For the most of chips (except anscient ones) port handlers have no relation
to port IDs. In such situation old code scanning first 125 handlers was
quite naive. Instead of doing that, send to chip single request to get full
list of port handlers available on specific virtual port and scan only them.
Old code had problems with case of several virtual ports enabled, when port
handlers allocated from global address space could easily go above 125.
This change was successfully tested on 23xx, 24xx and 25xx chips in loop
mode with 4 virtual initiator ports, each seing 50 virtual target ports.
Now on 24xx and above chips it is really possible to simulate several
virtual FC ports with single physical one. For example, it allows to
configure several targets in ctl.conf, assign each of them to separate
virtual port, and let user to control access to them with switch zoning.
I still doubt that all problems are solved there, but at now it passes
at least basic tests.
Now 24xx and above chips support full 8-byte LUN address space.
Older FC chips may support up to 16K LUNs when firmware allows.
Tested in both initiator and target modes for 23xx, 24xx and 25xx.
Aside from cleaner and more consistent code, this allows ports to be both
target and initiator same time, and easily switch from any role to any.
Sponsored by: iXsystems, Inc.
FreeBSD never had limitation on number of target IDs, and there is no
any other requirement to allocate them densely. Since slots of port
database already populated just sequentially, there is no much need
for another indirection to allocate sequentially too.
It is odd that driver first tries to generate synthetic WWNN based on
WWPN starting from 2, but then refuses to use it. If we don't trust
generated WWNN, we should probably not generate it. Same time this
limitation prevents potentially valid WWNN setting by user.
The newer boards don't have the response field that indicates
whether the SCSI status byte is present. You have to just look to
see whether it is non-zero.
The code was looking to see whether the sense length was valid
before propagating the SCSI status byte (and sense information) up
the stack. With a status like Reservation Conflict, there is no
sense information, only the SCSI status byte. So it wasn't getting
correctly returned.
isp.c:
In isp_intr(), if we are on a 2400 or 2500 type board and
get a response, look at the actual contents of the
SCSI status value and set the RQSF_GOT_STATUS flag
accordingly so that return any SCSI status value we get. The
RQSF_GOT_SENSE flag will get set later on if there is
actual sense information returned.
Submitted by: ken
MFC after: 1 week
Sponsored by: Spectra Logic
MFSpectraBSD: 1112791 on 2015/01/15
- Process ATIO queue only if interrupt status tells so;
- Do not update queue out pointers after each processed command, do it
only once at the end of the loop.
- Remove two excessive and slow register reads from isp_intr(). Instead
of rereading value every time, assume that registers contain what we have
written there.
- Avoid sequential search through 4096 array elements when looking for
command tag. Use hash of lists to store active tags separately from free
ones and so greatly speedup the searches.
Reviewed by: mjacob
a mailbox command and which registers to copy back in when
the command completes, the bits being set need to not only
specify what bits you want to add from the default from the
table but also what bits you want *subtract* (mask) from the
default from the table.
A failing ISP2200 command pointed this out.
Much appreciation to: marius, who persisted and narrowed down what
the failure delta was, and shamed me into actually fixing it.
MFC after: 1 week
might have been enabled for them- now that we use all 32 bits of handle.
Fast Posting doesn't pass the full 32 bits.
Noticed by: Bugs in NetBSD. Only a NetBSD user might actually still use such old hardware.
MFC after: 1 week
MISC CHANGES
Add a new async event- ISP_TARGET_NOTIFY_ACK, that will guarantee
eventual delivery of a NOTIFY ACK. This is tons better than just
ignoring the return from isp_notify_ack and hoping for the best.
Clean up the lower level lun enable code to be a bit more sensible.
Fix a botch in isp_endcmd which was messing up the sense data.
Fix notify ack for SRR to use a sensible error code in the case
of a reject.
Clean up and make clear what kind of firmware we've loaded and
what capabilities it has.
-----------
FULL (252 byte) SENSE DATA
In CTIOs for the ISP, there's only a limimted amount of space
to load SENSE DATA for associated CHECK CONDITIONS (24 or 26
bytes). This makes it difficult to send full SENSE DATA that can
be up to 252 bytes.
Implement MODE 2 responses which have us build the FCP Response
in system memory which the ISP will put onto the wire directly.
On the initiator side, the same problem occurs in that a command
status response only has a limited amount of space for SENSE DATA.
This data is supplemented by status continuation responses that
the ISP pushes onto the response queue after the status response.
We now pull them all together so that full sense data can be
returned to the periph driver.
This is supported on 23XX, 24XX and 25XX cards.
This is also preparation for doing >16 byte CDBs.
