2 pages worth of memory
for the pcpu but in reality it needs much less than that. The unused
memory is now used as the boot stack for the BSP and APs.
Remove SMP-specific bits from locore.S. The plan is to use a separate
mpboot.S for AP bootstrap.
Discussed on: freebsd-mips
Approved by: imp (mentor)
through fork_trampoline.
This was caused because we were clearing the SR_INT_IE and setting
SR_EXL bits of the status register at the same time. This meant
that if an interrupt happened while this MTC0 was making its way
through the pipeline the exception processing would see the
status register with SR_EXL bit set. This in turn would mean that
the COP_0_EXC_PC would not be updated so the return from exception
would be to an incorrect address.
It is easy to verify this fix by a program that forks in a loop
and the child just exits:
while (1) {
pid_t pid = vfork();
if (pid == 0)
_exit(0);
if (pid != -1)
waitpid(pid, NULL, 0);
}
Also remove two instances where we set SR_EXL bit gratuitously in exception.S.
Approved by: imp (mentor)
available for use. All data below this address considered to be used
by kernel. Along with kernel own data it might be symbol tables
prepeared by trampoline code, boot loader service data passed for
further analysis by kernel, etc... By default kernel_kseg0_end points
to the end of loaded kernel.
- Introduce mips_postboot_fixup function. It checks for symbol information
copied by ELF trampoline and passes it to KDB
r201881 | imp | 2010-01-08 20:08:22 -0700 (Fri, 08 Jan 2010) | 3 lines
Rename mips_pcpu_init to mips_pcpu0_init since it applies only to the
BSP. Provide a missing prototype.
r200343 | imp | 2009-12-09 18:44:11 -0700 (Wed, 09 Dec 2009) | 4 lines
Get the sense of this right. We use uintpr_t for bus_addr_t when
we're building everything except octeon && 32-bit. As note before, we
need a clearner way, but at least now the hack is right.
r199760 | imp | 2009-11-24 10:15:22 -0700 (Tue, 24 Nov 2009) | 2 lines
Add in Cavium's CID. Report what the unknown CID is.
r199754 | imp | 2009-11-24 09:32:31 -0700 (Tue, 24 Nov 2009) | 6 lines
Include opt_cputype.h for all .c and .S files referencing TARGET_OCTEON.
Spell ld script name right.
r199599 | imp | 2009-11-20 09:32:26 -0700 (Fri, 20 Nov 2009) | 2 lines
Another kludge for 64-bit bus_addr_t with 32-bit pointers...
r199496 | gonzo | 2009-11-18 15:52:05 -0700 (Wed, 18 Nov 2009) | 5 lines
- Add cpu_init_interrupts function that is supposed to
prepeare stuff required for spinning out interrupts later
- Add API for managing intrcnt/intrnames arrays
- Some minor style(9) fixes
r198958 | rrs | 2009-11-05 11:15:47 -0700 (Thu, 05 Nov 2009) | 2 lines
For XLR adds extern for its bus space routines
r198669 | rrs | 2009-10-30 02:53:11 -0600 (Fri, 30 Oct 2009) | 5 lines
With this commit our friend RMI will now compile. I have
not tested it and the chances of it running yet are about
ZERO.. but it will now compile. The hard part now begins,
making it run ;-)
r198666 | imp | 2009-10-29 18:37:50 -0600 (Thu, 29 Oct 2009) | 2 lines
Add some newer MIPS CO cores.
r198665 | imp | 2009-10-29 18:37:04 -0600 (Thu, 29 Oct 2009) | 4 lines
db_expr_t is really closer to a register_t.
Submitted by: bde@
r198531 | gonzo | 2009-10-27 18:01:20 -0600 (Tue, 27 Oct 2009) | 3 lines
- Remove bunch of declared but not defined cach-related variables
- Add mips_picache_linesize and mips_pdcache_linesize variables
r198354 | neel | 2009-10-21 20:51:31 -0600 (Wed, 21 Oct 2009) | 9 lines
Get rid of the hardcoded constants to define cacheable memory:
SDRAM_ADDR_START, SDRAM_ADDR_END and SDRAM_MEM_SIZE
Instead we now keep a copy of the memory regions enumerated by
platform-specific code and use that to determine whether an address
is cacheable or not.
r198310 | gonzo | 2009-10-20 17:13:08 -0600 (Tue, 20 Oct 2009) | 5 lines
- Commit missing part of "bt" fix: store PC register in pcb_context struct
in cpu_switch and use it in stack_trace function later. pcb_regs contains
state of the process stored by exception handler and therefor is not
valid for sleeping processes.
r198207 | imp | 2009-10-18 08:57:04 -0600 (Sun, 18 Oct 2009) | 2 lines
Undo spamage of last MFC.
r198206 | imp | 2009-10-18 08:56:33 -0600 (Sun, 18 Oct 2009) | 3 lines
_ALIGN has to return u_long, since pointers don't fit into u_int in
64-bit mips.
r198182 | gonzo | 2009-10-16 18:22:07 -0600 (Fri, 16 Oct 2009) | 11 lines
- Use PC/RA/SP values as arguments for stacktrace_subr instead of trapframe.
