returned and then infer the state from calls to _ON/_OFF. This works
around a problem in systems that don't correctly report the state (i.e.
the HP Omnibook 500 reports "on" for its fan always after it has been
turned on once).
I was unable to test this as the PAE kernel crashed with a "cannot copy
LDT" before coming up. When this gets a bit more testing, I'll fix the PAE
conf file to allow isp devices.
PR: 59728
to RS232 bridges, such as the one found in the DeLorme Earthmate USB GPS
receiver (which is the only device currently supported by this driver).
While other USB to serial drivers in the tree rely heavily on ucom, this
one is self-contained. The reason for that is that ucom assumes that
the bridge uses bulk pipes for I/O, while the Cypress parts actually
register as human interface devices and use HID reports for configuration
and I/O.
The driver is not entirely complete: there is no support yet for flow
control, and output doesn't seem to work, though I don't know if that is
because of a bug in the code, or simply because the Earthmate is a read-
only device.
This essentially merges revs 1.143-1.1445 of sys/pci/if_rl.c.
This now marks the interrupt MPSAFE along with making the mutex non-recursive.
Looked over by: bms
In places where we have long delays that doesn't depend on too accurate
timing, use ata_udelay() instead of DELAY() so we dont uselessly spin
the CPU if not nessesary;
It makes no sense in a PAE environment and is impossible to handle correctly.
This case is also never used right now. This should make the iir(4) driver
ready for PAE.
unless ACPI_DEBUG is defined. Users don't typically care about errant
breakpoint instructions. The HP Pavilion 7915 has this in its PCI0
_INI method for rev 0x6040000 of the RSDT.
Removed support for Intel 82541ER
Added fix for 82547 which corrects an issue with Jumbo frames larger than 10k.
Added fix for vlan tagged frames not being properly bridged.
Corrected TBI workaround.
Corrected incorrect LED operation issues
Submitted by: tackerman (Tony Ackerman)
MFC after: 2 weeks
should only affect current resources, it seems best to wait until all
configuration is done before disabling it. If this fixes any problems, it
is a MT5 candidate.
ENOENT when there's no PNP ID for this device node, or ENXIO when there
is one, but it doesn't match.
In the nonPNP case (as most Alpha systems appear to be), we were
treating the error return as an error, when it should be have ignored
it. Version 1.9 properly ignored it, but the attach re-write of 1.10
introduced this logic error.
Pointy Hat to: phk (for breaking it then asking me to fix it :-)
Sponsored by: The Voices in Bill Paul's Head, LLC
the old one is. Hence we need to evaluate the old one for _FDI since it
has a valid ACPI_HANDLE ivar. This is a minimal fix. Make a note that a
more complete one is to make fdc support the ACPI_HANDLE ivar for its
children.
This and the previous change are MT5 candidates.
nor are they 3D accelarators as the description would like us to
believe. Since the TGA2 adapter has a VGA mode (unlike the TGA adapter),
one can use the VGA driver instead.
This fixes GENERIC kernels on alpha with TGA2 adapters.
o Remove PSM_SYNCERR_THRESHOLD1. This value specified how many sync
errors were required before the mouse is re-initialised.
Re-initialisation is now done after (packetsize * 2) sync errors as
things aren't likely to improve after that.
o Reset lastinputerror when re-initialisation occurs. We don't want
to continue to drop data after re-initialisation.
o Count the number of failed packets independently of the syncerrors
statistic. syncerrors is useful for recovering sync within a single
packet. pkterrors allows us to detect when the mouse changes its
packet mode due to some external event (e.g. KVM switch).
o Reinitialize the mouse if we see more than psmpkterrthresh errors
during the validation period. The validation period begins as soon
as a sync error is detected and continues until psmerrsecs/msecs
time has elapsed. The defaults for these two values force a reset
if we see two packet errors in a 2 second period. This allows rapid
detection of packet framing errors caused by the mouse changing packet
modes.
o Export psmpkterrthresh as a sysctl
o Export psmloglevel as a sysctl.
o Enable more debugging code to be enabled at runtime via psmloglevel.
o Simplify verbose conditioned loging by using a VLOG macro.
o Add several comments describing the sync recovery algorithm of
this driver.
Large Portions by: Brian Somers <brian@Awfulhak.org>
Inspired and Frustrated by: Belkin KVMs
Reviewed by: njl, philip
its users.
netisr_queue() now returns (0) on success and ERRNO on failure. At the
moment ENXIO (netisr queue not functional) and ENOBUFS (netisr queue full)
are supported.
Previously it would return (1) on success but the return value of IF_HANDOFF()
was interpreted wrongly and (0) was actually returned on success. Due to this
schednetisr() was never called to kick the scheduling of the isr. However this
was masked by other normal packets coming through netisr_dispatch() causing the
dequeueing of waiting packets.
PR: kern/70988
Found by: MOROHOSHI Akihiko <moro@remus.dti.ne.jp>
MFC after: 3 days
Add missing untimeout that would get lost in handling of some
error situations, and caused what looked like random timeouts
afterwards when the timeout fired.
by default. As such, mark if_dc as IFF_NEEDSGIANT until such
time as appropriate locking review and testing can take place,
and the locking can be enabled by default.
RELENG_5 candidate.