-----------
FC TAPE
Implement full FC-TAPE on both initiator and target mode side. This
capability is driven by firmware loaded, board type, board NVRAM
settings, or hint configuration options to enable or disable. This
is supported for 23XX, 24XX and 25XX cards.
On the initiator side, we pretty much just have to generate a command
reference number for each command we send out. This is FCP-4 compliant
in that we do this per ITL nexus to generate the allowed 1 thru 255
CRN.
In order to support the target side of FC-TAPE, we now pay attention
to more of the PRLI word 3 parameters which will tell us whether
an initiator wants confirmed responses. While we're at it, we'll
pay attention to the initiator view too and report it.
On sending back CTIOs, we will notice whether the initiator wants
confirmed responses and we'll set up flags to do so.
If a response or data frame is lost the initiator sends us an SRR
(Sequence Retransmit Request) ELS which shows up as an SRR notify
and all outstanding CTIOs are nuked with SRR Received status. The
SRR notify contains the offset that the initiator wants us to restart
the data transfer from or to retransmit the response frame.
If the ISP driver still has the CCB around for which the data segment
or response applies, it will retransmit.
However, we typically don't know about a lost data frame until we
send the FCP Response and the initiator totes up counters for data
moved and notices missing segments. In this case we've already
completed the data CCBs already and sent themn back up to the periph
driver. Because there's no really clean mechanism yet in CAM to
handle this, a hack has been put into place to complete the CTIO
CCB with the CAM_MESSAGE_RECV status which will have a MODIFY DATA
POINTER extended message in it. The internal ISP target groks this
and ctl(8) will be modified to deal with this as well.
At any rate, the data is retransmitted and an an FCP response is
sent. The whole point here is to successfully complete a command
so that you don't have to depend on ULP (SCSI) to have to recover,
which in the case of tape is not really possible (hence the name
FC-TAPE).
Sponsored by: Spectralogic
MFC after: 1 month
not by some hint setting. Do more preparations for FC-Tape.
Clean up resource counting for 24XX or later chipsets so
we find out after EXEC_FIRMWARE what is actually supported.
Set target mode exchange count based upon whether or not
we are supporting simultaneous target/initiator mode. Clean
up some old (pre-24XX) xfwoption and zfwoption issues.
Sponsored by: Spectralogic
MFC after: 3 days
and crosschecks against firmware documentation. We now check and report
FC firmware attributes and at least are now prepared for the upper 48 bits
of f/w attributes (which are probably for the 8100 or later cards). This
involed changing how inbits and outbits are calculated for varios commands,
hopefully clearer and cleaner. This also caused me to clean up the actual
mailbox register usage. Finally, we are now unconditionally using a CRN
for initiator mode.
A longstanding issue with the 2400/2500 is that they do *not* support
a "Prefer PTP followed by loop", which explains why enabling that
caused the f/w to crash.
A slightly more invasive change is to let the firmware load entirely
drive whether multi_id support is enabled or not.
Sponsored by: Spectralogic
MFC after: 1 week
Make the default role NONE if target mode is selected. This
allows ctl(8) to switch to/from target mode via knob settings.
If we default to role 'none', this causes a reset of the
24XX f/w which then causes initiators to wake up and notice
when we come online.
Reviewed by: kdm
MFC after: 2 weeks
Sponsored by: Spectralogic
is actually broken, or needs a BIOS upgrade for 64 bit loads, but this uncovered
a couple of misplaced opcode definitions and some missing continual mbox command
cases, so might as well update them here.
We also revive loop down freezes. We also externaliz within isp
isp_prt_endcmd so something outside the core module can print
something about a command completing. Also some work in progress to
assist in handling timed out commands better.
Partially Sponsored by: Panasas
Approved by: re (kib)
MFC after: 1 month
- Allocate coherent DMA memory for the request/response queue area and
and the FC scratch area.
These changes allow isp(4) to work properly on sparc64 with usage of the
IOMMU streaming buffers enabled.
Approved by: mjacob
MFC after: 2 weeks
on debug output. Add a new platform function requirement to allow
for printing based upon the ITL nexus instead of the isp unit plus
channel, target and lun. This allows some printouts and error messages
from the core code to appear in the same format as the platform's
subsystem (in FreeBSD's case, CAM path).
MFC after: 1 week
32 bit handles. The RIO (reduced interrupt operation) and fast posting
for the parallel SCSI cards were all 16 bit handles. Furthermore,
target mode parallel SCSI only can have 16 bit handles.
Use part of a supplied patch to switch over to using 32 bit handles.
