offload for VLAN frames are also supported. The VLAN hardware
assistance is available only on 82550/82551 based controllers.
While I'm here change the confusing name of bit1 in byte 22 of
configuration block to vlan_drop_en. The bit controls whether
hardware strips VLAN tagged frame or not. Special thanks to wpaul
who sent valuable VLAN related information to me.
Tested on: i386, sparc64
events. Just reading PMDR register was not enough to have fxp(4)
immuninize against received magic packets during system boot.
Tested by: Alexey Shuvaev < shuvaev <> physik DOT uni-wuerzburg DOT de >
module; the ath module now brings in the hal support. Kernel
config files are almost backwards compatible; supplying
device ath_hal
gives you the same chip support that the binary hal did but you
must also include
options AH_SUPPORT_AR5416
to enable the extended format descriptors used by 11n parts.
It is now possible to control the chip support included in a
build by specifying exactly which chips are to be supported
in the config file; consult ath_hal(4) for information.
o eliminate private state indexed by 802.11 rate codes; use the hal's
rate tables directly to get the same info
o calculate a mask of operational rates to optimize lookups and checks
(instead of using for loops and similar)
o optimize size bin operations
o ignore rates marked as "do not use" in the hal phy tables
o fix bug that caused upshifting to break in 11g once the rate dropped
below 11Mb/s
o add more intelligent multi-rate tx schedules
o add support for 1/2 and 1/4 width channels
o add dev.ath.X.sample_stats sysctl to dump runtime statistics to the console
(needs to go up to a user app)
o export more tuning knobs via sysctls (still a couple of magic constants)
necessary workarounds, add code to detect these hangs and distinguish
them from other events; note this code is only invoked for anomalous
conditions and (at the moment) is a noop because the hang detection
code is in a new hal that's coming shortly
and Core Duo), models 0xF (Core2), model 0x17 (Core2Extreme) and
model 0x1C (Atom).
In these CPUs, the actual numbers, kinds and widths of PMCs present
need to queried at run time. Support for specific "architectural"
events also needs to be queried at run time.
Model 0xE CPUs support programmable PMCs, subsequent CPUs
additionally support "fixed-function" counters.
- Use event names that are close to vendor documentation, taking in
account that:
- events with identical semantics on two or more CPUs in this family
can have differing names in vendor documentation,
- identical vendor event names may map to differing events across
CPUs,
- each type of CPU supports a different subset of measurable
events.
Fixed-function and programmable counters both use the same vendor
names for events. The use of a class name prefix ("iaf-" or
"iap-" respectively) permits these to be distinguished.
- In libpmc, refactor pmc_name_of_event() into a public interface
and an internal helper function, for use by log handling code.
- Minor code tweaks: staticize a global, freshen a few comments.
Tested by: gnn
controllers. ICH based controllers are treated as 82559. 82557,
earlier revision of 82558 and 82559ER have no WOL capability.
o WOL support requires help of a firmware so add check whether
hardware is capable of handling magic frames by reading EEPROM.
o Enable accepting WOL frames only when hardware is about to
suspend or shutdown. Previously fxp(4) used to allow receipt of
magic frame under normal operation mode which could cause
hardware hang if magic frame is received by hardware. Datasheet
clearly states driver should not allow WOL frames under normal
operation mode.
o Disable WOL frame reception in device attach so have fxp(4)
immunize against system hang which can be triggered by magic
packets when the hardware is not in fully initialized state.
o Don't reset all hardware configuration data in fxp_stop()
otherwise important configuration data is lost and this would
reset WOL configuration to default state which in turn cause
hardware hang on receipt of magic frames. To fix the issue,
preserve hardware configuration data by issuing a selective
reset.
o Explicitly disable interrupts after issuing selective reset as
reset may unmask interrupts.
Tested by: Alexey Shuvaev < shuvaev <> physik DOT uni-wuerzburg DOT de >
will sometimes fail to initialize problem due to a lock
contention with management hardware. However, in order to
deliver that fix it was necessary to take a shared code
update as a whole, and this required scattered changes in
the core code to be compatible.
