pmap_init(). Such a large preallocation is unnecessary and wastes
nearly eight megabytes of kernel virtual address space per gigabyte
of managed physical memory.
- Increase UMA_BOOT_PAGES by two. This enables the removal of
pmap_pv_allocf(). (Note: this function was only used during
initialization, specifically, after pmap_init() but before
pmap_init2(). During pmap_init2(), a new allocator is installed.)
such that 'ispcvt' can build. Unforunately 'ispcvt' is needed in order for
/etc/rc.d/syscons to run. This fixes the bug where I could not get my
keymap effective at boot.
as these ioctl's aren't MD. This also means they are installed in
/usr/include/dev/bktr now. Also provide compatability wrappers for
where these headers lived in 4.x.
Instead, allow the mapping to persist, but add the sf_buf to a free list.
If a later sendfile(2) or zero-copy send resends the same physical page,
perhaps with the same or different contents, then the mapping overhead is
avoided and the sf_buf is simply removed from the free list.
In other words, the i386 sf_buf implementation now behaves as a cache of
virtual-to-physical translations using an LRU replacement policy on
inactive sf_bufs. This is similar in concept to a part of
http://www.cs.princeton.edu/~yruan/debox/ patch, but much simpler in
implementation. Note: none of this is required on alpha, amd64, or ia64.
They now use their direct virtual-to-physical mapping to avoid any
emphemeral mapping overheads in their sf_buf implementations.
lots of old interfaces, and digi now supports all cards that dgb
supported. The author of the driver says that this is no longer
necessary.
Approved by: babkin@
or whose drivers haven't even compiled for years.
The loran hardware was very unique, and only a few copies of it ever
existed. It used the old COMPAT_ISA_DRIVER and when the author was
contacted, he indicated that he had no intention of ever updating this
driver and it was no longer relevant to the FreeBSD world and can be
removed without impact to anybody.
Approved by: phk
Update notes to reflect that cx is no longer a counted device
Update options for new cx option
# commented out ELAN_PPS and ELAN_XTAL since they produced errors
Submitted by: rik@cronyx.ru
Approved by: re@ <scottl>
- Add a really, really, nasty hack to provide stub versions of all of
the 'device apic' functions used by the ACPI MADT APIC enumerator if
'device apic' is not compiled into the kernel. This is gross but is
the best we can do with the current kernel linker implementation.
Approved by: re (scottl / blanket)
SI_SUB_CPU - 1 and probe enumerators, probe CPUs, and setup the local
APIC programming all at SI_SUB_CPU / SI_ORDER_FIRST. This is needed to
help get the ACPI module working again as it moves the APIC enumeration
code after SI_SUB_KLD.
- In the MADT parser, use mp_maxid rather than MAXCPU to terminate a loop
when assigning per-cpu ACPI IDs to avoid a dependency on 'options SMP'.
- Allow the apic device to be disabled via 'hint.apic.0.disabled' from the
loader. Note that since this is done in the local APIC code, it works
for both the ACPI and non-ACPI cases.
Approved by: re (scott / blanket)
1) mp_maxid is a valid FreeBSD CPU ID in the range 0 .. MAXCPU - 1.
2) For all active CPUs in the system, PCPU_GET(cpuid) <= mp_maxid.
Approved by: re (scottl)
Tested on: i386, amd64, alpha
This is the vastly updated cx drvier from Roman Kurakin <rik@cronyx.ru>
who has been patiently waiting for this update for sometime.
The driver is mostly a rewrite from the version we have in the tree.
While some similarities remain, losing the little history that the old
driver has is not a big loss, and the re@ felt it was easier this way (less
error prone).
The userland parts of this update will be committed shortly.
The driver is not connected to the build yet. I want to make sure I
don't break any platform at any time, so I want to test that with
these files in the tree before I continue (on the off chance I'm
forgetting a file).
I changed the DEBUG macro to CX_DEBUG from the code that was submitted
(to not break when we go to building with opt_global.h after the
release), as well adding $FreeBSD$.