Be a bit more conservative here and only do this for parallel SCSI
for the 12160 (Ultra3) cards. There were a lot of marginal Ultra2
cards, and, frankly, few are findable now for testing.
Fix the target handle routine to only do 16 bit handles for parallel
SCSI cards. This is okay because the upper sixteen bits of the new
32 bit handles is a sequence number to help protect against duplicate
completions. This would be very unlikely to happen with parallel
SCSI target mode, and wasn't present before, so we're no worse off
than we used to be.
While we're at it, finally split the async mailbox completion handlers
into FC and parallel SCSI functions. This makes it much cleaner and
easier to figure out what is or isn't a legal async mailbox completion
code for different card classes.
PR: kern/144250
Submitted partially by: Charles D
MFC after: 1 week
numbers and handle types in rational way. This will better protect from
(unwittingly) dealing with stale handles/commands.
Fix the watchdog timeout code to better protect itself from mistakes.
If we run an abort on a putatively timed out command, the command
may in fact get completed, so check to make sure the command we're
timing it out is still around. If the abort succeeds, btw, the command
should get returned via a different path.
If the NAA is type 2, the Node WWN is the Port WWN with the 12 bits
of port (48..60) cleared. This iff a wwn fetched from NVRAM is zero.
MFC after: 1 week
Add a maximum response length for FCP RSPNS IUs.
Clarify some of the FC option words for setting parameters
and try and disable automatic PRLI when in target mode- this
should correct some cases of N-port topologies with 23XX cards
where we put out an illegal PRLI (in target mode only we're
not supposed to put out a PRLI).
we at least don't panic.
We don't really support dual role mode (INITIATOR/TARGET) any more. We
should but it's broken and will take a fair amount of effort to fix
and correctly manage both initiator and target roles sharing the port
database. So, for now, disallow it.
firmware loading bugs.
Target mode support has received some serious attention to make it
more usable and stable.
Some backward compatible additions to CAM have been made that make
target mode async events easier to deal with have also been put
into place.
Further refinement and better support for NP-IV (N-port Virtualization)
is now in place.
Code for release prior to RELENG_7 has been stripped away for code clarity.
Sponsored by: Copan Systems
Reviewed by: scottl, ken, jung-uk kim
Approved by: re
controllers. Reading this register, for which there are indications
that it doesn't really exist, returns 0 on at least some 12160
and doing so on Sun Fire V880 causes a data access error exception.
Reported and tested by: Beat Gaetzi
Approved by: mjacob
Obtained from: OpenBSD (modulo setting isp_lvdmode)
First, we were never correctly checking for a 24XX Status Type 0
response- that cased us to fall through to evaluate status for
commands as if this were a 2100/2200/2300 Status Type 0 response.
This is *close*, but not quite the same. This has been reported
to be apparent with some wierd lun configuration problems with
some arrays. It became glaringly apparent on sparc64 where none
of the correct byte swap things were done.
Fixing this omission then caused a whole universe shifting debug
cycle of endian issues for the 2400. The manual for 24XX f/w turns
out to be wrong about the endianness of a couple of entities. The
lun and cdb fields for the type 7 request are *not* unconditionally
big endian- they happen to be opposite of whatever the endian of
the current machine type is. Same with the sense data for the
24XX type 0 response.
While we're at it investigate and resolve some NVRAM endian
issues.
Approved by: re (ken)
MFC after: 3 days
request queues rather than shove it down a word at a time, we have
to remember to put it into little endian format. Use the macros
ISP_IOXPUT_{16,32} for this purpose. Otherwise, on sparc the firmware
is loaded garbled and we get a (not surprisingly) firmware checksum
failure and the card won't start and we don't attach it.
Approved by: re (bruce)
MFC after: 3 days
Seems to work on RELENG_4 through -current and also on sparc64
now. There may still be some issues with the auto attach/detach
code to sort out.
MFC after: 3 days
an ICB. This shows up on card restarts, and usually for
2200-2300 cards. What happens is that we start up,
attempting to acquire a hard address. We end up instead
being an F-port topology, which reports out a loop id
of 0xff (or 0xffff for 2K Login f/w). Then, if we restart,
we end up telling the card to go off an acquire this loop
address, which the card then rejects. Bah.
Compilation fixes from Solaris port.
front of isp_init so we can read NVRAM even if we're role ISP_NONE.
Prepare for reintroduction of channels (for FC) for N-Port
Virtualization.
Fix a botch in handle assignment that caused us to nuke one device
when a new one arrives and end up with two devices with the same
identity in the virtual target mapping table.
server.
Don't complain about a hard loop id of 0xffff- we get this in
point-to-point topologies with the 2300 and 2K Login firmware.