The em driver now has VLAN HW support added as the igb
driver had previously.
MFC after: ASAP - in time for 7.1 RELEASE
-This version has header split, and as a result a number of
aspects of the code have been improved/simplified.
- Interrupt handling refined for performance
- Many small bugs fixed along the way
MFC after: ASAP - in time for 7.1
- Bugfix: Don't excede static number of ports allowed when iterating
over endpoints within an interface.
- u3g_speeds contains speeds in baud, not bytes per second, so divide
the buffer size by 10.
o Configure controller to use dynamic TBD as TSO requires that
operation mode.
o Add a dummy TBD to tx_cb_u as TSO can access one more TBD in TSO
operation.
o Increase a DMA segment size to 4096 to hold a full IP segment
with link layer header.
o Unlike other TSO capable controllers, 82550/82551 does not
modify the first IP packet in TSO operation so driver should
create an IP packet with proper header. Subsequent IP packets
are generated from the header information in the first IP packet
header. Likewise pseudo checksum also should be computed by
driver for the first packet.
o TSO requires one more TBD to hold total TCP payload. To make
code simple for TSO/non-TSO case, increase the index of the
first available TBD array.
o Remove KASSERT that checks the size of a DMA segment should be
less than or equal to MCLBYTES as it's no longer valid in TSO.
o Tx threshold and number of TBDs field is used to store MSS in
TSO. So don't set the Tx threshold in TSO case.
82559 or later controllers added simple checksum calculation logic
in RU. For backward compatibility the computed checksum is appended
at the end of the data posted to Rx buffer. This type of simple
checksum calculation support had been used on several vendors such
as Sun HME/GEM, SysKonnect GENESIS and Marvell Yukon controllers.
Because this type of checksum offload support requires parsing of
received frame and pseudo checksum calculation with software
routine it still consumes more CPU cycles than that of full-fledged
checksum offload controller. But it's still better than software
checksum calculation.
Rx buffer and loads DMA map. Also add a function
fxp_discard_rfabuf that handles reusing Rx buffer/DMA map. With
this change fxp_add_rfabuf just handles appending a new RFA to
existing chain.
o Initialize mbuf length in fxp_new_rfabuf.
o Don't reset rnr and have fxp(4) handle received frames even if
it couldn't allocate new Rx buffer. This will make fxp(4) reload
updated RFA under rnr case. The rnr would still be reset to 0 if
polling is active and fxp(4) processed number of allowed Rx
events.
o Update if_iqdrops if fxp(4) couldn't allocate Rx buffer.
Previously fxp(4) used to try to reuse Rx buffer when new buffer
allocation is failed. But fxp(4) didn't take into account loaded
DMA map such that the same DMA map was loaded again without
unloading the map. There is no reason to unload the loaded map and
reload the same map again, just reusing the map is enough. I
believe the spare DMA map in softc was introduced to implement this
behaviour. Also fxp(4) used to stop Rx processing if once Rx buffer
allocation or DMA map load fails which in turn resulted in losing
incoming frames under heavy network load. With this change fxp(4)
should survive from resource shortage condition.
Fix some issues about re-scanning of the devices.
src/lib/libusb20/libusb20_ugen20.c
Fix issue about libusb20 having to release the
USB transfers before doing a SET_CONFIG, else
the kernel will kill the file handle.
src/sys/dev/usb2/core/usb2_device.
src/sys/dev/usb2/core/usb2_generic.c
src/sys/dev/usb2/core/usb2_generic.h
Add support for U3G devices.
Improve and cleanup FIFO free handling.
Improve device re-enumeration.
src/sys/dev/usb2/core/usb2_msctest.c
src/sys/dev/usb2/core/usb2_msctest.h
Fix some problems in the USB Mass Storage Test.
