Discussed in from [FreeBSD-tech-jp 3396] to [FreeBSD-tech-jp 3407]
at FreeBSD-tech-jp@jp.freebsd.org.
NOTE: We must put ed_probe_SIC() function into if_ed_isa.c because
this is a bus dependent code. But the ed driver code is not
separated explicitly whether it is bus dependent or independent
now.
Refer to: http://plaza17.mbn.or.jp/~chi/myprog/FreeBSD/sicat.html
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
not from the probe routine. This was an oversight when I originally
ported the miibus support to -current, though it was mostly harmless.
We now set the vendor code to the new value ED_VENDOR_LINKSYS in
ed_pccard_Linksys() at probe time. Then ed_pccard_attach() checks
the vendor code, and sets up the miibus if appropriate.
Reviewed by: imp
bolted to a ne-2000 chip. This is necessary for the NetGear FA-410TX
and other cards.
This also requires you add mii to your kernel if you have an ed driver
configured.
This code will result in a couple of timeout messages for ed on the
impacted cards. Additional work will be needed, but this does work
right now, and many people need these cards.
Submitted by: Ian Dowse <iedowse@maths.tcd.ie>
require the addition of flag 0x80000 to their config line in
pccard.conf(5). This flag is not optional. These Linksys cards will
not be recognized without it.
Reviewed by: imp, iwasaki
`ED_P1_MAR + i' and `ED_P1_PAR + i', respectively.
- convert ED_PC_RESET and ED_PC_MISC into relative offset from
ED_PC_ASIC_OFFSET (those macros are not used in current source).
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
scheduled for demolition. This is a first step: get rid of if_zereg.h,
by adding the five extra definitions to if_edreg.h.
Also add some definitions which will become needed when if_ze.c gets
replaced entirely by pccard and if_ed.c. (this is a 2.1.0 candidate)
finally have the f**king documentation!):
1) Changed all the numeric register offsets to symbolic ones (it should
have been this way originally).
2) If 16 bit, disable the shared memory when not using it. Apparantly
switching between 8/16bit mode makes the Ultra unhappy unless
this is done (i.e. it trashes the bus).
* merged in Garrett Wollman's strict prototype changes
*
* Revision 2.15 1993/11/29 16:32:58 davidg
* From Thomas Sandford <t.d.g.sandford@comp.brad.ac.uk>
* Add support for the 8013W board type
* change all splnet's to splimp's
*
* Revision 2.13 1993/11/22 10:53:52 davidg
* patch to add support for SMC8216 (Elite-Ultra) boards
* from Glen H. Lowe
*
* Revision 2.12 1993/11/07 18:04:13 davidg
* fix from Garrett Wollman:
* add a return(0) at the end of ed_probe so that if the various device
* specific probes fail that we just don't fall of the end of the function.
* added no multi-buffer override for 3c503
*
* Revision 2.1 93/09/29 12:32:12 davidg
* changed multi-buffer count for 16bit 3c503's from 5 to 2 after
* noticing that the transmitter becomes idle because of so many
* packets to load.
*
* Revision 2.0 93/09/29 00:00:19 davidg
* many changes, rewrites, additions, etc. Now supports the
* NE1000, NE2000, WD8003, WD8013, 3C503, 16bit 3C503, and
* a variety of similar clones. 16bit 3c503 now does multi
* transmit buffers. Nearly every part of the driver has
* changed in some way since rev 1.30.
1) fixed 3c503 lock-up if the thinwire cable was disconnected at boot time
2) 8013EBT boards now work (quite well!) in 16bit/16k mode
3) ED_NO_DOUBLE_BUFFERING flag now works
4) slightly higer performance (about 3%) with 16bit WD/SMC boards
5) support for WD8013WC (10BaseT) boards
Additionally, the probe code has been reorganized to be much cleaner. This
revision of the driver is 1.25. The release notes have been updated as well.
8bit or 16bit operation, and a flag to disable transmitter double buffering.
See the updated "ed.relnotes" file for information about how to set
the flags.
This should be considered the first "production" release. It still
needs a manual page, though.
