In my specific case, this fixes the problem of my PowerMac G5 displaying a
4:3 console on a 16:10 display with black bars on the left and right.
PR: kern/180558
Reviewed by: nwhitehorn
MFC after: 5 days
1) Add support for page back/forward.
2) While doing HOR scrolling, disable VER scrolling.
3) Checking dx_sum and dy_sum before emulate right button, this can
avoids unexpected right button press.
4) Fix stable pointer operation when emulating middle button.
Submitted by: Huang Wen Hui <huanghwh@gmail.com>
MFC after: 2 weeks
It's still hardcoded (for db120) but it is now hardcoded in all the
same place (ie, the pdata path.) The port config/status code now checks
port0/port6 as appropriate to configure things.
Tested:
* Qualcomm Atheros DB120, AR8327 switch.
This is (almost!) enough to actually probe, attach, configure a default
port group and do some basic work. It's also totally hard-coded for
the Qualcomm Atheros DB120 board - it doesn't yet have any of the code
from OpenWRT which parses extra configuration data to know how to program
the switch. The LED stuff is also missing.
But, it's enough to facilitate board, PHY, switch and VLAN bringup,
so I am committing it now.
Tested:
* Qualcomm Atheros DB120
Obtained from: OpenWRT
switches.
* Add some new VLAN HAL methods that will be used by the VLAN configuration
code. The AR933x and later switches use slightly different register
layouts (even though the driver currently doesn't support it.)
- Support for double-tap and drag.
- Support for 2-finger horizontal scrolling which translates to page-back/forward events.
- Single finger tap is equivalent to a left-button press.
- Two-finger taps are mapped to the right-button click.
- Three fingers are mapped to middle button.
- Add sysctl to disable single finger tapping.
- Fix for multiple open of /dev/atp0
- Enhanced support for the Fountain/Geyser family by adding Geyser4.
- Update manual page.
Submitted by: Rohit Grover <rgrover1@gmail.com>
MFC after: 2 weeks
HAL methods.
This allows the AR8327 code to override it as appropriate.
Tested:
* DB120 - AR8327 and AR9340 on-board switch; only running 'etherswitchcfg'
to check configs. The actual VLAN programming wasn't tested.
The registers (and perhaps the flags) are different for the AR8327, so
I'll stub those out until they're written.
Tested:
* DB120 - both on-chip AR9340 and AR8327 switches.
a single port to setup.
This may end up later being used as part of some logic to program
the PHY for a single port, rather than having to reinitialise them
all at once.
Tested:
* DB120
- intercept FIONBIO and FIOASYNC ioctls on netmap file descriptors.
libpcap calls them to set non blocking I/O on the file descriptor,
for netmap this is a no-op because there is no read/write,
but not intercepting would cause fcntl() to return -1
- rate limit and put under netmap.verbose some messages that occur
when threads use concurrently the same file descriptor.
Before this patch, curvnet was NULL.
When the VIMAGE kernel option is enabled, this eliminates
kernel panics when USB ethernet devices are plugged in.
PR: 183835
Submitted by: Hiroo Oono <hiroo.ono at gmail dot com>
about uss820dci_odevd being unused, by adding it to the part that
handles getting descriptors.
Reported by: loos
Reviewed by: hselasky
MFC after: 3 days
rather than SDHCI_RESET_ALL; the latter turns off clocks and power, removing
any possibility of recovering from the error.
Also, double the timeout to 2 seconds. Despite what the SD spec says about
all transactions completing in 250ms or less, I have a card which sometimes
takes more than a second to complete a write.
