- The 6000 series WiMAX devices need a separate firmware.
- The b-gen devices are not hooked because the hardware revision type
is not know.
Obtained from: OpenBSD
MFC after: 1 week
r165114 added that code and that change ignored the same logic
committed in r135772. In addition, data FIFO protection should be
selectively enabled instead of applying to all PCIe devices.
While I'm here add BCM5785 to devices that do not require this
fix.
and remove a buffer overflow:
- Remove the array of per-type dispatch functions. Instead, pass each
structure to a single callback. The callback should check the type of
each table entry to take appropriate action. This matches the behavior
of other table walkers such as for the MP Table and MADT.
- Don't attempt to save an array of string pointers for each structure
entry. Instead, just skip the strings. If this code is reused to
provide a generic SMBIOS table walker in the future we could provide
a method that looks up a specific string N for a given structure record
instead of pre-populating an array of pointers. This fixes a buffer
overflow for structure entries with more than 20 strings.
PR: kern/148546
Reported by: Spencer Minear @ McAfee
MFC after: 3 days
The code in question verifies that all register write operations only change
bits that are defined (in the register definition file) for that effected
register. The bug effectively disabled this checking.
o Fix the check by testing the opcode against all supported read ("and" based)
operands.
o Add missing bit definitions to the aic7xxx and aic79xx register definition
files so that the warning (treated as a fatal error) does not spuriously
fire.
Reported by: Pawel Worach <pawel.worach@gmail.com>
MFC after: 1 week
All of the necessary wrmsr calls are now preceded by a rdmsr
and we leave the reserved bits alone.
Document the bits in the relevant registers for future reference.
Tested by: mdf
MFC after: 1 week
was missed in r209599.
Reported and tested by: Michael Moll
- Declare mpt_dma_buf_alloc() static just like mpt_dma_buf_free(), both are
used in mpt.c only.
Reviewed by: ken
MFC after: r209599
a packet has only a header in the first mbuf, the
checksum code will dereference a pointer into the
non-existing IP header. Do a check for the size and
pullup if needed. Thanks to Michael Tuexen for this
fix.
MFC: asap - should be in 8.1 IMHO
Do not grab lock while setting up interrupt, as it causes LOR with
allocation code. Instead make interrupt handler check that CAM bus
initialization completed before touching it.
While there, slightly improve attach errors handling.
Reported by: kib
The following systems are affected:
- MPC8555CDS
- MPC8572DS
This overhaul covers the following major changes:
- All integrated peripherals drivers for Freescale MPC85XX SoC, which are
currently in the FreeBSD source tree are reworked and adjusted so they
derive config data out of the device tree blob (instead of hard coded /
tabelarized values).
- This includes: LBC, PCI / PCI-Express, I2C, DS1553, OpenPIC, TSEC, SEC,
QUICC, UART, CFI.
- Thanks to the common FDT infrastrucutre (fdtbus, simplebus) we retire
ocpbus(4) driver, which was based on hard-coded config data.
Note that world for these platforms has to be built WITH_FDT.
Reviewed by: imp
Sponsored by: The FreeBSD Foundation
start so we should adjust the mbuf if the driver is running in PIO mode.
Now it should work well with WPA authentication and association for LP
PHY devices.
Tested by: Warren Block <wblock at wonkity.com>
MFC after: 1 month
checksum offloading is enabled. The frame has a valid checksum
value so payload might be modified during TX checksum calculation.
Disable TX checksum offloading but give users chance to enable it
when they know their controller works without problems with TX
checksum offloading.
Reported by: Andrzej Tobola <ato <> iem dot pw dot edu dot pl>
- Run the adapter's tick at 1Hz and remove link state checks from it.
Instead, have each port check its link state. Delay the check so that
it takes place slightly after the driver is notified of a change in
link state. This is a cheap way to debounce these notifications if
many are received in rapid succession. POLL_LINK_1ST_TIME flag can
also be eliminated as a side effect of these changes.
- Do not reset the PHY when link goes down.
- Clear port's link_fault flag if the PHY indicates link is down.
- get_link_status_r should leave speed and duplex alone when link is down.
MFC after: 1 month
checksum is enabled in sge_init_locked().
While I'm here do not set RX checksum bits in RX descriptor
initialization. It is controller's job to set these bits.
Tested by: xclin <xclin <> cs dot nctu dot edu dot tw >