Add Huawei vendor specific quirks.
src/sys/dev/usb2/core/usb2_request.c
Improve device re-enumeration.
src/sys/dev/usb2/ethernet/if_aue2.c
src/sys/dev/usb2/include/usb2_devid.h
src/sys/dev/usb2/include/usb2_devtable.h
src/sys/dev/usb2/quirk/usb2_quirk.c
Integrate changes from the old USB driver.
src/sys/dev/usb2/include/usb2_standard.h
Add definition of USB3.0 structures from USB.org.
src/sys/dev/usb2/serial/u3g2.c
src/sys/dev/usb2/serial/ugensa2.c
src/sys/modules/usb2/Makefile
src/sys/modules/usb2/serial_3g/Makefile
Import U3G driver.
Submitted by: Hans Petter Selasky (usb4bsd)
many bugs fixes, many more performance improvements.
Submitted by: Danny Braniss
M sbin/iscontrol/iscsi.conf.5
M sbin/iscontrol/iscontrol.8
M sbin/iscontrol/iscontrol.h
M sbin/iscontrol/config.c
M sbin/iscontrol/fsm.c
M sbin/iscontrol/login.c
M sbin/iscontrol/pdu.c
M sbin/iscontrol/misc.c
M sbin/iscontrol/auth_subr.c
M sbin/iscontrol/iscontrol.c
M sys/dev/iscsi/initiator/isc_cam.c
M sys/dev/iscsi/initiator/iscsi.h
M sys/dev/iscsi/initiator/isc_soc.c
M sys/dev/iscsi/initiator/iscsi_subr.c
M sys/dev/iscsi/initiator/iscsivar.h
M sys/dev/iscsi/initiator/isc_subr.c
M sys/dev/iscsi/initiator/iscsi.c
M sys/dev/iscsi/initiator/isc_sm.c
IFF_DRV_OACTIVE to note resource shortage to upper stack.
- Don't count number of mbuf chains. Default 32 DMA segments for a
frame is enough for most cases. If bus_dmamap_mbuf_sg fails use
m_collapse(9) to collapse the mbuf chain instead of relying on
expensive m_defrag(9).
- Move bpf handling to fxp_start_body() which is supposed to be
more appropriate place.
- Always arm watchdog timer whenever a new Tx request is made.
Previously fxp(4) used to arm watchdog timer only when
FXP_CXINT_THRESH-th Tx request is made. Because fxp(4) does not
rely on Tx interrupt to reclaim transmitted mbufs it's better to
arm watchdog timer to detect potential lockups.
- Add more aggresive Tx buffer reclaiming in fxp_start_body to make
room for new Tx requests. Since fxp(4) does not request Tx
completion interrupt for every frames it's necessary to clean
TXCBs in advance to saturate link.
- Make fxp(4) try to start more packets transmitting regardless of
interrupt type in fxp_intr_body.
patch the RX/TX performance becomes about 17~18 Mbps comparing with
the previous whose values were RX 7~8Mbps and TX 13~14Mbps.
- improve AL2230 RF handling in zd1211b
- support AL2230S RF that PV2000 is renamed to AL2230S
- use register ZYD_CR244, ZYD_CR243, ZYD_CR242 when the driver writes
values on RF. This routine is more faster than the original one
- use private TX lock to avoid LOR at zyd_raw_xmit()
- increase TX slots from 1 to 5
- needs to set the channel at IEEE80211_S_AUTH not IEEE80211_S_RUN
- detailed error handling. In previous the next command was sent to the
device even if there was errors
- setting ZYD_MAC_RX_THRESHOLD value should be different between 1211
and 1211b
- only try to stop the device at zyd_init_locked() if the device is
UPed
- do not use MTX_RECURSE
- do not try to grap Giant lock when the channel is changing
- move the device initialization routines from zyd_attach to zyd_init to
give a device full-reset chance to the driver.
- code cleanup at zyd_raw_xmit()
- simplify zyd_attach() routines
- resort functions and clean up variables
- DPRINTF style change.
- style(9)
Reviewed by: sam
check to fxp_txeof(). While I'm here unarm watchdog timer only if
there are no pending queued Tx requests.