Up the timeout on register FC4 types commands.
with- not hope for the best. Change some things which were gated
off of 24XX to be gated off of 2K login support. Convert some
isp_prt calls to xpt_print calls.
and provied an isp_control entry point so that the outer layers can
do PLOGI/LOGO explicitly. Add MS IOCB support. This completes the cycle
for base support for SMI-S.
Only complain about FC Reponse errors if they're nonzero.
Shorten some PortID printouts for local loop.
Add an internal isp_xcmd_t data structure which we'll use for some
CT-Passthru support as part of adding SMI-S.
gone device timers and zombie state entries. There are tunables
that can be used to select a number of parameters.
loop_down_limit - how long to wait for loop to come back up before
declaring
all devices dead (default 300 seconds)
gone_device_time- how long to wait for a device that has appeared
to leave the loop or fabric to reappear (default 30 seconds)
Internal tunables include (which should be externalized):
quick_boot_time- how long to wait when booting for loop to come up
change_is_bad- whether or not to accept devices with the same
WWNN/WWPN that reappear at a different PortID as being the 'same'
device.
Keen students of some of the subtle issues here will ask how
one can keep devices from being re-accepted at all (the answer
is to set a gone_device_time to zero- that effectively would
be the same thing).
options field in register 10 will be deterministic, not random.
Correct the number of input bits for EXECUTE_FIRMWARE 0..1 to
0..2- the 2322 and 24XX cards use mailbox register 2 to specify
whether the f/w being executed is freshly loaded or not.
Correct the number of input bits for {READ,WRITE}_RAM_WORD_EXTENDED
so that register 8 gets picked up.
Fix the indexing and offset for the 2322 f/w download so that it
correctly puts the different code segments where they belong.
Move VERIFY_CHECKSUM to be the 'else' clause to 2322 f/w downloads-
the EXECUTE_FIRMWARE command for 2322 and 24XX cards will tell you
if the f/w checksum is incorrect and VERIFY_CHECKSUM only works for
RISC SRAM address < 64K so you can only do a VERIFY_CHECKSUM on the
first of the 3 f/w segments for the 2322.
Shorten the delay for the continuation mailbox commands- 1ms is
ridiculous (100us is more likely).
All of the more or less is really only for the 2322/6322 cards.
FreeBSD repository and to clean up the license header so as to
not pollute the license with file function.
Zero all mailbox structures prior to use (just in case). Change
the outgoing mailbox count for INIT_FIRMWARE to be correct.
Add MEMORY_BARRIER for the few scratch dma ops that were missing
them plus add a couple of hi 32 bit dma ops (we could probably
allow 64 bit scratch and request/response queue dma now).
(and by extension, the 2422).
One peculiar thing I've found with the 2322 is that if you
don't force it to do Hard LoopID acquisition, the firmware
crashes. This took a while to figure out.
While we're at it, fix various bugs having to do with NVRAM
reading and option setting with respect to pieces of NVRAM.
Pull in some target mode changes from a private branch.
Pull in some more RELENG_4 compilation changes.
A lot of lines changed, but not much content change yet.
to getting rid u_int for uint and so on).
b) Turn back on 64 bit DAC support. Cheeze it a bit in that we have two
DMA callback functions- one when we have bus_addr_t > 4 bits in width and
the other which should be normal. Even Cheezier in that we turn off setting
up DMA maps to be BUS_SPACE_MAXADDR if we're in ISP_TARGET_MODE. More work
on this in a week or so.
c) Tested under amd64 and 1MB DFLTPHYS, sparc64, i386 (PAE, but insufficient
memory to really test > 4GB). LINT check under amd64.
MFC after: 1 month
up to date. Principle changes for this reelase is to support 2K Port Login
firmware. This allows us to support the 2322 (and 2422 4Gb) cards which only
come with the 2K Port Login firmware. The 2322 should now work- but we don't
have firmware sets for it in ispfw (as the change to load 2K Port Login f/w
hasn't been made- that f/w is so big it has to be loaded in more than one
chunk).
Other changes are the beginnings of cleaning up some long standing target
mode issues. The next changes here will incorporate a lot of bug fixes
from others.
Finally, some copyright cleanup and attempts to make the parts of the
driver that are FreeBSD specific start conforming more to FreeBSD style.
MFC after: 1 month
Use the correct number of handles for multihandle returns.
Very, very, rarely on some SMP systems we've seen an 'unstable' type
in the response queue. I dunno whether or not it's a bug in our
handling, or whether there's a cache incoherency issue, but
try to guard against it.
MFC after: 2 weeks