Context info could be obtained from other sources (see below) no only from
td_pcb field
- Do not show a0..a3 values unless they're obtained from the stack. These
are only confirmed values.
- Fix bt command in DDB. Previous implementation used thread's trapframe
structure as a source info for trace unwinding, but this structure
is filled only when exception occurs. Valid register values for sleeping
processes are in pcb_context array. For curthread use pc/sp/ra for current
frame
r198181 | gonzo | 2009-10-16 16:52:18 -0600 (Fri, 16 Oct 2009) | 2 lines
- Get rid of label_t. It came from NetBSD and was used only in one place
r198154 | rrs | 2009-10-15 15:03:32 -0600 (Thu, 15 Oct 2009) | 10 lines
Does 4 things:
1) Adds future RMI directories
2) Places intr_machdep.c in specfic files.arch pointing to the generic
intr_machdep.c. This allows us to have an architecture dependant
intr_machdep.c (which we will need for RMI) in the machine specific
directory
3) removes intr_machdep.c from files.mips
4) Adds some TARGET_XLR_XLS ifdef's for the machine specific intra_machdep.h. We
may need to look at finding a better place to put this. But first I want to
get this thing compiling.
r198066 | gonzo | 2009-10-13 19:43:53 -0600 (Tue, 13 Oct 2009) | 5 lines
- Move stack tracing function to db_trace.c
- Axe unused extern MipsXXX declarations
- Move all declarations for functions in exceptions.S/swtch.S
from trap.c to respective headers
r197685 | gonzo | 2009-10-01 14:05:36 -0600 (Thu, 01 Oct 2009) | 2 lines
- Sync caches properly when dealing with sf_buf
r196215 | imp | 2009-08-14 10:15:18 -0600 (Fri, 14 Aug 2009) | 6 lines
(u_int) is the wrong type here. Use unsigned long instead, even
though that's only less wrong...
r196199 | imp | 2009-08-13 13:47:13 -0600 (Thu, 13 Aug 2009) | 7 lines
Use unsigned long instead of unsigned for the integer casts here. The
former works for both ILP32 and LP64 programming models, while the
latter fails LP64.
r196089 | gonzo | 2009-08-09 19:49:59 -0600 (Sun, 09 Aug 2009) | 4 lines
- Make i/d cache size field 32-bit to prevent overflow
Submited by: Neelkanth Natu
r195582 | imp | 2009-07-10 13:07:07 -0600 (Fri, 10 Jul 2009) | 2 lines
fix prototype for MipsEmulateBranch.
r195581 | imp | 2009-07-10 13:06:43 -0600 (Fri, 10 Jul 2009) | 2 lines
Better definitions for a few types for n32/n64.
r195580 | imp | 2009-07-10 13:06:15 -0600 (Fri, 10 Jul 2009) | 5 lines
Fixed aligned macros...
r195478 | gonzo | 2009-07-08 16:28:36 -0600 (Wed, 08 Jul 2009) | 5 lines
- Port busdma code from FreeBSD/arm. This is more mature version
that takes into account all limitation to DMA memory (boundaries,
alignment) and implements bounce pages.
- Add BUS_DMASYNC_POSTREAD case to bus_dmamap_sync_buf
r195440 | imp | 2009-07-08 00:01:37 -0600 (Wed, 08 Jul 2009) | 2 lines
Fix atomic_store_64 prototype for 64-bit systems.
r195392 | imp | 2009-07-05 20:27:03 -0600 (Sun, 05 Jul 2009) | 3 lines
The MCOUNT macro isn't going to work in 64-bit mode. Add a note to
this effect.
r195391 | imp | 2009-07-05 20:22:51 -0600 (Sun, 05 Jul 2009) | 3 lines
Provide a macro for PTR_ADDU as well. We may need to implement this
differently for N32... Use PTR_ADDU in DO_AST macro.
r195390 | imp | 2009-07-05 20:22:06 -0600 (Sun, 05 Jul 2009) | 4 lines
Change the addu here to daddu.
addu paranoina prodded by: jmallet@
r195382 | imp | 2009-07-05 15:16:26 -0600 (Sun, 05 Jul 2009) | 5 lines
addu and subu are special. We need to use daddu and dsubu here to get
proper behavior.