Previously the watchdog timer was unarmed whenever Tx interrupt is
raised. This could be resulted in hiding root cause of watchdog
timeouts.
checksum offload configuration. Now checksum offload can be
controlled by ifconfig(8).
While I'm here add an additional check for interface capabilities
before applying user's request.
nodes capabilities. Add "Analog"/"Digital" marks to the pcm device names.
I hope it will help new users easier accept concept of several PCM devices
and understand exact purposes of that devices.
- invert sense of hw.cxgb.singleq tunable to hw.cxgb.multiq
- don't wake up transmitting thread by default
- add per tx queue ifaltq to handle ALTQ
- remove several unused functions in cxgb_multiq.c
- add several sysctls: multiq_tx_enable, coalesce_tx_enable,
and wakeup_tx_thread
- this obsoletes the hw.cxgb.snd_queue_len as ifq is replaced
by a buf_ring
and ifnet functions
- add memory barriers to <machine/atomic.h>
- update drivers to only conditionally define their own
- add lockless producer / consumer ring buffer
- remove ring buffer implementation from cxgb and update its callers
- add if_transmit(struct ifnet *ifp, struct mbuf *m) to ifnet to
allow drivers to efficiently manage multiple hardware queues
(i.e. not serialize all packets through one ifq)
- expose if_qflush to allow drivers to flush any driver managed queues
This work was supported by Bitgravity Inc. and Chelsio Inc.
1) Fix a bug in dealing with the Alerus 1006 PHY which prevented the
device from ever coming back up once it had been set to down.
2) Add a kernel tunable (hw.cxgb.snd_queue_len) which makes it possible
to give the device more than IFQ_MAXLEN entries in its send queue. The
default remains 50.
3) Add code to place the card'd identification and serial number into
its description (%desc) so that users can tell which card they have
installed.
and output, set BUS_DMA_COHERENT when creating the DMA map used for
loading the buffer. As a side-effect this solves locking issues on
sparc64 when dcons(4) calls bus_dmamap_sync(9) while in an interrupt
filter, which are executed in a critical section, and iommu(4) has
to use a sleep lock when taking advantage of the streaming buffer.
Reported and tested by: kensmith
Approved by: simokawa
For some reason the nmdm(4) driver doesn't use CALLOUT_MPSAFE, even
though we live in the MPSAFE TTY era. Add the CALLOUT_MPSAFE flags.
System survives.
for virtualization.
Instead of initializing the affected global variables at instatiation,
assign initial values to them in initializer functions. As a rule,
initialization at instatiation for such variables should never be
introduced again from now on. Furthermore, enclose all instantiations
of such global variables in #ifdef VIMAGE_GLOBALS blocks.
Essentialy, this change should have zero functional impact. In the next
phase of merging network stack virtualization infrastructure from
p4/vimage branch, the new initialization methology will allow us to
switch between using global variables and their counterparts residing in
virtualization containers with minimum code churn, and in the long run
allow us to intialize multiple instances of such container structures.
Discussed at: devsummit Strassburg
Reviewed by: bz, julian
Approved by: julian (mentor)
Obtained from: //depot/projects/vimage-commit2/...
X-MFC after: never
Sponsored by: NLnet Foundation, The FreeBSD Foundation
src/sys/dev/usb2/core/usbdevs
src/sys/dev/usb2/include/urio2_ioctl.h
src/sys/dev/usb2/storage/ustorage2_fs.h
These files are not used any more.
src/usr.sbin/Makefile
src/etc/mtree/BSD.include.dist
src/include/Makefile
src/lib/Makefile
src/share/man/man7/hier.7
src/share/mk/bsd.libnames.mk
src/etc/mtree/BSD.include.dist
Make "usbconfig" and "libusb20" a part of the default build.
src/sys/dev/usb/rio500_usb.h
src/sys/dev/usb2/storage/urio2.c
Use common include file.
src/sys/dev/usb2/bluetooth/ng_ubt2.c
Make USB bluetooth depend on "ng_hci" module.
src/sys/dev/usb2/controller/ehci2.c
src/sys/dev/usb2/controller/ehci2.h
Patches for Marvell EHCI.
src/sys/dev/usb2/core/usb2_busdma.c
Bugfix for 64-bit platforms. Need to unload the previously loaded DMA
map and some cleanup regarding some corner cases.
src/sys/dev/usb2/core/usb2_core.h
src/sys/dev/usb2/core/usb2_dev.c
src/sys/dev/usb2/core/usb2_dev.h
Bugfix for libusb filesystem interface.
