re-add $ipv6_enable support for backward compatibility. From
UPDATING:
1. To use IPv6, simply define $ifconfig_IF_ipv6 like $ifconfig_IF
for IPv4. For aliases, $ifconfig_IF_aliasN should be used.
Note that both variables need the "inet6" keyword at the head.
Do not set $ipv6_network_interfaces manually if you do not
understand what you are doing. It is not needed in most cases.
$ipv6_ifconfig_IF and $ipv6_ifconfig_IF_aliasN still work, but
they are obsolete.
2. $ipv6_enable is obsolete. Use $ipv6_prefer and/or
"inet6 accept_rtadv" keyword in ifconfig(8) instead.
If you define $ipv6_enable=YES, it means $ipv6_prefer=YES and
all configured interfaces have "inet6 accept_rtadv" in the
$ifconfig_IF_ipv6. These are for backward compatibility.
3. A new variable $ipv6_prefer has been added. If NO, IPv6
functionality of interfaces with no corresponding
$ifconfig_IF_ipv6 is disabled by using "inet6 ifdisabled" flag,
and the default address selection policy of ip6addrctl(8)
is the IPv4-preferred one (see rc.d/ip6addrctl for more details).
Note that if you want to configure IPv6 functionality on the
disabled interfaces after boot, first you need to clear the flag by
using ifconfig(8) like:
ifconfig em0 inet6 -ifdisabled
If YES, the default address selection policy is set as
IPv6-preferred.
The default value of $ipv6_prefer is NO.
4. If your system need to receive Router Advertisement messages,
define "inet6 accept_rtadv" in $ifconfig_IF_ipv6. The rc(8)
scripts automatically invoke rtsol(8) when the interface becomes
UP. The Router Advertisement messages are used for SLAAC
(State-Less Address AutoConfiguration).
This completes the fix from r185586.
PR: kern/139059
Reported by: Daniel Braniss <danny@cs.huji.ac.il>
Submitted by: Jaakko Heinonen <jh@saunalahti.fi>
Tested by: Daniel Braniss <danny@cs.huji.ac.il>
MFC after: 3 days
a large page size that is greater than malloc(3)'s default chunk size but
less than or equal to 4 MB, then increase the chunk size to match the large
page size.
Most often, using a chunk size that is less than the large page size is not
a problem. However, consider a long-running application that allocates and
frees significant amounts of memory. In particular, it frees enough memory
at times that some of that memory is munmap()ed. Up until the first
munmap(), a 1MB chunk size is just fine; it's not a problem for the virtual
memory system. Two adjacent 1MB chunks that are aligned on a 2MB boundary
will be promoted automatically to a superpage even though they were
allocated at different times. The trouble begins with the munmap(),
releasing a 1MB chunk will trigger the demotion of the containing superpage,
leaving behind a half-used 2MB reservation. Now comes the real problem.
Unfortunately, when the application needs to allocate more memory, and it
recycles the previously munmap()ed address range, the implementation of
mmap() won't be able to reuse the reservation. Basically, the coalescing
rules in the virtual memory system don't allow this new range to combine
with its neighbor. The effect being that superpage promotion will not
reoccur for this range of addresses until both 1MB chunks are freed at some
point in the future.
Reviewed by: jasone
MFC after: 3 weeks
It is quite inconvenient that if an application for xterm uses 256 color
mode, text suddenly starts to blink (because of ;5; in the middle).
We'd better just implement 256 color mode and add a conversion routine
from 256 to 8 color mode, which doesn't seem to be too bad in practice.
Remapping colors is done quite simple. If one of the channels is most
actively represented, primary colors are used. If two channels are most
actively represented, secondary colors are used. If all three channels
are equal (gray), it picks between black and white.
Reported by: Paul B. Mahol <onemda gmail com>
In some cases events may occur that move the cursor outside the
scrolling region while in origin mode, which is normally not possible.
Events like these include:
- Alignment test.
- Restore cursor.
Properly switch off origin mode in these cases.
MFC after: 1 month
devices that we also support, just not by default (thus only LINT or
module builds by default).
While currently there is only "/dev/full" [2], we are planning to see more
in the future. We may decide to change the module/dependency logic in the
future should the list grow too long.
This is not part of linux.ko as also non-linux binaries like kFreeBSD
userland or ports can make use of this as well.
Suggested by: rwatson [1] (name)
Submitted by: ed [2]
Discussed with: markm, ed, rwatson, kib (weeks ago)
Reviewed by: rwatson, brueffer (prev. version)
PR: kern/68961
MFC after: 6 weeks
unmount. In that case we cannot depend on the proper order of invalidating
vnodes, so we have to free resources when we have a chance.
PR: kern/139062
Reported by: trasz
MFC after: 3 days
well with forced unmounts when GFS vnodes are referenced.
- Make other preparations to GFS for forced unmounts.
PR: kern/139062
Reported by: trasz
MFC after: 3 days
- Clear all registers before calling real mode interrupt handlers as we did
for dpms and vesa and re-enable the function as it should be fixed by this.
- Tidy up register access. For example, when we call INT 0x15, AH=0xc0,
we used to initialize AX=0xc000 to clear AL at the same time but it is
very confusing. We don't have to do this any more because we are explicitly
clearing all registers now.
- Check size of system configuration table although it is almost always 8.
This is to make sure we are not reading some random low physical memory.
Hopefully it is just zero in that case. :-)
- Fix some style nits and add more comments.
Submitted by: paradox (ddkprog yahoo com)[1]
memory to support them. Some adapters have expansible memory slots but
video mode table is static. In this case, unusable modes may be reported.
Submitted by: paradox (ddkprog yahoo com) (initial patch)
- Remove CS and IP registers from x86bios.h. They have no use for us.
- Adjust register dump to make it little bit more useful for debugging.
Submitted by: paradox (ddkprog yahoo com)[1] (initial version)
Just run this to switch to xterm:
printf '\e[=T'
If you get bored and want to switch back to cons25, run this:
printf '\e[=1T'
I can now send an email to the lists, asking whether people are
interested in trying the xterm emulator.
I noticed a small inconsistency in delete and insert line between xterm
and libteken. libteken allows these actions to happen while the cursor
is placed outside the scrolling region, while xterm does not.
This behaviour seems to be VT100-like. Confirmation:
http://www.vt100.net/docs/vt102-ug/chapter5.html
"This sequence is ignored when cursor is outside scrolling region."
MFC after: 1 month
check if there are readers blocked by us via URWLOCK_WRITE_WAITERS flag,
and resume the readers. The error must be EAGAIN, otherwise there must
have memory problem, and nobody can rescue the buggy application.
The revision 197445 might be reverted.