Submitted by: Roman Kurakin
Approved by: re@ <scottl>
on. MCOUNT and FAKE_MCOUNT() may clobber all the call-used registers,
and one FAKE_MCOUNT() was placed so that an active %eax was clobbered.
The fix is to move this FAKE_MCOUNT() earlier where it should have
been anyway.
Fixed 3 layers of bitrot in the comment about why this FAKE_MCOUNT()
was where it was by removing the comment. (mcount() should be called
as early as possible after entering a new level, but an implementation
detail got in the way until 3 layers of changes ago.)
Kernel profiling still gives wrong results because the new interrupt
code rearranged object files too much. mcount() depends on trap,
syscall and interrupt handlers being between certain magic labels with
interrupt handlers last, and on nothing else being there. Splitting
up exception.o moved the magic labels to effectively random places
relative to what they are supposed to delimit. This mainly broke the
call graph; the flat profile is still usable.
code. Both the driver and the new code were wrong. Driver interrupt
handlers are supposed to take "void *vsc" arg, but some including all
COMPAT_ISA drivers and the pci part of the cy driver want an "int unit"
arg. They got this using bogus casts of function pointers which should
have kept working despite their bogusness. However, the new interrupt
code doesn't honor requests to pass an arg of ((void *)0), so things
are very broken if the arg is actually a representation of unit 0.
The fix is to use a normal "void *vsc" arg for the pci case and a
wrapper for the COMPAT_ISA case (of the cy driver). This cleans up
new-busification of the pci case but takes the COMPAT_ISA case a little
further from new-bus. The corresponding bug for the COMPAT_ISA case
has already been fixed similarly using a wrapper in compat_isa.c and
we need another wrapper just to undo that.
Fixed some directly related style bugs (mainly by removing compatibility
cruft).
cy.c:
Fixed an indirectly related old bug in cyattach_common(). A wrong status
was returned in the unlikely event that malloc() failed.
Approved by: re (scottl)
Make it possible to configure GPIO pins as led(4) devices, PPS inputs
and PPS-echo outputs with a sysctl. Led(4) and PPS-echo can be configured
for active-high or active-low.
Be more complete in initialization of timecounter hardware.
Approved by: re@
very early (SI_SUB_TUNABLES - 1) and is responsible for setting mp_maxid.
cpu_mp_probe() is now called at SI_SUB_CPU and determines if SMP is
actually present and sets mp_ncpus and all_cpus. Splitting these up
allows an architecture to probe CPUs later than SI_SUB_TUNABLES by just
setting mp_maxid to MAXCPU in cpu_mp_setmaxid(). This could allow the
CPU probing code to live in a module, for example, since modules
sysinit's in modules cannot be invoked prior to SI_SUB_KLD. This is
needed to re-enable the ACPI module on i386.
- For the alpha SMP probing code, use LOCATE_PCS() instead of duplicating
its contents in a few places. Also, add a smp_cpu_enabled() function
to avoid duplicating some code. There is room for further code
reduction later since much of this code is also present in cpu_mp_start().
- All archs besides i386 still set mp_maxid to the same values they set it
to before this change. i386 now sets mp_maxid to MAXCPU.
Tested on: alpha, amd64, i386, ia64, sparc64
Approved by: re (scottl)
source count pointers at them so that intr_execute_handlers() won't
choke when it tries to handle an unregisterd ATPIC interrupt source.
- Install the low-level ATPIC interrupt handlers when we first program the
ATPIC in atpic_startup() rather than at SI_SUB_INTR. This is only
necessary to work around buggy code that enables interrupts too early
in the boot process (namely, the vm86 code).
Approved by: re (rwatson)
more than one sf_buf for one vm_page. To accomplish this, we add
a global hash table mapping vm_pages to sf_bufs and a reference
count to each sf_buf. (This is similar to the patches for RELENG_4
at http://www.cs.princeton.edu/~yruan/debox/.)