New feature: Add support for filtering device data at the expense of the
userland process.
Add some more comments.
Some minor code styling.
Remove unused function, usb2_fifo_get_data_next().
Fix an issue about "fifo_index" being used instead of "ep_index".
src/sys/dev/usb2/core/usb2_device.c
src/sys/dev/usb2/core/usb2_generic.c
Bugfix for Linux USB compat layer. Do not free non-generic FIFOs when
doing an alternate setting.
Cleanup USB IOCTL and USB reference handling.
Fix a corner case where USB-FS was left initialised after
setting a new configuration or alternate setting.
src/sys/dev/usb2/core/usb2_hub.c
Improvement: Check all USB HUB ports by default at least one time.
src/sys/dev/usb2/core/usb2_request.c
Bugfix: Make sure destination ASCII string is properly zero terminated
in all cases.
Improvement: Skip invalid characters instead of replacing with a dot.
src/sys/dev/usb2/core/usb2_util.c
src/sys/dev/usb2/image/uscanner2.c
Spelling.
src/sys/dev/usb2/include/Makefile
Share "usbdevs" with the old USB stack.
src/sys/dev/usb2/include/usb2_devid.h
src/sys/dev/usb2/include/usb2_devtable.h
Regenerate files.
Alfred: Please fix the RCS tag at the top.
src/sys/dev/usb2/include/usb2_ioctl.h
Fix compilation of "kdump".
src/sys/dev/usb2/serial/ubsa2.c
src/sys/dev/usb2/serial/ugensa2.c
Remove device ID's which will end up in a new 3G driver.
src/sys/dev/usb2/sound/uaudio2.c
Correct a debug printout.
src/sys/dev/usb2/storage/umass2.c
Sync with old USB stack.
src/lib/libusb20/libusb20.3
Add more documentation.
src/lib/libusb20/libusb20.c
Various bugfixes and improvements.
src/usr.sbin/usbconfig/dump.c
src/usr.sbin/usbconfig/usbconfig.c
New commands for dumping strings and doing custom USB requests from
the command line.
Remove keyword requirements from generated files:
"head/sys/dev/usb2/include/usb2_devid.h"
"head/sys/dev/usb2/include/usb2_devtable.h"
- An "at" hint now reserves a device name.
- A new BUS_HINT_DEVICE_UNIT method is added to the bus interface. When
determining the unit number of a device, this method is invoked to
let the bus driver specify the unit of a device given a specific
devclass. This is the only way a device can be given a name reserved
via an "at" hint.
- Implement BUS_HINT_DEVICE_UNIT() for the acpi(4) and isa(4) bus drivers.
Both of these busses implement this by comparing the resources for a
given hint device with the resources enumerated by ACPI/PnPBIOS and
wire a unit if the hint resources are a subset of the "real" resources.
- Use bus_hinted_children() for adding hinted devices on isa(4) busses
now instead of doing it by hand.
- Remove the unit kludging from sio(4) as it is no longer necessary.
Prodding from: peter, imp
OK'd by: marcel
MFC after: 1 month
read before we configure the card, so we can implement
/dev/cardbus*.cis. Also, do this on a per-child basis, so we now have
a different name than before. I think i'll have to fix that for some
legacy tools to keep working.
I can now do a dumpcis on my running atheros card and have it still work!
redundant malloc/free. Add comments about how this should really be
done. Fix an overly verbose comment about under 1MB mapping: go ahead
and set the bits, but we ignore them.
- If the flag is set and auto-select fails, assume disk is not present.
