- create real_phys_avail which includes all memory ranges to be added to the direct map
- merge in nucleus memory to real_phys_avail
- distinguish between tag VA and index VA in tsb_set_tte_real for cases where page_size != index_page_size
- clean up direct map loop
of the bridge port and path cost have been administratively set or
calculated automatically by RSTP.
Make sure to transition from non-edge to edge when the port goes down
and the edge flag was manually set before.
This is needed to comply with the condition
((!portEnabled && AdminEdge) || ....)
in the Bridge Detection State Machine (IEE802.1D-2004, p. 171).
Reviewed by: thompsa
Approved by: bz (mentor)
pthread_cancel()ed, it is expected that the thread will not
consume a pthread_cond_signal(), therefor, we use thr_wake()
to mark a flag, the flag tells a thread calling do_cv_wait()
in umtx code to not block on a condition variable.
Thread library is expected that once a thread detected itself
is in pthread_cond_wait, it will call the thr_wake() for itself
in its SIGCANCEL handler.
- In hme_eint() print MIF register contents on MIF interrupts.
- In hme_mifinit() don't bother to preserve the previous MIF config.
This was mainly done in order to preserve the PHY select bit (external
or internal PHY) but which only needs to be set as appropriate when
reading from or writing to the desired PHY in hme_mii_{read,write}reg().
Similarly don't bother to set the PHY select bit in hme_mii_statchg().
- In hme_mii_{read,write}reg() ignore requests to PHYs other than the
external and internal PHY one.
- Move enabling/disabling the MII drivers of the external transceiver
from hme_init_locked() and based on the sheer presence of an external
to hme_mifinit() and based on the currently selected media, defaulting
to the internal transceiver when the media hasn't been set, yet.
Invoke hme_mifinit() from the newly added hme_mediachange_locked() so
the setting of the MII drivers is updated when changing media.
These changes keep the MII bus from wedging (which manifests in the HME
and the PHYs no longer being able to communicate with each other) when
the PHY device drivers isolate the unused PHY in two-PHY configurations
as present in f.e. Netra t1 100 while changing media, either from
hme_init_locked() (see also below) or via ifconfig(8). They also allow
for using both transceivers/PHYs.
- In the newly added hme_mediachange_locked() also reset the PHYs in two-
PHY configurations before invoking mii_mediachg(). This is required
for successfully unisolating the previously unused PHY when switching
between PHYs.
- Now that changing media should no longer cause problems back out rev.
1.27 and re-enable setting the current media in hme_init_locked() (see
the commit message of rev. 1.23 for more info).
These changes are roughly a merge of NetBSD gem.c rev. 1.32 - 1.35 (1.30
was already fixed differently in our 1.36; 1.31 and 1.32 were wrong) with
some parts reworked and things that don't make sense like setting the MII
drivers and restoring the previous MIF and XIF settings in hme_mii_{read,
write}reg() omitted.
MFC after: 2 weeks
- add better checks on non-existing directories to prevent error
messages at run time;
- introduce a function log() to help debugging diskless booting
when things don't work;
- modify the parsing of diskless_remount so you can add mount_nfs
options after the pathname. You could use 'remount' to do something
similar, but this way is more convenient because you don't have to
hardwire the server name in the command.
- document the above.
I have been running the above in a diskless lab since february on RELENG_6.
MFC after: 1 week
Use TAILQ_FOREACH_SAFE instead of the unsafe one where an item is removed
from the queue.
This prevents a panic on kldunload.
Submitted by: rdivacky
Tested by: bsam
set birthtime to FAT CTime (creation time) and in the other cases
set birthtime to -1.
o Set ctime to mtime instead of FAT CTime which has completely
different meaning.
PR: kern/106018
Submitted by: Oliver Fromme
MFC after: 1 month
Obtained from: OpenBSD
Note: In the case of a full buffer the OpenBSD implementation will
leave in the format string an invalid escape sequence. This appears
to be harmless with our C library, but according to C99 this can
cause undefined behavior.
MFC after: 2 weeks
Note: It would be nice to be able to implement getformat() using
fmtcheck(3), but fmtcheck does not distinguish between signed and
unsigned types, a facility jot needs to perform range checks on its
output.
Submitted by: Per Kristian Hove
MFC after: 2 weeks
read wasn't flagging the SYNC mode was enabled. The temp
values for offset and sync period were uint8_t, but were
being assigned and shifted from a uint32_t value.
This didn't show up in testing because a random number
of 1030 cards set a bit that says "honor BIOS negotiation",
which means this whole code path was skipped.
This should clear up at least some of the negotation
issues that have been seen.
author can't remember why it was there.
The CTS_SCSI_FLAGS_TAG_ENB remains in place, and makes sense, and is
checked all over the place.
The CTS_SPI_FLAGS_TAG_ENB was probably an attempt to distinguish
protocol and transport tag capabilities. At the very least this can
be confusing and prone to many bugs, so let's just assume that the
transport tag case just flows from the protocol (and vice versa)
for now.
and by only delaying when an RTC register is written to. The delay
after writing to the data register is now not just a workaround.
This reduces the number of ISA accesses in the usual case from 4 to
1. The usual case is 2 rtcin()'s for each RTC interrupt. The index
register is almost always RTC_INTR for this. The 3 extra ISA accesses
were 1 for writing the index and 2 for delays. Some delays are needed
in theory, but in practice they now just slow down slow accesses some
more since almost eveyone including us does them wrong so modern systems
enforce sufficient delays in hardware. I used to have the delays ifdefed
out, but with the index register optimization the delays are rarely
executed so the old magic ones can be kept or even implemented non-
magically without significant cost.