For the uninitiated, an sf_buf is nothing more than a kernel virtual
address that is used for temporary virtual-to-physical mappings by
sendfile(2) and zero-copy sockets. As such, there is no reason for
one vm_page to have several sf_bufs mapping it. In fact, using more
than one sf_buf for a single vm_page increases the likelihood that
sendfile(2) blocks, hurting throughput.
(See http://www.cs.princeton.edu/~yruan/debox/.)
is the warning that points to the bug in `(char *)malloc(...)' where
malloc() is implicitly declared as returning int. We do similar things
here, but they work because u_int is the same as uintptr_t on i386's.)
- improve sysinfo(2) syscall;
- add dummy fadvise64(2) syscall;
- add dummy *xattr(2) family of syscalls;
- add protos for the syscalls 222-225, 238-249 and 253-267;
- add exit_group(2) syscall, which is currently just wired to exit(2).
Obtained from: OpenBSD
MFC after: 2 weeks
Its restoration in rev.1.102 was mistranslated to the equivalent of
setsofttty() in rev.1.105. This increased overheads by causing a
context switch to the SWI handler after almost every interrupt. The
increase was approx. 50% on a Celeron 366 (from 23 usec to 34 usec
per interrupt).
physical mapping.
- Move the sf_buf API to its own header file; make struct sf_buf's
definition machine dependent. In this commit, we remove an
unnecessary field from struct sf_buf on the alpha, amd64, and ia64.
Ultimately, we may eliminate struct sf_buf on those architecures
except as an opaque pointer that references a vm page.
longer uses these interrupt vectors for its ISA interrupt pins, so these
entries will not be overwritten. If we get a spurious interrupt from the
ATPIC when using the APIC, it will be treated as a stray interrupt instead
of causing a panic.
- Move the IPI and local APIC interrupt vectors up into the 0xf0 - 0xff
range. The pmap lazyfix IPI was reordered down next to the TLB
shootdowns to avoid conflicting with the spurious interrupt vector.
- Move the base of APIC interrupts up 16 so that the first 16 APIC
interrupts do not overlap the vectors used by the ATPIC.
- Remove bogus interrupt vector reservations for LINT[01].
- Now that 0xc0 - 0xef are available, use them for device interrupts.
This increases the number of APIC device interrupts to 191.
- Increase the system-wide number of global interrupts to 191 to catch up
to more APIC interrupts.
Requested by: peter (2)
vector stubs and into the C functions they call.
- Move disabling and EOIing of interrupt sources out of PIC driver entry
points and into intr_execute_handlers(). Intr_execute_handlers() only
disables a source for an interrupt if it is a stray interrupt or has
threaded handlers. Sources with fast handlers no longer disable (mask)
the source while executing the handlers.
- Move the setting of clkintr_pending into intr_execute_handlers() and set
the variable for any interrupt source with a vector of 0. (Should only
be true for IRQ 0.) This fixes clkintr_pending in the NO_MIXED_MODE
case.
- Implement lapic_eoi() and use it to implement ioapic_eoi_source().
- Rename atpic_sched_ithd() to atpic_handle_intr() since it is used to
handle all atpic interrupts and not just threaded ones.
Inspired by: peter's changes to amd64 in p4 (1)
Requested by: bde (2)
interrupt such as IRQ 22 or 19. However, the ACPI BIOS still routes
interrupts from some PCI devices to the same intpin calling the pin
IRQ 22. Thus, ACPI expects to address a single interrupt source via two
different names. To work around this, if the SCI is remapped to a non-ISA
interrupt (i.e., greater than 15), then we use
acpi_OverrideInterruptLevel() function to tell ACPI to use IRQ 22 or 19
rather than IRQ 9 for the SCI.
Previously we would change IRQ 22 or 19's name to IRQ 9 when we encountered
such an Interrupt Source Override entry in the MADT which routed the SCI
properly but left PCI devices mapped to IRQ 22 or 19 w/o a routable
interrupt.
