The current mapping of driver counters to netstat counters is wrong.
For example, a single jabber packet, will cause the Ierrs counter to
count three times.
The work for mapping the hardware and software counters to their right
place in netstat counters were already done in Linux, take that as is
to the FreeBSD driver.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
ib_req_notify_cq may return negative value which will indicate a
failure. In the case of uncorrectable error, we will end up in an
endless loop. Fix that, by going to another loop with poll_more
only if there is anything left to poll.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
To be used by the mlx5 callbacks exposed to the mlxfw module.
Linux commit:
d2ad488b0073bd1a2c3f5d2ea50a7eb632103e5d
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Enhance MCAM to allow the driver to query which access regs are
supported. For now, expose the regs needed for FW flashing.
Linux commit:
0ab87743cc8c5bcd482daf71961ed5fc45349e01
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
MCC (Management Component Control) allows to control a firmware
component update.
MCDA (Management Component Data Access) allows to read and write
a firmware component.
MCQI (Management Component Query Information) allows to query
information about firmware components.
Linux commit:
4717628938423fcba0aa8fa889e9fed4eb6a655f
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
On load_one, we now cache our capabilities registers internally, similar
to QUERY_HCA_CAP. Capabilities can later be queried using macros
introduced in this patch.
Linux commit:
71862561f3a62015a11de16d1c306481e8415c08
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Introduced registers will expose capabilities of new registers and
features related to port/management.
Driver will query MCAM and PCAM in order to avoid failing on old
firmwares with lack of support.
Linux commit:
c835ad64683bd3e2d1b31ed2cb1ff4366932edb1
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
PCAM: Ports capabilities mask register.
MCAM: Management capabilities mask register.
PCAM and MCAM registers will provide information regarding firmware
support for different features, in order to avoid cases where new driver
combined with old firmware results in syndromes (for ex. PCIe counters
before this patchset).
Linux commit:
cfdcbceaeffc669b70d904d80a2df9c86c232566
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Today mlx5 devices support two teardown modes:
1- Regular teardown
2- Force teardown
This change introduces the enhanced version of the "Force teardown" that
allows SW to perform teardown in a faster way without the need to reclaim
all the pages.
Fast teardown provides the following advantages:
1- Fix a FW race condition that could cause command timeout
2- Avoid moving to polling mode
3- Close the vport to prevent PCI ACK to be sent without been
scattered to memory
Linux commit:
fcd29ad17c6ff885dfae58f557e9323941e63ba2
MFC after: 3 days
Sponsored by: Mellanox Technologies
Else the SQs won't be properly released when closing rate-limited connections
leading to wrong state transitions on the SQ.
MFC after: 3 days
Sponsored by: Mellanox Technologies
When using CQE zipping, one can choose between RX hash and Checksum.
This will indicate the parameter on which a zipping session should be
stopped.
While porting the Linux code, Checksum was chosen. However, the value
of Checksum is not being used anywhere.
For the FreeBSD driver, we prefer to use the RX hash format which will
guarantee the RX hash value for all the mini CQEs.
While at it, make sure to initialize the Checksum value in the
decompressed CQE.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
After doing performance measurements, it seems like CQE zipping doesn't
have any significant benefit.
Moreover, we know that this feature is disabled by default on other
operating systems (Linux for example).
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Split the function into the mlx5e_update_stats_locked() core and make
mlx5e_update_stats_work() call the _locked helper, similar to many other
places in the kernel. This improves the code structure, making the
locking clean.
Submitted by: kib@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Instead of waiting for all jobs to be cancelled, simply close the completion
queue to prevent more completion events and let mlx5e_destroy_rq() cleanup
the remaining mbufs.
MFC after: 3 days
Sponsored by: Mellanox Technologies
The number of priorities is always 8, while the number of traffic classes
supported can vary. While at it convert the sysctl node into an array.
MFC after: 3 days
Sponsored by: Mellanox Technologies
Instead of reading Ethernet RFC 2819 pXtoYoctets counters from
hardware which counts RX octets, count tx_stat_pXtoYoctets from
Ethernet extended counters which counts TX octets.
TX jumbo counters should be accumulated only after the PPCNT
counters were fetched from hardware with their latest value.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Avoid an infinite software firmware reset loop that may be caused by a
hardware bug by limiting the maximum number of resets.
The counter between resets is reset by request for reset, and not by a
successful reset.
The interval between two resets can be configured via sysctl:
hw.mlx5.sw_reset_timeout
which is global to all mlx5 devices in the system.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Make sure the interrupt handlers don't race with the fast unload one
code in the shutdown handler.
MFC after: 3 days
Sponsored by: Mellanox Technologies
Temperature warning event is sent by FW to indicate high temperature
as detected by one of the sensors on the board.
Add handling of this event by writing the numbers of the alert sensors
to the kernel log.
Linux commit:
1865ea9adbfaf341c5cd5d8f7d384f19948b2fe9
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
While at it remove unused interface state bits. This also fixes and issue
during shutdown:
There is an issue where the firmware fails during mlx5_load_one,
the health_care timer detects the issue and schedules a health_care call.
Then the mlx5_load_one detects the issue, cleans up and quits. Then
the health_care starts and calls mlx5_unload_one to clean up the resources
that no longer exist and causes kernel panic.