- Set disk empty flag only when the floppy controller reset is needed.
It fixes regression introduced in r1.311, which prevented it from ignoring
errors. Now fdformat(1) and dd(1) with conv=noerror option can continue
when read/write errors occur as they should.
- Do not retry disk probing as it is extremely slow and pointless.
- Move the disk probing code into a separate function.
- Do not reset disk empty flag if write-protect check fails somehow.
PR: kern/116538[1]
the softc is reset a few times during probing.
Print 'changing to modem mode' messages if booting verbose to show the
reason for the time delay. Note: Some devices (Huawei for one) take 20
seconds to appear on the USB bus).
can be controlled by ifconfig(8). Note, VLAN hardware tagging
controls still lacks required handler but it requires more driver
cleanups so I didn't touch that part.
PR: kern/128766
- Fix to ioctl path in which the length could be 0 which means
no data in/out from LSI.
- Fix to ioctl path in which the data in the sense data space
of the ioctl packet is a really a pointer to some location in
user-space. From LSI re-worked a bit by me.
- Add HW support for next gen cards from LSI.
Thanks to LSI for their support!
Submitted by: jhb, LSI
MFC after: 3 days
The same (vendor, product) tuple is used for aue(4) adapters,
but I am not sure if the quirk is correct. I'm using the USB
device 'release' info to skip aue(4) detection right now, but
if there's a better way to differentiate between USB-LAN and
USB Bluetooth we should update the quirk.
Reviewed by: imp, rink
MFC after: 2 weeks
controller. The controller is also known as L1E(AR8121) and
L2E(AR8113/AR8114). Unlike its predecessor Attansic L1,
AR8121/AR8113/AR8114 uses completely different Rx logic such that
it requires separate driver. Datasheet for AR81xx is not available
to open source driver writers but it shares large part of Tx and
PHY logic of L1. I still don't understand some part of register
meaning and some MAC statistics counters but the driver seems to
have no critical issues for performance and stability.
The AR81xx requires copy operation to pass received frames to upper
stack such that ale(4) consumes a lot of CPU cycles than that of
other controller. A couple of silicon bugs also adds more CPU
cycles to address the known hardware bug. However, if you have fast
CPU you can still saturate the link.
Currently ale(4) supports the following hardware features.
- MSI.
- TCP Segmentation offload.
- Hardware VLAN tag insertion/stripping with checksum offload.
- Tx TCP/UDP checksum offload and Rx IP/TCP/UDP checksum offload.
- Tx/Rx interrupt moderation.
- Hardware statistics counters.
- Jumbo frame.
- WOL.
AR81xx PCIe ethernet controllers are mainly found on ASUS EeePC or
P5Q series of ASUS motherboards. Special thanks to Jeremy Chadwick
who sent the hardware to me. Without his donation writing a driver
for AR81xx would never have been possible. Big thanks to all people
who reported feedback or tested patches.
HW donated by: koitsu
Tested by: bsam, Joao Barros <joao.barros <> gmail DOT com >
Jan Henrik Sylvester <me <> janh DOT de >
Ivan Brawley < ivan <> brawley DOT id DOT au >,
CURRENT ML
- Do not let individual KLD module unregister firmware image loaded by ispfw
or vice versa.
- Make 'kldunload ispfw' actually unregister all firmware images loaded by
ispfw, not just 'isp_1040'.
- Print which KLD module actually loaded the firmware image.
- Remove unused return value from do_load_fw() and do_unload_fw() and remove
duplicate sys/param.h while I am here.
dependencies. A 'struct pmc_classdep' structure describes operations
on PMCs; 'struct pmc_mdep' contains one or more 'struct pmc_classdep'
structures depending on the CPU in question.
Inside PMC class dependent code, row indices are relative to the
PMCs supported by the PMC class; MI code in "hwpmc_mod.c" translates
global row indices before invoking class dependent operations.
- Augment the OP_GETCPUINFO request with the number of PMCs present
in a PMC class.
- Move code common to Intel CPUs to file "hwpmc_intel.c".