Submitted by: jmallet@
r195370 | imp | 2009-07-05 09:20:16 -0600 (Sun, 05 Jul 2009) | 6 lines
The SB1 has cohernet memory, so add it.
Also, Maxmem is better as a long.
Submitted by: Neelkanth Natu
r195369 | imp | 2009-07-05 09:19:28 -0600 (Sun, 05 Jul 2009) | 4 lines
The SB1 needs a special value for the cache field of the pte.
Submitted by: Neelkanth Natu
r195368 | imp | 2009-07-05 09:18:06 -0600 (Sun, 05 Jul 2009) | 2 lines
compute the areas to save registers in for 64-bit access correctly.
r195367 | imp | 2009-07-05 09:17:11 -0600 (Sun, 05 Jul 2009) | 3 lines
First cut at 64-bit types. not 100% sure these are all correct for
N32 ABI.
r195366 | imp | 2009-07-05 09:16:27 -0600 (Sun, 05 Jul 2009) | 3 lines
Trim unreferenced goo. SDRAM likely should be next, but it is still
referenced.
r195365 | imp | 2009-07-05 09:13:24 -0600 (Sun, 05 Jul 2009) | 9 lines
First cut at atomics for 64-bit machines and SMP machines.
# Note: Cavium provided a port that has atomics similar to these, but
# that does a syncw; sync; atomic; sync; syncw where we just do the classic
# mips 'atomic' operation (eg ll; frob; sc). It is unclear to me why
# the extra is needed. Since my initial target is one core, I'll defer
# investigation until I bring up multiple cores. syncw is an octeon specific
# instruction.
r195359 | imp | 2009-07-05 02:14:00 -0600 (Sun, 05 Jul 2009) | 4 lines
Bring in cdefs.h from NetBSD to define ABI goo.
Obtained from: NetBSD
r195358 | imp | 2009-07-05 02:13:19 -0600 (Sun, 05 Jul 2009) | 4 lines
Pull in machine/cdefs.h for the ABI definitions. Provide a PTR_LA,
ala sgi, and use it in preference to a bare 'la' so that it gets
translated to a 'dla' for the 64-bit pointer ABIs.
r195357 | imp | 2009-07-05 01:01:34 -0600 (Sun, 05 Jul 2009) | 2 lines
Use uintptr_t rather than unsigned here for 64-bit correctness.
r195356 | imp | 2009-07-05 01:00:51 -0600 (Sun, 05 Jul 2009) | 6 lines
Define __ELF_WORD_SIZE appropriately for n64. Note for N32 I believe
this is correct. While registers are 64-bit, n32 is a 32-bit ABI and
lives in a 32-bit world (with explicit 64-bit registers, however).
Change an 8, which was 4 + 4 or sizeof(int) + SZREG to be a simple '4
+ SZREG' to reflect the actual offset of the structure in question.
r195355 | imp | 2009-07-05 00:56:51 -0600 (Sun, 05 Jul 2009) | 7 lines
(1) Use uintptr_t in preference to unsigned. The latter isn't right for
64-bit case, while the former is.
(2) include a SB1 specific coherency mapping
Submitted by: Neelkanth Nath (2)
r195352 | imp | 2009-07-05 00:44:37 -0600 (Sun, 05 Jul 2009) | 3 lines
db_expr_t should be a intptr_t, not an int. These expressions can be
addresses or numbers, and that's a intptr_t if I ever saw one.
r195351 | imp | 2009-07-05 00:43:01 -0600 (Sun, 05 Jul 2009) | 4 lines
Define COP0_SYNC for SB1 CPU.
Submitted by: Neelkanth Natu
r195350 | imp | 2009-07-05 00:39:37 -0600 (Sun, 05 Jul 2009) | 7 lines
Switch to ABI agnostic ta0-ta3. Provide defs for this in the right
places. Provide n32/n64 register name defintions. This should have
no effect for the O32 builds that everybody else uses, but should help
make N64 builds possible (lots of other changes are needed for that).
Obtained from: NetBSD (for the regdef.h changes)
r195128 | gonzo | 2009-06-27 17:27:41 -0600 (Sat, 27 Jun 2009) | 4 lines
- Add support for handling TLS area address in kernel space.
