resource. Avoids useless interrupts occurring between the allocation
of the interrupt resource and the final initialisation of the
kernel. Cause of these interrupts is unknown (a resuming device?).
Add an emply MAIN__() function. This avoid an unresolved reference error
during link phase when using fortran subroutines with non-fortran 'main()'.
Obtained from: src/lib/libF77/MAIN.c rev 1.1 by jmz
* Don't buffer "Digesting..." output - flush it immediately.
* Increase the number of repetitions by a factor of 100, and the block size by
a factor of 10 so as to give meaningful results on modern machines (108
seconds on my P120, and ~26 seconds on a P-II 350).
PR: bin/10604
Submitted by: Stanislav Shalunov <shalunov@lynxhub.lz.att.com>
range attributes after they have been extracted from the master.
Hook up the i686 MP code to do this for each AP.
Be more careful about printing the default memory type for the i686.
Suggestions from: luoqi
in libstdc++.
Until I have a chance to look at what that problem is and to carefully consider
the upgrade issues of turning it back on at a later date if we leave it turned
off for any extended peroid of time.
"passwordtime" is what passwd(1) has actually been using. I suspect
passwordperiod was the original intent. I can't figure-out which,
if either, BSDi uses. If anyone knows...
This really fixes the condition where a child creates children of its own.
I'm leaving the previous sanity tests in though, since they shouldn't hurt,
and will give an indication if this ever happens again.
- Try to unbreak what I broke by screwing with the tx queuing again.
I'm waiting for a few more people to test out this code and report back
before I move it into current. Hopefully it will be soon. Basically I
reverted to the old TX queuing strategy.
- Add experimental support for the 3c900B-FL (10mbps ST fiber). The card
should be detected properly and the 10baseFL mode supported, but again
I'm still waiting for word from a tester to see if this actually works.
It shouldn't affect the other cards though; all the differences are in
media selection.
- Set the TX start threshold register to get better performance.
- Increase the size of the RX and TX rings. UDP performance was pretty
bad because the TX ring was too small. Should be substantially better
now (I can saturate the link with either TCP or UDP now).
- Change some of the #defines to reflect proper 3Com ASIC names (boomerang,
cyclone, krakatoa, hurricane).
- Simplify and reorganize interrupt handler; ack all interrupts right
away and then process them. This avoids a potential race condition.
(Noted by Matt Dillon.)
- Reorganize the bridging code to eliminate using a goto to jump into
the middle of an if() {} clause. Sorry, that just made my brain itch.
- Use m_adj() in xl_rxeof().
- Make the payload alignment in xl_newbuf() the default (instead of
just conditionally defined for the alpha) to improve NFS performance
(avoids need for nfs_realign()).
That doesn't work well for tapes over 4G.
I use tcopy a lot to write images of a tape to tape as tape to tape
copying is terribly slow. Slower than it should be. Quickly found out
tcopy can not rewind a file when doing copy/verify.
PR: 11386
Submitted by: David Kelly dkelly@hiwaay.net
Reviewed by: phk
This patch also moves the bogus comment (the comment is still not quite
right) and (as a side effect) removes some verbose initialisations (we
depend on static initialisation to 0 for almost everything in proc0).
The alpha kernels are bootable again. The change won't affect i386's
until machdep.c is changed.
Submitted by: bde
try to fork() a child of its own, which could result in several children
ypservs running at once. I'm still not sure exactly what leads to this
condition, but these fixes should stop it from causing trouble. A new
function, yp_fork() checks to see if the current process is already a
child of the parent ypserv, and returns failure (and logs an error message)
rather than spawning another child.