Tested by: sos
should now only have HTT CPUs if they have explicitly asked for them
either by enabling HyperThreading in the BIOS or by using the
MPTABLE_FORCE_HTT kernel option.
should only be used if they are enabled in the BIOS. Now that we support
enumerating CPUs using the ACPI MADT, any HTT machine using ACPI should
respect the BIOS setting. For HTT machines with ACPI disabled in the
kernel, the MPTABLE_FORCE_HTT kernel option can be used to try to probe HTT
CPUs like have done in the past for the MP Table case. This option should
only be enabled if HTT is enabled in the BIOS.
Since all callers either passed 0 or 1 for clear_ret, define bit 0 in
the flags for use as clear_ret. Reserve bits 1, 2 and 3 for use by MI
code for possible (but unlikely) future use. The remaining bits are for
use by MD code.
This change is triggered by a need on ia64 to have another knob for
get_mcontext().
thread being waken up. The thread waken up can run at a priority as
high as after tsleep().
- Replace selwakeup()s with selwakeuppri()s and pass appropriate
priorities.
- Add cv_broadcastpri() which raises the priority of the broadcast
threads. Used by selwakeuppri() if collision occurs.
Not objected in: -arch, -current
pmap_pte() and pmap_pte_quick(). The distinction being based upon the
locks that are held by the caller. When the given pmap is not the
current pmap, pmap_pte() should be used when Giant is held and
pmap_pte_quick() should be used when the vm page queues lock is held.
- When assigning to PMAP1 or PMAP2, include PG_A anf PG_M.
- Reenable the inlining of pmap_is_current().
In collaboration with: tegge
pin that is used by the default identity mapping if it still maps to the
old vector. The ACPI case might need some tweaking for the SCI interrupt
case since ACPI likes to address the intpin using both the IRQ remapped to
it as well as the previous existing PCI IRQ mapped to it.
Reported by: kan
rather than signed. This fixes some cosmetics such as verbose printf's
for IRQs greater than 127.
- The calculation for next_ioapic_base was also adjusted so that it will
only complain once for each hole in the IRQs provided by ACPI for IO
APICs.
Reported by: Michal Mertl <mime@traveller.cz>
isa_device pointer as its argument and uses that to call the driver's
interrupt handler passing the unit number as its argument. This should
fix COMPAT_OLDISA devices with a unit number of 0.
Reviewed by: peter
Reported by: bde
- Compile 'device acpi' into GENERIC by default as well. Note that
the beastie loader menu item to disable ACPI still works if ACPI is
compiled into the kernel.
we would manage this better by having the interrupt code add each
interrupt vector to the resource map when each source is registered.
- Use the new interrupt code API for registering and tearing down interrupt
handlers.
- The MP code no longer knows anything specific about an MP Table.
Instead, the local APIC code adds CPUs via the cpu_add() function when
a local APIC is enumerated by an APIC enumerator.
- Don't divide the argument to mp_bootaddress() by 1024 just so that we
can turn around and mulitply it by 1024 again.
- We no longer panic if SMP is enabled but we are booted on a UP machine.
- init_secondary(), the asm code between init_secondary() and ap_init()
in mpboot.s and ap_init() have all been merged together in C into
init_secondary().
- We now use the cpuid feature bits to determine if we should enable
PSE, PGE, or VME on each AP.
- Due to the change in the implementation of critical sections, acquire
the SMP TLB mutex around a slightly larger chunk of code for TLB
shootdowns.
- Remove some of the debug code from the original SMP implementation
that is no longer used or no longer applies to the new APIC code.
- Use a temporary hack to disable the ACPI module until the SMP code has
been further reorganized to allow ACPI to work as a module again.
- Add a DDB command to dump the interesting contents of the IDT.
devices claiming resources that they don't actually use. The PIC drivers
only register valid interrupt sources, so we don't need to rely on these
drivers to claim invalid IRQs to prevent their use by other drivers.
slave pin on the master PIC in the !APIC_IO case. The PIC drivers now
manage these details internally.
- Remove an spl0() that hasn't done anything since SMPng was first
committed.
- Update some comments that have rotted since SMPng.
- Use intr_suspend/resume() callouts to the interrupt code layer which
suspends and resumes all the known interrupt sources instead of calling
icu_reinit() directly.
