base transfer speed to CAM. The actual value used (40MB/s) is fairly
arbitrary, but assumes the same 33% overhead as was implied by the
1MB/s figure we used for USB1 devices.
are not added to the list(s) of available settings. However, other drivers
can call the CPUFREQ_DRV_SETTINGS() method on those devices directly to
get info about available settings.
Update the acpi_perf(4) driver to use this flag in the presence of
"functional fixed hardware." Thus, future drivers like Powernow can
query acpi_perf for platform info but perform frequency transitions
themselves.
on dev.cpu.0 will affect all of the CPUs together. In the future,
independent control will be supported but this is good enough for now.
Check that the timecounter isn't TSC before switching (from Colin Percival.)
former is callable from user space and the latter from the kernel one. Make
kernel version take additional argument which tells if the respective call
should check for additional restrictions for sending signals to suid/sugid
applications or not.
Make all emulation layers using non-checked version, since signal numbers in
emulation layers can have different meaning that in native mode and such
protection can cause misbehaviour.
As a result remove LIBTHR from the signals allowed to be delivered to a
suid/sugid application.
Requested (sorta) by: rwatson
MFC after: 2 weeks
throttling, neglecting to do this kept the sysctls from appearing.
Attach an acpi_throttle device to each CPU that supports it.
Don't add a device if the P_BLK is invalid or if _PTC is not present.
This removes extraneous probe/attach failure messages on some machines.
Make the cpu throttle state local to the softc to account for partial
successes when changing the clock rate on MP machines.
for nodes hanging off of Central (untested), FireHose (untested) and
PCI (tested) busses.
- Add an additional parameter to OF_decode_addr() which specifies the
index of the register bank to decode.
These should allow to eventually add support for the Z8530 hanging off of
FireHose to uart(4) and to write support for PCI-based graphics adapters.
Suggested by: tmm (back in '03)
which will finally lead to kernel panic.
Security: This prevents a local (root-launched) DoS
Submitted by: Wojciech A. Koszek [dunstan at freebsd czest pl]
PR: 77421
MFC After: 1 week
o Add a fallback location for the MAC address. Most of the early ne2000
PC Cards were built from the same parts, so most of them have the same
address in the CIS to grab the MAC from. Use this address as our
fallback if we don't find anything better.
o Add printf, in bootverbose, noting the MAC addresses that we find along
the way.
# Better sanity checking of the MAC address is needed. Will have to
# investigate using/creating a centralized function to do this as a number
# of other PC Card drivers each have their own ad-hoc tests.
a definite setup was broken: two ng_ksockets are connected to each other,
connect()ed to different remote hosts, and bind()ed to different local
interfaces. In this case one ng_ksocket is fooled with tag from the other
one.
Put node id into tag. In rcvdata method utilize tag only if it has our
own id inside or id equals zero. The latter case is added to support
packets send by some third, not ng_ksocket node.
MFC after: 1 week
1. Dependency on netgraph module was broken (wrong version).
2. Netgraph node type was never destroyed on unload. This
was masked by problem #1.
Fixed both by using NETGRAPH_INIT(). Now netgraph node type
is created on module load, as in the rest of netgraph modules.
This information will be very useful for people who are tuning applications
which have a dependence on IPC mechanisms.
The following OIDs were documented:
Message queues:
kern.ipc.msgmax
kern.ipc.msgmni
kern.ipc.msgmnb
kern.ipc.msgtlq
kern.ipc.msgssz
kern.ipc.msgseg
Semaphores:
kern.ipc.semmap
kern.ipc.semmni
kern.ipc.semmns
kern.ipc.semmnu
kern.ipc.semmsl
kern.ipc.semopm
kern.ipc.semume
kern.ipc.semusz
kern.ipc.semvmx
kern.ipc.semaem
Shared memory:
kern.ipc.shmmax
kern.ipc.shmmin
kern.ipc.shmmni
kern.ipc.shmseg
kern.ipc.shmall
kern.ipc.shm_use_phys
kern.ipc.shm_allow_removed
kern.ipc.shmsegs
These new descriptions can be viewed using sysctl -d
PR: kern/65219
Submitted by: Dan Nelson <dnelson at allantgroup dot com> (modified)
No objections: developers@
Descriptions reviewed by: gnn
MFC after: 1 week