From the userland point of view get/set operations are
performed using sysarch(2) call.
r195076 | gonzo | 2009-06-26 13:54:06 -0600 (Fri, 26 Jun 2009) | 2 lines
- Add guards to ensure that these files are included only once
r194469 | gonzo | 2009-06-18 22:43:49 -0600 (Thu, 18 Jun 2009) | 16 lines
- Mark temp variable as "earlyclobber" in assembler inline in
atomic_fetchadd_32. Without it gcc would use it as input
register for v and sometimes generate following code for
function call like atomic_fetchadd_32(&(fp)->f_count, -1):
801238b4: 2402ffff li v0,-1
801238b8: c2230018 ll v1,24(s1)
801238bc: 00431021 addu v0,v0,v1
801238c0: e2220018 sc v0,24(s1)
801238c4: 1040fffc beqz v0,801238b8 <dupfdopen+0x2e8>
801238c8: 00000000 nop
Which is definitly wrong because if sc fails v0 is set to 0
and previous value of -1 is overriden hence whole operation
turns to bogus
r194164 | imp | 2009-06-14 00:14:25 -0600 (Sun, 14 Jun 2009) | 3 lines
bye bye. This is no longer referenced, but much code from it will
resurface for a bus-space implementation.
r194160 | imp | 2009-06-14 00:10:36 -0600 (Sun, 14 Jun 2009) | 3 lines
Cavium-specific goo is no longer necessary here. Of course, I now
have to write a bus space for cavium, but that shouldn't be too hard.
r194157 | imp | 2009-06-14 00:01:46 -0600 (Sun, 14 Jun 2009) | 2 lines
Move this to a more approrpiate plae.
r194156 | imp | 2009-06-13 23:29:13 -0600 (Sat, 13 Jun 2009) | 2 lines
Bring this in from the cavium port.
r193487 | gonzo | 2009-06-05 02:37:11 -0600 (Fri, 05 Jun 2009) | 2 lines
- Use restoreintr instead of enableint while accessing pcpu in DO_AST
r192864 | gonzo | 2009-05-26 16:40:12 -0600 (Tue, 26 May 2009) | 4 lines
- Replace CPU_NOFPU and SOFTFLOAT options with CPU_FPU. By default
we assume that there is no FPU, because majority of SoC does
not have it.
r192817 | gonzo | 2009-05-26 10:35:05 -0600 (Tue, 26 May 2009) | 2 lines
- Add type cast for atomic_cmpset_acq_ptr arguments
r192792 | gonzo | 2009-05-26 00:01:17 -0600 (Tue, 26 May 2009) | 2 lines
- Remove now unused NetBSDism intr.h
r192177 | gonzo | 2009-05-15 20:39:13 -0600 (Fri, 15 May 2009) | 4 lines
- Add MIPS_IS_KSEG0_ADDR, MIPS_IS_KSEG1_ADDR and MIPS_IS_VALID_PTR
macroses thet check if address belongs to KSEG0, KSEG1 or both
of them respectively.
r191589 | gonzo | 2009-04-27 13:18:55 -0600 (Mon, 27 Apr 2009) | 3 lines
- Cast argument to proper type in order to avoid warnings like
"shift value is too large for given type"
r191577 | gonzo | 2009-04-27 12:29:59 -0600 (Mon, 27 Apr 2009) | 4 lines
- Use naming convention the same as MIPS spec does: eliminate _sel1 sufix
and just use selector number. e.g. mips_rd_config_sel1 -> mips_rd_config1
- Add WatchHi/WatchLo accessors for selctors 1..3 (for debug purposes)
r191451 | gonzo | 2009-04-23 22:17:21 -0600 (Thu, 23 Apr 2009) | 4 lines
- Define accessor functions for CP0 Config(16) register selects 1, 2, 3.
Content of these registers is defined in MIPS spec and can be used
for obtaining info about CPU capabilities.
r191282 | gonzo | 2009-04-19 16:02:14 -0600 (Sun, 19 Apr 2009) | 3 lines
- Make mips_bus_space_generic be of type bus_space_tag_t instead of
struct bus_space and update all relevant places.
r191084 | gonzo | 2009-04-14 20:28:26 -0600 (Tue, 14 Apr 2009) | 6 lines
Use FreeBSD/arm approach for handling bus space access: space tag is a pointer
to bus_space structure that defines access methods and hence every bus can
define own accessors. Default space is mips_bus_space_generic. It's a simple
interface to physical memory, values are read with regard to host system
byte order.
r195128 | gonzo | 2009-06-27 17:27:41 -0600 (Sat, 27 Jun 2009) | 4 lines
- Add support for handling TLS area address in kernel space.
From the userland point of view get/set operations are
performed using sysarch(2) call.