APIC Descriptor Table to enumerate both I/O APICs and local APICs. ACPI
does not embed PCI interrupt routing information in the MADT like the MP
Table does. Instead, ACPI stores the PCI interrupt routing information
in the _PRT object under each PCI bus device. The MADT table simply
provides hints about which interrupt vectors map to which I/O APICs. Thus
when using ACPI, the existing ACPI PCI bridge drivers are sufficient to
route PCI interrupts.
- The apic interrupt entry points have been rewritten so that each entry
point can serve 32 different vectors. When the entry is executed, it
uses one of the 32-bit ISR registers to determine which vector in its
assigned range was triggered. Thus, the apic code can support 159
different interrupt vectors with only 5 entry points.
- We now always to disable the local APIC to work around an errata in
certain PPros and then re-enable it again if we decide to use the APICs
to route interrupts.
- We no longer map IO APICs or local APICs using special page table
entries. Instead, we just use pmap_mapdev(). We also no longer
export the virtual address of the local APIC as a global symbol to
the rest of the system, but only in local_apic.c. To aid this, the
APIC ID of each CPU is exported as a per-CPU variable.
- Interrupt sources are provided for each intpin on each IO APIC.
Currently, each source is given a unique interrupt vector meaning that
PCI interrupts are not shared on most machines with an I/O APIC.
That mapping for interrupt sources to interrupt vectors is up to the
APIC enumerator driver however.
- We no longer probe to see if we need to use mixed mode to route IRQ 0,
instead we always use mixed mode to route IRQ 0 for now. This can be
disabled via the 'NO_MIXED_MODE' kernel option.
- The npx(4) driver now always probes to see if a built-in FPU is present
since this test can now be performed with the new APIC code. However,
an SMP kernel will panic if there is more than one CPU and a built-in
FPU is not found.
- PCI interrupts are now properly routed when using APICs to route
interrupts, so remove the hack to psuedo-route interrupts when the
intpin register was read.
- The apic.h header was moved to apicreg.h and a new apicvar.h header
that declares the APIs used by the new APIC code was added.
default we provide 16 interrupt sources for IRQs 0 through 15. However,
if the I/O APIC driver has already registered sources for any of those IRQs
then we will silently fail to register our own source for that IRQ.
Note that i386/isa/icu.h is now specific to the 8259A and no longer
contains any info relevant to APICs. Also note that fast interrupts no
longer use a separate entry point. Instead, both fast and threaded
interrupts share the same entry point which merely looks up the appropriate
source and passes control to intr_execute_handlers().
that provides methods via a PIC driver to do things like mask a source,
unmask a source, enable it when the first interrupt handler is added, etc.
The interrupt code provides a table of interrupt sources indexed by IRQ
numbers, or vectors. These vectors are what new-bus uses for its IRQ
resources and for bus_setup_intr()/bus_teardown_intr(). The interrupt
code then maps that vector a given interrupt source object. When an
interrupt comes in, the low-level interrupt code looks up the interrupt
source for the source that triggered the interrupt and hands it off to
this code to execute the appropriate handlers.
By having an interrupt source abstraction, this allows us to have different
types of interrupt source providers within the shared IRQ address space.
For example, IRQ 0 may map to pin 0 of the master 8259A PIC, IRQs 1
through 60 may map to pins on various I/O APICs, and IRQs 120 through
128 may map to MSI interrupts for various PCI devices.
Requested by: jhb
Initialize the real mode stack. This is needed at least for the return
address from the lcall.
Requested by: takawata
Fix style bugs in acpi_wakecode.S
Requested by: bde
Remove the kernel option now that we have the tunable.
to use the direct mapped KVA at KERNBASE to service the request. This also
allows pmap_mapdev() to be used for such addresses very early during the
boot process and might provide some small savings on KVA.
Reviewed by: peter
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
routines. Otherwise we run into trouble with speculative tlb preloads
on SMP systems. This effectively defeats Jeff's revision 1.438
optimization (for his pentium4-M laptop) in the SMP case. It breaks
other systems, particularly athlon-MP's.