- Move TSC handling to file "hwpmc_tsc.c".
On RELENG_6 (and probably RELENG_7) we see our syscons windows and
pseudo-terminals have the following buffer sizes:
| LINE RAW CAN OUT IHIWT ILOWT OHWT LWT COL STATE SESS PGID DISC
| ttyv0 0 0 0 7680 6720 2052 256 7 OCcl 1146 1146 term
| ttyp0 0 0 0 7680 6720 1296 256 0 OCc 82033 82033 term
These buffer sizes make no sense, because we often have much more output
than input, but I guess having higher input buffer sizes improves
guarantees of the system.
On MPSAFE TTY I just sent both the input and output buffer sizes to 7
KB, which is pretty big on a standard FreeBSD install with 8 syscons
windows and some PTY's. Reduce the baud rate to 9600 baud, which means
we now have the following buffer sizes:
| LINE INQ CAN LIN LOW OUTQ USE LOW COL SESS PGID STATE
| ttyv0 1920 0 0 192 1984 0 199 7 2401 2401 Oil
| pts/0 1920 0 0 192 1984 0 199 5631 1305 2526 Oi
This is a lot smaller, but for pseudo-devices this should be good
enough. You need to do a lot of punching to fill up a 7.5 KB input
buffer. If it turns out things don't work out this way, we'll just
switch to 19200 baud.
NATM needs 'struct in_addr' to compile, which is a problem on its own
but include in.h for now if we have NATM but neither INET or INET6.
MFC after: 2 months
the sc does not have 'an_have_rssimap' variable.
Add an ANCACHE check to poperly hide the case and make an(4)
compile without INET.
MFC after: 2 months
Because the TTY hooks interface was not finished when I imported the
MPSAFE TTY layer, I had to disconnect the snp(4) driver. This snp(4)
implementation has been sitting in my P4 branch for some time now.
Unfortunately it still doesn't use the same error handling as snp(4)
(returning codes through FIONREAD), but it should already be usable.
I'm committing this to SVN, hoping someone else could polish off its
rough edges. It's always better than having a broken driver sitting in
the tree.
Note that these changes will not make the driver work on powerpc, but it should fix at least the i386/amd64 cases.
Obtained from: //depot/projects/usb/src/sys/dev/usb2/wlan/if_zyd2.c#20
Noticed by: jeli, ed
vnode in question does not need to be held. All the data structures used
during the name lookup are protected by the global name cache lock.
Instead, the caller merely needs to ensure a reference is held on the
vnode (such as vhold()) to keep it from being freed.
In the case of procfs' <pid>/file entry, grab the process lock while we
gain a new reference (via vhold()) on p_textvp to fully close races with
execve(2).
For the kern.proc.vmmap sysctl handler, use a shared vnode lock around
the call to VOP_GETATTR() rather than an exclusive lock.
MFC after: 1 month
that includes significant features and SMP safety.
This commit includes a more or less complete rewrite of the *BSD USB
stack, including Host Controller and Device Controller drivers and
updating all existing USB drivers to use the new USB API:
1) A brief feature list:
- A new and mutex enabled USB API.
- Many USB drivers are now running Giant free.
- Linux USB kernel compatibility layer.
- New UGEN backend and libusb library, finally solves the "driver
unloading" problem. The new BSD licensed libusb20 library is fully
compatible with libusb-0.1.12 from sourceforge.
- New "usbconfig" utility, for easy configuration of USB.
- Full support for Split transactions, which means you can use your
full speed USB audio device on a high speed USB HUB.
- Full support for HS ISOC transactions, which makes writing drivers
for various HS webcams possible, for example.
- Full support for USB on embedded platforms, mostly cache flushing
and buffer invalidating stuff.
- Safer parsing of USB descriptors.
- Autodetect of annoying USB install disks.
- Support for USB device side mode, also called USB gadget mode,
using the same API like the USB host side. In other words the new
USB stack is symmetric with regard to host and device side.
- Support for USB transfers like I/O vectors, means more throughput
and less interrupts.