Optimizing RTC interrupt handling is more interesting than it used to
be because RTC interrupts are currently needed to fix the more efficient
apic timer interrupts on some systems. apic_timer_hz is normally 2000
so the RTC interrupt rate needs to be 2048 to keep the apic timer
firing on such systems. Without these changes, each RTC interrupt
normally took 10 ISA accesses (2 PIC accesses and 2 sets of 4 RTC
accesses). Each ISA access takes 1-1.5uS so 10 of then at 2048 Hz
takes 2-3% of a CPU. Now 4 of them take 0.8-1.2% of a CPU.
priority mutex implemented, it is the time to introduce this stuff,
now we can use umutex and ucond together to implement pthread's
condition wait/signal.
Fix things to use the LSI-Logic Fusion Library mask and shift names for
offset and sync, no matter how awkward they are, in preference to just
plain numbers.
- Don't set MIIF_NOISOLATE so amphy(4) can be used in configurations
with multiple PHYs. There doesn't seem to be a problem with isolating
AM79c873 and workalikes per se nor in combination with the NICs they're
used with and amphy(4) was already adding IFM_NONE anyway.
- Use mii_phy_add_media() instead of mii_add_media() so the latter can
be eventually retired.
- Take advantage of mii_phy_setmedia().
- Fix a whitespace nit.
Obtained from: NetBSD dmphy(4) (except for the last item)
MFC after: 2 weeks
the currently selected media is of type IFM_AUTO as auto-negotiation
doesn't need to be kicked anyway.
- Fix a whitespace nit.
- Probe another Altima PHY, which is a AC101 workalike and integrated
in at least ADMtek ADM8511 but apparently is not mentioned in any
publically available data sheet so the actual identifier is unknown.
- Don't set MIIF_NOISOLATE so acphy(4) can be used in configurations
with multiple PHYs. There doesn't seem to be a problem with isolating
AC101 and workalikes per se nor in combination with the NICs they're
used with.
- Use mii_phy_add_media() instead of mii_add_media() so the latter can
be eventually retired.
- Take advantage of mii_phy_setmedia().
Obtained from: NetBSD (except for the first and second item)
MFC after: 2 weeks
in at least ADMtek ADM8511 but apparently is not mentioned in any
publically available data sheet so the actual identifier is unknown.
- Add Davicom DM9102 PHY.
- Add DM9101 to the description of AMD 79C873 as at least some Davicom
DM9101F identify identical to AMD 79C873.
Obtained from: NetBSD
MFC after: 2 weeks
with multiple PHYs. There doesn't seem to be a problem with isolating
78Q2120 per se nor in combination with the NICs they're used with and
tdkphy(4) was already adding IFM_NONE anyway.
- Set MIIF_NOLOOP as loopback doesn't work with this PHY. The MIIF_NOLOOP
flag currently triggers nothing but hopefully will be respected by
mii_phy_setmedia() later on.
- Use mii_phy_add_media() instead of mii_add_media() so the latter can
be eventually retired.
- Take advantage of mii_phy_setmedia().
Thanks to Hans-Joerg Sirtl for lending me test hardware.
Obtained from: NetBSD tqphy(4)
MFC after: 2 weeks
with multiple PHYs and un-comment case IFM_NONE in case MII_MEDIACHG
rgephy_service(). There doesn't seem to be a problem with isolating
RTL8169S and their internal PHY.
- Take advantage of mii_phy_add_media(). [1]
Obtained from: NetBSD [1]
Tested by: yongari
MFC after: 2 weeks
- Fix some whitespace nits.
- Fix some spelling in comments.
- Use MII_ANEGTICKS instead of 5.
- Don't define variables in nested scope.
- Remove superfluous returns at the end of void functions.
- Remove unused static global rgephy_mii_model.
- Remove dupe $Id$ in tdkphy(4).
- Sort brgphys table.
MFC after: 2 weeks
and Daichi GOTO <daichi@FreeBSD.org> for submitting this
major rewrite of unionfs. This rewrite was done to
try to solve many of the longstanding crashing and locking
issues in the existing unionfs implementation. This
implementation also adds a 'MASQUERADE mode', which allows
the user to set different user, group, and file permission
modes in the upper layer.
Submitted by: daichi, Masanori OZAWA
Reviewed by: rodrigc (modified for minor style issues)
- Playback and headphone/speaker automute works.
- Recording untested due to me being deaf doing back-and-forth
remote debugging.
Free Macbook donation is highly appreciated :)
Tested by: Dennis Pielken <mips128@gmx.net>
mii_phy_match() API and takes care of the PHY device probe based on
the struct mii_phydesc array and the match return value provided.
Convert PHY drivers to take advantage of mii_phy_dev_probe(),
converting drivers to provide a mii_phydesc table in the first
place where necessary.
Reviewed by: yongari
MFC after: 2 weeks
- Currently LINUX_MAX_COMM_LEN is smaller than MAXCOMLEN, but in case
this will change we have a buffer overflow. Apply some defensive
programming to DTRT when this should happen.
- Use copyinstr() instead of copyin where appropriate.
* Fallback to copyin() in case of ENAMETOOLONG. [1]
* Use the right source and destination (it was wrong before).
- Use strlcpy instead of strcpy.
- Properly lock the read case (PR_GET_NAME) like the write case.
Reviewed by: rwatson (except [1])
Suggested by: rwatson [1]