The root cause is that the bit MLX5_INTERFACE_STATE_DOWN is not set
after mlx5_load_one fails. The solution is removing the bit
MLX5_INTERFACE_STATE_DOWN and quit mlx5_unload_one if the
bit MLX5_INTERFACE_STATE_UP is not set. The bit MLX5_INTERFACE_STATE_DOWN
is redundant and we can use MLX5_INTERFACE_STATE_UP instead.
Linux commit:
10a8d00707082955b177164d4b4e758ffcbd4017
b3cb5388499c5e219324bfe7da2e46cbad82bfcf
MFC after: 3 days
Sponsored by: Mellanox Technologies
Add support for DIM based on Linux,
with some minor adaptions specific to FreeBSD.
Linux commit
f97c3dc3c0e8d23a5c4357d182afeef4c67f5c33
MFC after: 3 days
Sponsored by: Mellanox Technologies
This is a prerequisite of unifying kernel zlib instances.
Submitted by: Yoshihiro Ota <ota at j.email.ne.jp>
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D20191
[ARM] Glue register copies to tail calls.
This generally follows what other targets do. I don't completely
understand why the special case for tail calls existed in the first
place; even when the code was committed in r105413, call lowering
didn't work in the way described in the comments.
Stack protector lowering breaks if the register copies are not glued
to a tail call: we have to insert the stack protector check before
the tail call, and we choose the location based on the assumption
that all physical register dependencies of a tail call are adjacent
to the tail call. (See FindSplitPointForStackProtector.) This is sort
of fragile, but I don't see any reason to break that assumption.
I'm guessing nobody has seen this before just because it's hard to
convince the scheduler to actually schedule the code in a way that
breaks; even without the glue, the only computation that could
actually be scheduled after the register copies is the computation of
the call address, and the scheduler usually prefers to schedule that
before the copies anyway.
Fixes https://bugs.llvm.org/show_bug.cgi?id=41417
Differential Revision: https://reviews.llvm.org/D60427
This should fix several instances of "Bad machine code: Using an
undefined physical register", when compiling ports such as
multimedia/vlc, audio/alsa-lib and devel/avro-c for armv6, with
-fstack-protector-strong.
Reported by: jbeich
PR: 237074, 237783, 237784
MFC after: 3 days
tun(4) and tap(4) share the same general management interface and have a lot
in common. Bugs exist in tap(4) that have been fixed in tun(4), and
vice-versa. Let's reduce the maintenance requirements by merging them
together and using flags to differentiate between the three interface types
(tun, tap, vmnet).
This fixes a couple of tap(4)/vmnet(4) issues right out of the gate:
- tap devices may no longer be destroyed while they're open [0]
- VIMAGE issues already addressed in tun by kp
[0] emaste had removed an easy-panic-button in r240938 due to devdrn
blocking. A naive glance over this leads me to believe that this isn't quite
complete -- destroy_devl will only block while executing d_* functions, but
doesn't block the device from being destroyed while a process has it open.
The latter is the intent of the condvar in tun, so this is "fixed" (for
certain definitions of the word -- it wasn't really broken in tap, it just
wasn't quite ideal).
ifconfig(8) also grew the ability to map an interface name to a kld, so
that `ifconfig {tun,tap}0` can continue to autoload the correct module, and
`ifconfig vmnet0 create` will now autoload the correct module. This is a
low overhead addition.
(MFC commentary)
This may get MFC'd if many bugs in tun(4)/tap(4) are discovered after this,
and how critical they are. Changes after this are likely easily MFC'd
without taking this merge, but the merge will be easier.
I have no plans to do this MFC as of now.
Reviewed by: bcr (manpages), tuexen (testing, syzkaller/packetdrill)
Input also from: melifaro
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D20044
The code never returned match comparing two datasets (not snapshots).
As result, uu_avl_find(), called from zfs_callback(), never succeeded,
allowing to add same dataset into the list multiple times, for example:
# zfs get name pers pers pers@z pers@z
NAME PROPERTY VALUE SOURCE
pers name pers -
pers name pers -
pers@z name pers@z -
With the patch:
# zfs get name pers pers pers@z pers@z
NAME PROPERTY VALUE SOURCE
pers name pers -
pers@z name pers@z -
MFC after: 1 week
Sponsored by: iXsystems, Inc.
(Introduced incorrectly in r347229 earlier today.)
As pointed out by kevans, 1.6 should be used for FreeBSD 13, like r340383.
Submitted by: kevans
Reported by: kib
Reviewed by: jilles
X-MFC-with: r347229
Differential Revision: https://reviews.freebsd.org/D20187
Checksum offloading for SCTP is not currently specified for virtio.
If the hypervisor announces checksum offloading support, it means TCP
and UDP checksum offload. If an SCTP packet is sent and the host announced
checksum offload support, the hypervisor inserts the IP checksum (16-bit)
at the correct offset, but this is not the right checksum, which is a CRC32c.
This results in all outgoing packets having the wrong checksum and therefore
breaking SCTP based communications.
This patch removes SCTP checksum offloading support from the virtio
network interface.
Thanks to Felix Weinrank for making me aware of the issue.
Reviewed by: bryanv@
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D20147