- ... see the FreeBSD quarterly status reports under "USB project"
2) To enable the driver in the default kernel build:
2.a) Remove all existing USB device options from your kernel config
file.
2.b) Add the following USB device options to your kernel configuration
file:
# USB core support
device usb2_core
# USB controller support
device usb2_controller
device usb2_controller_ehci
device usb2_controller_ohci
device usb2_controller_uhci
# USB mass storage support
device usb2_storage
device usb2_storage_mass
# USB ethernet support, requires miibus
device usb2_ethernet
device usb2_ethernet_aue
device usb2_ethernet_axe
device usb2_ethernet_cdce
device usb2_ethernet_cue
device usb2_ethernet_kue
device usb2_ethernet_rue
device usb2_ethernet_dav
# USB wireless LAN support
device usb2_wlan
device usb2_wlan_rum
device usb2_wlan_ral
device usb2_wlan_zyd
# USB serial device support
device usb2_serial
device usb2_serial_ark
device usb2_serial_bsa
device usb2_serial_bser
device usb2_serial_chcom
device usb2_serial_cycom
device usb2_serial_foma
device usb2_serial_ftdi
device usb2_serial_gensa
device usb2_serial_ipaq
device usb2_serial_lpt
device usb2_serial_mct
device usb2_serial_modem
device usb2_serial_moscom
device usb2_serial_plcom
device usb2_serial_visor
device usb2_serial_vscom
# USB bluetooth support
device usb2_bluetooth
device usb2_bluetooth_ng
# USB input device support
device usb2_input
device usb2_input_hid
device usb2_input_kbd
device usb2_input_ms
# USB sound and MIDI device support
device usb2_sound
2) To enable the driver at runtime:
2.a) Unload all existing USB modules. If USB is compiled into the
kernel then you might have to build a new kernel.
2.b) Load the "usb2_xxx.ko" modules under /boot/kernel having the same
base name like the kernel device option.
Submitted by: Hans Petter Selasky hselasky at c2i dot net
Reviewed by: imp, alfred
Also: Change the initialisation of the command string to a static
initialiser. Verify it against the output of umass.c when being sent a
command using 'camcontrol eject da0' to a Bulk-Only device.
This should make those devices work that need a SCSI eject command to
switch to modem mode (Novatel 950D and others).
allocating resources to read the CIS. I'm not sure when this changed,
but it is totally wrong. Also, add a minor improvement to the
debugging.
This should help everybody trying to run dumpcis on atheros wireless
card as well.
MFC after: 2 days
right... Good thing the size was ignored...
Where this macro is used, there's no reason to do it anyway. There
seems to have been some old-time confusion between the CIS pointer
definition, and the BAR definitions at the base of this bug.
compiled into the main AMR driver. It's code that is nice to have but not
required for normal operation, and it is reported to cause problems for some
people.
For an unknown reason the touch pad of my PowerBook generates button 5
events when you operate it. This causes the adb_mouse code to convert
them to button 2 events, which is not what we want.
Add a new flag, AMS_TOUCHPAD, which is used to distinguish the touch
pad. When set, don't convert button events of unknown buttons to the
last button.
There are still three problems left with respect to user input:
- The mouse button events are not properly processed when the touch pad
isn't touched.
- The arrow keys on the keyboard don't work inside X11.
- The power button isn't handled by the kernel, similar to the ACPI
power button on i386/amd64.
Approved by: nwhitehorn
use process ID as ACPI thread ID. Concurrent requests with equal thread
IDs broke ACPI mutexes operation causing unpredictable errors including
AE_AML_MUTEX_NOT_ACQUIRED that I have seen.
Use kernel thread ID instead of process ID for ACPI thread.
Right now ams_read() uses cv_wait() to wait for new data to arrive on
the mouse device. This means that when you run `cat /dev/ams0', it
cannot be interrupted directly. After you press ^C, you first need to
move the mouse before cat will quit. Make this function use
cv_wait_sig(), which allows it to be interrupted directly.
Reviewed by: nwhitehorn
